| Commit message (Collapse) | Author | Age | Lines |
|\
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
common/cmd_bootm.c
cpu/mpc8xx/cpu.c
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
|
| |\ |
|
| |\ \ |
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
New uImage format (Flattened Image Tree) requires libfdt
functionality, print out error message if CONFIG_OF_LIBFDT
is not defined.
New uImage support is enabled by defining CONFIG_FIT (and CONFIG_OF_LIBFDT).
This commit turns it on by default.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
device_type = "soc" is being deprecated, newer device trees will use
"fsl,soc" and/or "fsl,immr" for the soc nodes.
This patch also adds clock-frequency property for soc nodes (the same
value as bus-frequency).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch adds few routines to configure serdes on 837x targets.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
..plus get rid of some #ifdefs in the .c files.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The following changes are based on kernel UCC ethernet performance:
1. Make the CSB bus pipeline depth as 4, and enable the repeat mode
2. Optimize transactions between QE and CSB. Added CFG_SPCR_OPT
switch to enable this setting.
The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:
3. CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4. CS0_CONFIG[ODT_WR_CONFIG] set to 1. Was a reserved setting
previously.
5. TIMING_CFG_1[WRREC] is changed from 3clks to 2clks (based on
Twr=15ns, and this was already the setting in DDR_MODE)
6. TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
Trp=15ns)
7. TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
Tras=40ns)
8. TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
Trcd=15ns)
9. TIMING_CFG_1[REFREC] changed from 21 clks to 11clks. (based on
Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks. (based
on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
on CL=3 and WL=2).
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
|
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|\ \ \ \ |
|
| | | | |
| | | | |
| | | | |
| | | | | |
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
You can't judge UNCACHED by Config.K0 LSB.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Handles machine specific functions by using weak functions.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Add setup_c0_status from Linux. For the moment we disable interrupts, set
CU0, mark the kernel mode, and clear ERL and EXL. This is good enough for
reset-time configuration and will work well across most processors.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Without this change, we'll be suffering from deffered WATCH exception
once Status.EXL is cleared. Make sure Cause.WP is cleared.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Move things to appropriate place.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
We do Hit_Writeback_Inv_D and Hit_Invalidate_I. You might think that you
don't need to do Hit_Invalidate_I, but flush_cache() needs it since this
function is used not only in U-Boot specfic programs but also at loading
target binaries.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Currently we do 1) Index_Store_Tag_I, 2) Fill and 3) Index_Store_Tag_I
again per a loop for I-cache initialization. But according to 'See MIPS
Run', we're encouraged to use three separate loops rather than combining
them *for both I- and D-cache*. This patch tries to fix this.
In accordance with fixing above, mips_init_[id]cache are separated from
mips_cache_reset(), and rewrite cache loops are completely rewritten with
useful macros.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This routine fills memory with zero by 64 bytes, and is 64-bit capable.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This patch replaces the current function definitions with NESTED, LEAF
and END macro. They specify some more additional information about the
function; an alignment of symbol, type of symbol, stack frame usage, etc.
These information explicitly tells the assembler and the debugger about
the types of code we want to generate.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The initial intension of having mips_cache_lock() was to use the cache
as memory for temporary stack use so that a C environment can be set up
as early as possible.
But now mips_cache_lock() follow lowlevel_init(). We've already have the
real memory initilaized at this point, therefore we could/should use it.
No reason to lock at all.
Other problems:
Cache locking is not consistent across MIPS implementaions. Some imple-
mentations don't support locking at all. The style of locking varies -
some support per line locking, others per way, etc. Some parts use bits
in status registers instead of cache ops. Current mips_cache_lock() is
not necessarily general-purpose.
And this is worthy of special mention; once U-Boot/MIPS locks the lines,
they are never get unlocked, so the code relies on whatever gets loaded
after U-Boot to re-initialize the cache and clear the locks. We're sup-
posed to have CFG_INIT_RAM_LOCK and unlock_ram_in_cache() implemented,
but leave the situation as it is for a long time.
For these reasons, I proposed the removal of mips_cache_lock() from the
global start-up code.
This patch adds CFG_INIT_RAM_LOCK_MIPS to make existing users aware that
*things have changed*. If he wants the same behavior as before, he needs
to have CFG_INIT_RAM_LOCK_MIPS in his config file.
If we don't have any regression report through several releases, then
we'll remove codes entirely.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Acked-by: Andrew Dyer <amdyer@gmail.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Include FEC specific nodes in ft_cpu_setup only if CONFIG_MPC5xxx_FEC is
defined. Systems without FEC, i.e. no FEC node in DTB, should be possible.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
|
|/ / / /
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch does some shifting around of OF support on 8xx.
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Modify the RTC API to provide one a status for the time reported by
the rtc_get() function:
0 - a reliable time is guaranteed,
< 0 - a reliable time isn't guaranteed (power fault, clock issues,
and so on).
The RTC chip drivers are responsible for providing this info if the
corresponding chip supports such functionality. If not - always
report that the time is reliable.
