summaryrefslogtreecommitdiff
path: root/cpu/ppc4xx
Commit message (Collapse)AuthorAgeLines
* ppc4xx: Add weak default ft_board_setup() routineStefan Roese2008-05-08-3/+23
| | | | | | | | This patch adds a default ft_board_setup() routine to the 4xx fdt code. This routine is defined as weak and can be overwritten by a board specific one if needed. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Fix typos in 460GT/EX FBDV arrayDave Mitchell2008-05-08-1/+1
| | | | | | | Corrected two typos in the 460GT/EX FBDV array. Signed-off-by: Dave Mitchell <dmitchell@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Fix problem with DIMMs with 8 banks in 44x_spd_ddr2.cStefan Roese2008-04-30-2/+5
| | | | | | | | | This patch fixes a problem with DIMMs that have 8 banks. Now the MCIF0_MBxCF register will be setup correctly for this setup too. This was noticed with the 512MB DIMM on Canyonlands/Glacier. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Fix compilation warning in denali_spd_ddr2.cStefan Roese2008-04-29-0/+1
| | | | Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Complete remove bogus dflush()Stefan Roese2008-04-29-33/+5
| | | | | | | | | | Since the current dflush() implementation is know to have some problems (as seem on lwmon5 ECC init) this patch removes it completely and replaces it by using clean_dcache_range(). Tested on Katmai with ECC DIMM. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Fixup ebc clock in FDT for 405GP/EPMarkus Brunner2008-04-29-2/+8
| | | | | | | | On ppc405EP and ppc405GP (at least) the ebc is directly attached to the plb and not to the opb. This patch will try to fixup /plb/ebc if /plb/opb/ebc doesn't exist. Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xxWolfgang Denk2008-04-26-0/+42
|\
| * ppc4xx: Pass PCIe root-complex/endpoint configuration to Linux via the fdtStefan Roese2008-04-25-0/+42
| | | | | | | | | | | | | | | | | | | | The PCIe root-complex/endpoint setup as configured via the "pcie_mode" environment variable will now get passed to the Linux kernel by setting the device_type property of the PCIe device tree node. For normal root- complex configuration it will keep its defaults value of "pci" and for endpoint configuration it will get changed to "pci-endpoint". Signed-off-by: Stefan Roese <sr@denx.de>
* | USB: fix more GCC 4.2.x aliasing warningsWolfgang Denk2008-04-25-2/+2
|/ | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Markus Klotzbuecher <mk@denx.de>
* ppc4xx: Add dcache_enable() for 440Stefan Roese2008-04-22-0/+2
| | | | | | | | | | | | dcache_enable() was missing for 440 and the patch 017e9b7925f74878d0e9475388cca9bda5ef9482 ["allow ports to override bootelf "] behavior uses this function. Note: Currently the cache handling functions like d/icache_disable/enable() are NOP's on 440. This may be changed in the future. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Fix sys_get_info() for 405GP(r)Matthias Fuchs2008-04-21-0/+2
| | | | | | | | This patch assigns the correct EBC clock for 405GP(r) CPUs to PPC4xx_SYS_INFO structure. Without this patch U-Boot uses an uninitialized EBC clock in its startup message. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
* Fix crash on sequoia in ppc_4xx_eth_initAnatolij Gustschin2008-04-18-0/+4
| | | | | | | | Currently U-Boot crashes in ppc_4xx_eth_init on sequoia with cache enabled (TLB Parity exeption). This patch fixes the problem. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* ppc4xx: Fix crash on sequoia with cache enabledAnatolij Gustschin2008-04-18-1/+3
| | | | | | | | | | | Currently U-Boot crashes on sequoia board in CPU POST if cache is enabled (CONFIG_4xx_DCACHE defined). The cache won't be disabled by change_tlb before CPU POST because there is an insufficient adress range check since CFG_MEM_TOP_HIDE was introduced. This patch tries to fix this problem. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* ppc4xx: Fix 4xx enet driver to support 460GT EMAC2+3Stefan Roese2008-04-03-3/+13
