summaryrefslogtreecommitdiff
path: root/cpu/arm926ejs
Commit message (Collapse)AuthorAgeLines
* at91: Introduction of at91sam9g10 SOC.Sedji Gaouaou2009-07-12-0/+1
| | | | | | | AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a faster clock speed: 266/133MHz. Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
* at91: Introduction of at91sam9g45 SOC.Sedji Gaouaou2009-07-12-2/+187
| | | | | | | | | | | | AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz. It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of peripherals. The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES. On the board you can find 2 USART, USB high speed, a 480*272 LG lcd, ethernet, gpio/joystick/buttons. Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
* Coding style cleanup; update CHANGELOGWolfgang Denk2009-07-07-3/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* arm: Kirkwood: arch specific updated for ehci-Kirkwood driver supportPrafulla Wadaskar2009-07-06-5/+1
| | | | | | This patch abstracts Kirkwood arch specific changes to support ehci-kirkwood driver Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* arm nomadik: use 1000 as HZ value and rewrite timer codeAlessandro Rubini2009-07-06-139/+27
| | | | | | | | | | | | This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites timer code, which is now both correct and much smaller. Unused functions like udelay_masked() have been removed as no driver uses them, even the ones that are not currently active for this board. mtu.h is copied literally from the kernel sources. Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stericsson.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm nomadik: cleanup resetAlessandro Rubini2009-07-06-12/+1
| | | | | | | | There is only one public release of the Nomadik chip, so the ifdef in reset code as well as a define in the config file are not needed Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
* at91: Add CAN init functionDaniel Gorsulowski2009-07-06-0/+30
| | | | | | | | | To enable CAN init, CONFIG_CAN has to be defined in the board config file and at91_can_hw_init() has to be called in the board specific code. CAN is available on AT91SAM9263 and AT91CAP9 SoC. Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
* arm: Kirkwood: Basic SOCs supportPrafulla Wadaskar2009-07-06-0/+670
| | | | | | | | | | | | | | | | | | | | | | Kirkwood family controllers are highly integrated SOCs based on Feroceon-88FR131/Sheeva-88SV131/arm926ejs cpu core. SOC versions supported:- 1) 88F6281-A0 define CONFIG_KW88F6281_A0 2) 88F6192-A0 define CONFIG_KW88F6192_A0 Other supported features:- 1) get_random_hex() fucntion 2) PCI Express port initialization 3) NS16550 driver support Contributors: Yotam Admon <yotam@marvell.com> Michael Blostein <michaelbl@marvell.com Reviewed-by: Ronen Shitrit <rshitrit@marvell.com> Acked-by: Stefan Rose <sr@denx.de> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* mx27: basic cpu supportIlya Yanok2009-06-21-0/+533
| | | | | | This patch adds generic code to support Freescale's i.MX27 SoCs. Signed-off-by: Ilya Yanok <yanok@emcraft.com>
* at91: unify nor boot supportJean-Christophe PLAGNIOL-VILLARD2009-06-21-2/+284
| | | | | | the lowlevel init sequence is the same so unify it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Switched davinci_emac Ethernet driver to use newer APIBen Warren2009-06-15-0/+12
| | | | | | | | Added CONFIG_NET_MULTI to all Davinci boards Removed all calls to Davinci network driver from board code Added cpu_eth_init() to cpu/arm926ejs/cpu.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Moved Davinci Ethernet driver to drivers/netBen Warren2009-06-15-656/+1
| | | | | | This driver has been renamed davinci_emac.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* at91: move cpu info print to cpuJean-Christophe PLAGNIOL-VILLARD2009-06-12-5/+22
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91: extract reset from timerJean-Christophe PLAGNIOL-VILLARD2009-06-12-15/+43
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: remove cpu_initJean-Christophe PLAGNIOL-VILLARD2009-06-12-5/+0
| | | | | | move s3c44b0 to arch_cpu_init and as noone use cpu_init remove it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: unify interrupt initJean-Christophe PLAGNIOL-VILLARD2009-06-12-11/+0
| | | | | | | all arm init the IRQ stack the same way so unify it in lib_arm/interrupts.c and then call arch specific interrupt init Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: unify linker scriptJean-Christophe PLAGNIOL-VILLARD2009-06-12-65/+9
| | | | | | | | | | | | all arm boards except a few use the same cpu linker script so move it to cpu/$(CPU) that could be overwrite in following order SOC BOARD via the corresponding config.mk Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* afeb9260: fix macb device initJean-Christophe PLAGNIOL-VILLARD2009-06-12-1/+1