The POST RTC test was modified to detect the RTC faults utilizing
this new rtc_get() feature.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
460EX doesn't support a fixed bootstrap option to boot from 512 byte page
NAND devices. The only bootstrap option for NAND booting is option F for
2k page devices. So to boot from a 512 bype page device, the I2C bootstrap
EEPROM needs to be programmed accordingly.
This patch adds basic NAND booting support for the AMCC Canyonlands aval
board and also adds support to the "bootstrap" command, to enable NAND
booting I2C setting.
Tested with 512 byte page NAND device (32MByte) on Canyonlands.
Signed-off-by: Stefan Roese <sr@denx.de>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch adds basic support for the AMCC 460EX/460GT PPC's.
Signed-off-by: Stefan Roese <sr@denx.de>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch adds basic support for the AMCC 460EX/460GT PPC's.
Signed-off-by: Stefan Roese <sr@denx.de>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch is a rework of the 4xx interrupt handling done while
adding the 460EX/GT support. Interrupts are needed on 4xx for the
EMAC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch changes the physical addess parameter from 32bit to 64bit.
This is needed for 36bit 4xx platforms to access areas located
beyond the 4GB border, like SoC peripherals (EBC etc.).
Signed-off-by: Stefan Roese <sr@denx.de>
|
| |_|/
|/| |
| | |
| | |
| | |
| | |
| | | |
While adding the 460EX/GT support I reworked the 4xx miiphy code. It
badly neede some cleanup.
Signed-off-by: Stefan Roese <sr@denx.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Every now and then a Sequoia board (or equivalent hardware) had
problems connecting to a Gigabit capable network interface.
There were differences in the PHY setup between Linux and U-Boot.
This patch fixes the problem. Apparently "remote fault" is being set,
which signals to some devices (on the other end of the cable) that a
fault has occurred, while other devices ignore it. I believe the RF bit
was causing the issue, but I removed T4 also, to match up with Linux.
Signed-off-by: Mike Nuss <mike@terascala.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The 405EZ only supports 512 bytes of rx-/tx-fifo EMAC sizes. But
currently 4k/2k is configured. This patch fixes this issue.
Thanks to Thomas Kindler <tkindler@lenord.de> for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|\ \ \ |
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
There is no reason to icbi when invalidating the temporary stack in
the d-cache. Its impossible on e500 to have the i-cache contain
any addresses in the temp stack and it can be problematic in generating
transactions on the bus to non-valid addresses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The source vector for the ECM was being set to 2,
but that's what the source vector for DDR was being
set to. Change it to 1.
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
| | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Commit 0db37dc... (and some others) changed the INIT_RAM TLB
mappings to be unguarded. This collided with an existing "bug"
where the mappings for the INIT_RAM were being kept around.
This meant that speculative loads to those addresses were
succeeding in the TLB, and going out to the bus, where they
were causing an exception (there's nothing at that address). The
Flash code was coincidentally causing such a speculative load.
Rather than go back to mapping the INIT RAM as guarded, we fix
it so that the entries for the INIT_RAM are invalidated. Thus
the speculative loads will fail in the TLB, and have no effect.
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Adds PCI support for MPC5121
Tested with drivers/net/rtl8139.c
Support is conditional since PCI on old silicon does not work.
ads5121_PCI_config turns on PCI
In this version, condition compilation of PCI code has been moved
from ifdef in board/ads5121/pci.c to board/ads5121/Makefile as
suggested by Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: John Rigby <jrigby@freescale.com>
|
|/ /
| |
| |
| |
| |
| |
| |
| |
| |
| | |
U-Boot crashes in the net loop if CONFIG_4xx_DCACHE is
enabled. To reproduce the problem ensure that 'ethrotate'
environment variable isn't set to "no" and then run
"tftp 200000 not_existent_file".
This patch tries to fix the issue.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
| |
| |
| |
| | |
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
| |
| |
| |
| |
| |
| | |
This will reduce the build time.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
| |
| |
| |
| |
| |
| | |
This will reduce the build time.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This reduces the build time by ~10%. Here's the gth2_config example.
BEFORE AFTER
real 0m31.441s 0m27.833s
user 0m24.766s 0m23.045s
sys 0m10.425s 0m7.468s
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
|\ \ |
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This is the proper fix for a missing closing brace in the function
ft_cpu_setup() noticed by joe.hamman <at> embeddedspecialties.com.
The ft_cpu_setup() function in mpc8641hpcn.c should have been
removed earlier as it was under the obsolete CONFIG_OF_FLAT_TREE,
but was missed. Only, the sbc8641d was nominally still using it.
It all got ripped out, and the funcality that was in ft_board_setup()
was refactored to remove the CPU portions into the new file
cpu/mpc86xx/fdt.c instead. Make sbc8641d use this now.
Based loosely on an original patch from joe.hamman@embeddedspecialties.com
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
| | |
| | |
| | |
| | |
| | |
| | | |
and remove useless CONFIG_DDR_INTERLEAVE
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
| |/
| |
| |
| | |
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|/
|
|
| |
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
|
|
| |
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
|
|
|
|
| |
fix mmc_bread function prototype
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|\ |
|