| | | | | | | | This patch fixes a problem with the RGMII setup of the 460GT. The 460GT has 2 RGMII instances and we need to configure the 2nd RGMII instance for the EMAC2+3 channels. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Add CFG_MEM_TOP_HIDE to Denali SPD-based SDRAM setupLarry Johnson2008-03-31-13/+14
| | | | Signed-off-by: Larry Johnson <lrj@acm.org>
* ppc4xx: PPC405EP Set EMAC noise filter bitsMarkus Brunner2008-03-27-1/+1
| | | | | | | | | This bug was introduced with commit aee747f19b460a0e9da20ff21e90fdaac1cec359 which enabled CFG_4xx_GPIO_TABLE for PPC405 and unintentionally disabled the setting of the emac noise filter bits for PPC405EP when CFG_4xx_GPIO_TABLE is set. Signed-off-by: Markus Brunner <super.firetwister@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Reconfigure PLL for 667MHz processor for PPC440EPxMike Nuss2008-03-27-1/+99
| | | | | | | | | | | | On PPC440EPx without a bootstrap I2C EEPROM, the PLL can be reconfigured after startup to change the speed of the clocks. This patch adds the option CFG_PLL_RECONFIG. If this option is set to 667, the CPU initialization code will reconfigure the PLL to run the system with a CPU frequency of 667MHz and PLB frequency of 166MHz, without the need for an external EEPROM. Signed-off-by: Mike Nuss <mike@terascala.com> Acked-by: Stefan Roese <sr@denx.de>
* ppc4xx: Fix compilation warning in 4xx_enet.cStefan Roese2008-03-27-7/+6
| | | | Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Add AMCC Glacier 406GT eval board supportStefan Roese2008-03-27-3/+48
| | | | | | | | | | | | | | This patch adds support for the AMCC Glacier 460GT eval board. The main difference to the Canyonlands board are listed here: - 4 ethernet ports instead of 2 - no SATA port - no USB port Currently EMAC2+3 are not working. This will be fixed in a later release. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Mask 'vec' with 0x1f in uic_interrupt() for bit set/clearStefan Roese2008-03-27-3/+4
| | | | Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Add Canyonlands NAND booting supportStefan Roese2008-03-15-1/+7
| | | | | | | | | | | | | | | 460EX doesn't support a fixed bootstrap option to boot from 512 byte page NAND devices. The only bootstrap option for NAND booting is option F for 2k page devices. So to boot from a 512 bype page device, the I2C bootstrap EEPROM needs to be programmed accordingly. This patch adds basic NAND booting support for the AMCC Canyonlands aval board and also adds support to the "bootstrap" command, to enable NAND booting I2C setting. Tested with 512 byte page NAND device (32MByte) on Canyonlands. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Add basic support for AMCC 460EX/460GT (2/5)Stefan Roese2008-03-15-7/+178
| | | | | | This patch adds basic support for the AMCC 460EX/460GT PPC's. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Add basic support for AMCC 460EX/460GT (1/5)Stefan Roese2008-03-15-93/+553
| | | | | | This patch adds basic support for the AMCC 460EX/460GT PPC's. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: interrupt.c reworkedStefan Roese2008-03-15-448/+141
| | | | | | | | This patch is a rework of the 4xx interrupt handling done while adding the 460EX/GT support. Interrupts are needed on 4xx for the EMAC driver. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: program_tlb now uses 64bit physical addessStefan Roese2008-03-15-13/+14
| | | | | | | | This patch changes the physical addess parameter from 32bit to 64bit. This is needed for 36bit 4xx platforms to access areas located beyond the 4GB border, like SoC peripherals (EBC etc.). Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: miiphy.c reworkedStefan Roese2008-03-15-116/+80
| | | | | | | While adding the 460EX/GT support I reworked the 4xx miiphy code. It badly neede some cleanup. Signed-off-by: Stefan Roese <sr@denx.de>
* PPC4xx (Sequoia): Fix Ethernet "remote fault" problemsMike Nuss2008-03-04-3/+2
