summaryrefslogtreecommitdiff
path: root/cpu/mpc83xx/cpu_init.c
Commit message (Collapse)AuthorAgeLines
* rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD2008-10-18-101/+101
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* mpc83xx: Store and display Arbiter Event Register valuesNick Spence2008-09-03-1/+135
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Record the Arbiter Event Register values and optionally display them. The Arbiter Event Register can record the type and effective address of an arbiter error, even through an HRESET. This patch stores the values in the global data structure. Display of the Arbiter Event registers immediately after the RSR value can be enabled with defines. The Arbiter values will only be displayed if an arbiter event has occured since the last Power On Reset, and either of the following defines exist: #define CONFIG_DISPLAY_AER_BRIEF - display only the arbiter address and and type register values #define CONFIG_DISPLAY_AER_FULL - display and interpret the arbiter event register values Address Only transactions are one of the trapped events that can register as an arbiter event. They occur with some cache manipulation instructions if the HID0_ABE (Address Broadcast Enable) is set and the memory region has the MEMORY_COHERENCE WIMG bit set. Setting: #define CONFIG_MASK_AER_AO - prevents the arbiter from recording address only events, so that it can still capture other real problems. Signed-off-by: Nick Spence <nick.spence@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* MPC83XX: Fix GPIO configuration - set gpio level before directionNick Spence2008-09-03-2/+2
| | | | | | | | | | | | | | | | | | | Set DAT value before DIR values to avoid creating glitches on the GPIO signals. Set gpio level register before direction register to inhibit glitches on high level output pins. Dir and data gets cleared at powerup, so high level output lines see a short low pulse between setting the direction and level registers. Issue was seen on a new board with the nReset line of the NOR flash connected to a GPIO. Setting the direction register puts the NOR flash in reset so the next instruction to set the level cannot get executed. Signed-off-by: Nick Spence <nick.spence@freescale.com> Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* fix system config overwrite @ MPC834x and MPC8313Andre Schwarz2008-06-25-0/+5
| | | | | | | | | | | | | | | | During 83xx setup the "System I/O configuration register high" gets overwritten with user defined value if CFG_SICRH is defined. Regarding to the MPC834x manual (Table 5-28 reve.1) bits 28+29 of SICRH must keep their reset value regardless of configuration. On my board (using RGMII) those bits are set after reset - yet it's unclear where they come from. The patch keeps both bits on MPC834x and MPC8313. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Big white-space cleanup.Wolfgang Denk2008-05-21-1/+1
| | | | | | | | | | | This commit gets rid of a huge amount of silly white-space issues. Especially, all sequences of SPACEs followed by TAB characters get removed (unless they appear in print statements). Also remove all embedded "vim:" and "vi:" statements which hide indentation problems. Signed-off-by: Wolfgang Denk <wd@denx.de>
* mpc8323erdb: Improve the system performanceMichael Barkowski2008-03-25-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following changes are based on kernel UCC ethernet performance: 1. Make the CSB bus pipeline depth as 4, and enable the repeat mode 2. Optimize transactions between QE and CSB. Added CFG_SPCR_OPT switch to enable this setting. The following changes are based on the App Note AN3369 and verified to improve memory latency using LMbench: 3. CS0_CONFIG[AP_n_EN] is changed from 1 to 0 4. CS0_CONFIG[ODT_WR_CONFIG] set to 1. Was a reserved setting previously. 5. TIMING_CFG_1[WRREC] is changed from 3clks to 2clks (based on Twr=15ns, and this was already the setting in DDR_MODE) 6. TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on Trp=15ns) 7. TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on Tras=40ns) 8. TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on Trcd=15ns) 9. TIMING_CFG_1[REFREC] changed from 21 clks to 11clks. (based on Trfc=75ns) 10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks. (based on Tfaw=50ns) 11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based on CL=3 and WL=2). Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Fix the fatal conflict of mergeDave Liu2008-01-17-6/+1
| | | | | | | | | | | | The commit 9e89647889cd4b5ada5b5e7cad6cbe55737a08d7 will cause the mpc8315erdb board can't boot up. The patch fix that bug, and remove the duplicated #ifdef CFG_SPCR_TSECEP code and clean the SCCR_TSEC2 for MPC8313E processor. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: add support for more system clock performance controlsKim Phillips2008-01-16-22/+51
| | | | | | | | | | System registers that are modified are the Arbiter Configuration Register (ACR), the System Priority Control Register (SPCR), and the System Clock Configuration Register (SCCR). Signed-off by: Michael F. Reiss <Michael.F.Reiss@freescale.com> Signed-off by: Joe D'Abbraccio <ljd015@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Add config of eTSEC emergency priority in SPCRDave Liu2008-01-16-0/+5
