| Commit message (Collapse) | Author | Age | Lines |
|---|
| |
|
|
| |
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
| |
|
|
| |
Signed-off-by: Stefan Roese <sr@denx.de>
|
| |
|
|
|
|
|
|
| |
This patch adds GPCS, SGMII and M88E1112 PHY support
for the AMCC PPC460GT/EX processors.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
| |
|
|
|
|
|
| |
While adding the 460EX/GT support I reworked the 4xx miiphy code. It
badly neede some cleanup.
Signed-off-by: Stefan Roese <sr@denx.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Every now and then a Sequoia board (or equivalent hardware) had
problems connecting to a Gigabit capable network interface.
There were differences in the PHY setup between Linux and U-Boot.
This patch fixes the problem. Apparently "remote fault" is being set,
which signals to some devices (on the other end of the cable) that a
fault has occurred, while other devices ignore it. I believe the RF bit
was causing the issue, but I removed T4 also, to match up with Linux.
Signed-off-by: Mike Nuss <mike@terascala.com>
|
| |
|
|
|
|
|
|
|
|
| |
This patch adds a new switch: "CONFIG_PHY_DYNAMIC_ANEG". When this symbol
is defined, the PHY will advertise it's capabilities for autonegotiation
based on the capabilities shown in the PHY's status registers, including
1000BASE-X. When "CONFIG_PHY_DYNAMIC_ANEG" is not defined, the PHY will
advertise hard-coded capabilities, as before.
Signed-off-by: Larry Johnson <lrj@acm.org>
|
| |
|
|
|
|
|
| |
This patch changes all in32/out32 calls to use the recommended in_be32/
out_be32 macros instead.
Signed-off-by: Stefan Roese <sr@denx.de>
|
| |
|
|
| |
Signed-off-by: Stefan Roese <sr@denx.de>
|
| |
|
|
|
|
|
|
|
|
|
| |
- Add support for PPC440EPx & PPC440GRx
- Add support for PPC440EP(x)/GR(x) NAND controller
in cpu/ppc4xx directory
- Add NAND boot functionality for Sequoia board,
please see doc/README.nand-boot-ppc440 for details
- This Sequoia NAND image doesn't support environment
in NAND for now. This will be added in a short while.
Patch by Stefan Roese, 07 Sep 2006
|
| | |
|
| |
|
|
| |
Patch by John Otken, 23 Nov 2005
|
| | |
|
| |
|
|
|
| |
now handling all 4xx cpu's.
Patch by Stefan Roese, 16 Aug 2005
|
| | |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Allow bzip2 compression for small memory footprint boards
* Patch by Brad Kemp, 21 Jan 2004:
Add support for CFI flash driver for both the Intel and the AMD
command sets.
* Patch by Travis Sawyer, 20 Jan 2004:
Fix pci bridge auto enumeration of sibling p2p bridges.
* Patch by Tolunay Orkun, 12 Jan 2004:
Add some delays as needed for Intel LXT971A PHY support
* Patches by Stephan Linz, 09 Jan 2004:
- avoid warning: unused variable `piop' in board/altera/common/sevenseg.c
- make DK1C20 board configuration related to ASMI conform to
documentation
|
| |
|
|
|
|
|
| |
Add support for IBM PPC440GX. Multiple EMAC Ethernet devices,
select MDI port based on enabled EMAC device.
Add support for XES Inc <http://www.xes-inc.com> XPedite1000 440GX
base PrPMC board.
|
| | |
|
| | |
|
| |
|
|
|
|
|
| |
* Add support for P3G4 board
* Fix problem with MGT5100 FEC driver: add "early" MAC address
initialization
|
| |
|
|
|
|
|
|
|
| |
- remove trailing white space, trailing empty lines, C++ comments, etc.
- split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)
* Patches by Kenneth Johansson, 25 Jun 2003:
- major rework of command structure
(work done mostly by Michal Cendrowski and Joakim Kristiansen)
|
| | |
|
| |
|