| | | | | | | | | | | | | | Every now and then a Sequoia board (or equivalent hardware) had problems connecting to a Gigabit capable network interface. There were differences in the PHY setup between Linux and U-Boot. This patch fixes the problem. Apparently "remote fault" is being set, which signals to some devices (on the other end of the cable) that a fault has occurred, while other devices ignore it. I believe the RF bit was causing the issue, but I removed T4 also, to match up with Linux. Signed-off-by: Mike Nuss <mike@terascala.com>
* ppc4xx: EMAC: Fix 405EZ fifo size setup in EMAC_MR1Stefan Roese2008-03-02-2/+3
| | | | | | | | | The 405EZ only supports 512 bytes of rx-/tx-fifo EMAC sizes. But currently 4k/2k is configured. This patch fixes this issue. Thanks to Thomas Kindler <tkindler@lenord.de> for pointing this out. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Fix problem in 4xx_enet.c driverAnatolij Gustschin2008-03-02-1/+9
| | | | | | | | | | U-Boot crashes in the net loop if CONFIG_4xx_DCACHE is enabled. To reproduce the problem ensure that 'ethrotate' environment variable isn't set to "no" and then run "tftp 200000 not_existent_file". This patch tries to fix the issue. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* cpu/ppc4xx/config.mk: Make a needlessly deffered expansion immediate.Shinya Kuribayashi2008-02-23-1/+1
| | | | | | This will reduce the build time. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
* Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xxWolfgang Denk2008-02-15-5/+9
|\
| * ppc4xx: Add CONFIG_4xx_DCACHE compile switch to Denali-core SPD codeLarry Johnson2008-02-14-3/+3
| | | | | | | | Signed-off-by: Larry Johnson <lrj@acm.org>
| * ppc4xx: Fix ndfc HW ECC byte orderStefan Roese2008-02-04-2/+2
| | | | | | | | | | | | | | | | | | | | | | The current ndfc HW ECC implementation swaps the first two ECC bytes. But the 4xx NDFC already uses the SMC (Smart Media Card) ECC ordering, so this swapping in the HW ECC driver is bogus. This patch fixes this problem and now really uses the SMC ECC byte order. Thanks to Sean MacLennan for pointing this out. Signed-off-by: Stefan Roese <sr@denx.de>
| * ppc4xx: Fix problem with init-ram bigger than 4k on 440 platformsStefan Roese2008-02-04-0/+4
| | | | | | | | Signed-off-by: Stefan Roese <sr@denx.de>
* | PPC: Use r2 instead of r29 as global data pointerWolfgang Denk2008-02-14-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | R29 was an unlucky choice as with recent toolchains (gcc-4.2.x) gcc will refuse to use load/store multiple insns; instead, it issues a list of simple load/store instructions upon function entry and exit, resulting in bigger code size, which in turn makes the build for a few boards fail. Use r2 instead. Signed-off-by: Wolfgang Denk <wd@denx.de>
* | ppc: Refactor cache routines, so there is only one common set.Rafal Jaworowski2008-02-14-33/+0
|/ | | | Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
* ppc4xx: Remove compiler warning in cpu/ppc4xx/44x_spd_ddr2.cStefan Roese2008-01-15-2/+2
| | | | Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Fix dflush() to restore DVLIM registerLarry Johnson2008-01-10-0/+2
| | | | Signed-off-by: Larry Johnson <lrj@acm.org>
* fix comments with new drivers organizationMarcel Ziswiler2008-01-09-1/+1
| | | | Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
* Merge branch 'lwmon5-no-ocm'Stefan Roese2008-01-09-1/+65
|\
| * ppc4xx: Add CFG_POST_ALT_WORD_ADDR to support non OCM POST WORD storageStefan Roese2008-01-09-1/+13
| | | | | | | | | | | | | | | | | | | | The privious 4xx POST implementation only supported storing the POST WORD in OCM. Since we need to reserve the OCM on LWMON5 for the logbuffer we need to store the POST WORD in some other non volatile location. This patch adds CFG_POST_ALT_WORD_ADDR to specify an address for such a location. Signed-off-by: Stefan Roese <sr@denx.de>
| * ppc4xx: Add 44x cache locking to better support init-ram in d-cacheStefan Roese2008-01-09-0/+52