| | | | | | | | | | | The TSEC emergency priority definition of 831x/837x is different than the definition of 834x in SPCR register. Add the other config of TSEC emergency priority into cpu_init.c Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Add the support of MPC837xEMDS boardDave Liu2008-01-08-1/+5
| | | | | | | | | | | The MPC837xEMDS board support: * DDR2 400MHz hardcoded and SPD init * Local bus NOR Flash * I2C, UART, MII and RTC * eTSEC RGMII * PCI host Signed-off-by: Dave Liu <daveliu@freescale.com>
* mpc83xx: Add support for the display of reset statusDave Liu2007-08-10-0/+36
| | | | | | | | | | | | | 83xx processor family has many reset sources, such as power on reset, software hard reset, software soft reset, JTAG, bus monitor, software watchdog, check stop reset, external hard reset, external software reset. sometimes, to figure out the fault of system, we need to know the cause of reset early before the prompt of u-boot present. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Update SCCR programming in cpu_init_f() to support all 83xx processorsTimur Tabi2007-08-10-2/+12
| | | | | | | | | | | | | Update the cpu_init_f() function in cpu/mpc83xx/cpu_init.c to program the bitfields for all 83xx processors. The code to update some bitfields was compiled only on some processors. Now, the bitfields are programmed as long as the corresponding CFG_SCCR option is defined in the board header file. This means that the board header file should not define any CFG_SCCR macros for bitfields that don't exist on that processor, otherwise the SCCR will be programmed incorrectly. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Fix config of Arbiter, System Priority, and Clock ModeKumar Gala2007-03-02-6/+28
| | | | | | | | | | | | | | | | | | | | | | | | | The config value for: * CFG_ACR_PIPE_DEP * CFG_ACR_RPTCNT * CFG_SPCR_TSEC1EP * CFG_SPCR_TSEC2EP * CFG_SCCR_TSEC1CM * CFG_SCCR_TSEC2CM Were not being used when setting the appropriate register Added: * CFG_SCCR_USBMPHCM * CFG_SCCR_USBDRCM * CFG_SCCR_PCICM * CFG_SCCR_ENCCM To allow full config of the SCCR. Also removed random CFG_SCCR settings in MPC8349EMDS, TQM834x, and sbc8349 that were just bogus. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc83xx: Add support for the MPC832XEMDS boardDave Liu2007-03-02-0/+5
| | | | | | This patch supports DUART, ETH3/4 and PCI etc. Signed-off-by: Dave Liu <daveliu@freescale.com>
* mpc83xx: streamline the 83xx immr head fileDave Liu2007-03-02-4/+4
| | | | | | | | | | | | | | | | For better format and style, I streamlined the 83xx head files, including immap_83xx.h and mpc83xx.h. In the old head files, 1) duplicated macro definition appear in the both files; 2) the structure of QE immr is duplicated in the immap_83xx.h and immap_qe.h; 3) The macro definition put inside the each structure. So, I cleaned up the structure of QE immr from immap_83xx.h, deleted the duplicated stuff and moved the macro definition to mpc83xx.h, Just like MPC8260. CHANGELOG *streamline the 83xx immr head file Signed-off-by: Dave Liu <daveliu@freescale.com>
* mpc83xx: Miscellaneous code style fixesTimur Tabi2006-11-28-5/+0
| | | | | | Implement various code style fixes and similar changes. Signed-off-by: Timur Tabi <timur@freescale.com>
* mpc83xx: Replace CFG_IMMRBAR with CFG_IMMRTimur Tabi2006-11-03-1/+1
| | | | | | | Replace all instances of CFG_IMMRBAR with CFG_IMMR, so that the 83xx tree matches the other 8xxx trees. Signed-off-by: Timur Tabi <timur@freescale.com>
* mpc83xx: add QE ethernet supportDave Liu2006-11-03-6/+34
| | | | this patch adds support for the QUICC Engine based UCC gigabit ethernet device.
* mpc83xx: Add support for the MPC8349E-mITXTimur Tabi2006-11-03-0/+31
| | | | | | | | | | | | | | | | | | | PREREQUISITE PATCHES: * This patch can only be applied after the following patches have been applied: 1) DNX#2006090742000024 "Add support for multiple I2C buses" 2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x" 3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c" 4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems" 5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems" CHANGELOG: * Add support for the Freescale MPC8349E-mITX reference design platform. The second TSEC (Vitesse 7385 switch) is not supported at this time. Signed-off-by: Timur Tabi <timur@freescale.com>
* GCC-4.x fixes: clean up global data pointer initialization for all boards.Wolfgang Denk2006-03-31-2/+2
|
* Decopuled setting of OR/BR and LBLAWBAR/LBLAWAR on MPC83xxKumar Gala2006-01-25-28/+21
| | | | Patch by Kumar Gala, 25 Jan 2006
* Allow config of GPIO direction & data registers at boot on 83xxKumar Gala2006-01-11-0/+8
| | | | Patch by Kumar Gala, 11 Jan 2006
* Make System IO Config Registers board configurable on MPC83xxKumar Gala2006-01-11-2/+6
| | | | Patch by Kumar Gala, 11 Jan 2006
* Fix style issues primarily in 85xx and 83xx boards.Jon Loeliger2005-08-01-1/+0
| | | | | | | | - C++ comments - Trailing white space - Indentation not by TAB - Excessive amount of empty lines - Trailing empty lines
* * Patch by Eran LibertyEran Liberty2005-07-28-0/+164
Add support for the Freescale MPC8349ADS board.
generated by cgit v1.1 at 2024-12-20 09:20:54 +0000