| | | | | | | | | | | | | | | | | | | | | | This patch adds support for locking the init-ram/stack in d-cache, so that other regions may use d-cache as well Note, that this current implementation locks exactly 4k of d-cache, so please make sure that you don't define a bigger init-ram area. Take a look at the lwmon5 440EPx implementation as a reference. Signed-off-by: Stefan Roese <sr@denx.de>
* | ppc4xx: Move cpu/ppc4xx/vecnum.h into include pathMatthias Fuchs2008-01-09-408/+5
| | | | | | | | | | | | | | This patch allows the use of 4xx interrupt vector number defines in board specific code outside cpu/ppc4xx. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
* | ppc4xx: Fix UIC2 vector number baseMatthias Fuchs2008-01-09-16/+16
| | | | | | | | Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
* | ppc4xx: Return 0 on success in 4xx ethernet driverStefan Roese2008-01-08-2/+3
| | | | | | | | Signed-off-by: Stefan Roese <sr@denx.de>
* | ppc4xx: Remove weak binding from common Denali data-eye search codeLarry Johnson2008-01-05-7/+0
| | | | | | | | | | | | | | | | Now that there are no board-specific versions of "denali_core_search_data_eye()", the weak binding on the common version can be removed. Signed-off-by: Larry Johnson <lrj@acm.org>
* | Merge branch 'katmai-ddr-gda'Stefan Roese2008-01-05-59/+37
|\ \
| * | ppc4xx: Remove unused CONFIG_ECC_ERROR_RESET from 44x_spd_ddr2.cStefan Roese2008-01-05-44/+0
| | | | | | | | | | | | Signed-off-by: Stefan Roese <sr@denx.de>
| * | ppc4xx: Update Katmai/44x_spd_ddr2.c code for optimal DDR2 setupStefan Roese2008-01-05-15/+37
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | On Katmai the complete auto-calibration somehow doesn't seem to produce the best results, meaning optimal values for RQFD/RFFD. This was discovered by GDA using a high bandwidth scope, analyzing the DDR2 signals. GDA provided a fixed value for RQFD, so now on Katmai "only" RFFD is auto-calibrated. This patch also adds RDCC calibration as mentioned on page 7 of the AMCC PowerPC440SP/SPe DDR2 application note: "DDR1/DDR2 Initialization Sequence and Dynamic Tuning" Signed-off-by: Stefan Roese <sr@denx.de>
* | ppc4xx: Add functionality to GPIO supportLawrence R. Johnson2008-01-04-23/+40
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch makes two additions to GPIO support: First, it adds function gpio_read_in_bit() to read the a bit from the GPIO Input Register (GPIOx_IR) in the same way that function gpio_read_out_bit() reads a bit from the GPIO Output Register (GPIOx_OR). Second, it modifies function gpio_set_chip_configuration() to provide an additional option for configuring the GPIO from the "CFG_4xx_GPIO_TABLE". According to the 440EPx User's Manual, when an alternate output is used, the three-state control is configured in one of two ways, depending on the particular output. The first option is to select the corresponding alternate three-state control in the GPIOx_TRSH/L registers. The second option is to select the GPIO Three-State Control Register (GPIOx_TCR) in the GPIOx_TRSH/L registers, and set the corresponding bit in the GPIOx_TCR register to enable the output. For example, the Manual specifies configuring the GPIO00 Alternate 1 Signal (PreAddr07) to use the alternate three-state control (first option), and specifies configuring the GPIO32 Alternate 1 Signal (USB2OM0) with the output enabled in the GPIOx_TCR register (second option). Currently, gpio_set_chip_configuration() configures all alternate signal outputs to use the first option. This patch allow the second option to be selected by setting the "out_val" element in the table entry to "GPIO_OUT_1". The first option is used when the "out_val" element is set to "GPIO_OUT_0". Because "out_val" is not currently used when an alternate signal is selected, and because all current GPIO tables set "out_val" to "GPIO_OUT_0" for all alternate signals, this patch should not change any existing configurations. Signed-off-by: Larry Johnson <lrj@acm.org>
generated by cgit v1.1 at 2024-11-16 18:17:11 +0000