| | | | | | uses PA10, PA11 for ETX2 and ETX3. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM DaVinci: Reset with watchdog enabledThomas Lange2009-06-12-0/+4
| | | | | | | | | Once the Davinci watchdog has been enabled, the timeout value cannot be changed. If the timeout in use is long, it can take a long time for card to reset. By writing an invalid service key, we can trigger an immediate reset. Signed-off-by: Thomas Lange <thomas@corelatus.se>
* at91: regroup IP hw init in one file per socJean-Christophe PLAGNIOL-VILLARD2009-06-12-603/+338
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM DaVinci:Consolidate common u-boot.ldsSandeep Paulraj2009-06-12-0/+89
| | | | | | | | | The u-boot.lds is common for all DaVinci boards. The patch removes multiple instances and moves the u-boot.lds to /cpu/arm926ejs/davinci folder. This addresses one of the comments i received while submitting patches for DM3xx Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* arm920/926/926: remove non needed headerJean-Christophe PLAGNIOL-VILLARD2009-06-12-6/+0
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* davinci: display correct clock infoDavid Brownell2009-06-12-1/+132
| | | | | | | | | | | | Move the clock-rate dumping code into the cpu/.../davinci area where it should have been, enabled by CONFIG_DISPLAY_CPUINFO, updating the format and showing the DSP clock (where relevant). Switch boards to use the cpuinfo() hook for this stuff. Remove a few now-obsolete PLL #defines. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* arm: timer and interrupt init reworkJean-Christophe PLAGNIOL-VILLARD2009-06-12-58/+1
| | | | | | | | | | | | | | actually the timer init use the interrupt_init as init callback which make the interrupt and timer implementation difficult to follow so now rename it as int timer_init(void) and use interrupt_init for interrupt btw also remane the corresponding file to the functionnality implemented as ixp arch implement two timer - one based on interrupt - so all the timer related code is moved to timer.c Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* davinci: add basic dm355/dm350/dm335 supportDavid Brownell2009-06-12-0/+46
| | | | | | | | | | | | | Add some basic declarations for DaVinci DM355/DM350/DM335 support, keyed on CONFIG_SOC_DM355. (DM35X isn't quite right because the DM357 is very different; while the DM355 is like a DM355 without the MPEG/JPEG coprocessor). These have different peripherals than the DM6446, and some of the peripherals are at different addresses. Notably for U-Boot, there's no EMAC, and the NAND controller address is different Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* davinci: fix dm644x bugletsDavid Brownell2009-06-12-1/+3
| | | | | | | | Fix two buglets in the dm644x support: don't set two must-be-zero bits in the UART management register; and only include the I2C hooks if the I2C driver is being included. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* davinci: split out some dm644x-specific bits from pscDavid Brownell2009-06-12-75/+123
| | | | | | | | | | | | | | Split out DaVinci DM6446-specific bits from more generic bits: - Add a CONFIG_SOC_DM644X. All current boards use DM6446 chips; DM6443 and DM6441 chips differ in available peripherals. - Move most DM644X-specific bits from psc.c to a new dm644x.c file, which is conditionally built. It provides device-specific setup. Plus minor coding style and comment updates with respect to the PSC. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* davinci: cpu-specific build uses conditional make syntaxDavid Brownell2009-06-12-3/+5
| | | | | | | | | | | Update cpu/arm926ejs/davinci/Makefile to use COBJ-y type syntax. Add the first conditional: for EMAC driver support. Not all chips have an EMAC; and boards might not use it, anyway. This doesn't touch PHY configuration; that should eventually become conditional too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* davinci: move psc support board-->cpuDavid Brownell2009-06-12-1/+183
| | | | | | | | Move DaVinci PSC support from board/* to cpu/* where it belongs. The PSC module manages clocks and resets for all DaVinci-family SoCs, and isn't at all board-specific. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* DaVinci now respects SKIP_LOWLEVEL_INITDavid Brownell2009-06-12-1/+5
| | | | | | | | Don't needlessly include lowlevel init code; that's only really needed with boot-from NOR (not boot-from-NAND). The 2nd stage loader (UBL) handles that before it loads U-Boot. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* at91/cpu.c: add missing Copyright & GPL headerJean-Christophe PLAGNIOL-VILLARD2009-06-10-0/+23
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Fix e-mail address of Gary Jennejohn.Detlev Zundel2009-05-15-11/+11
| | | | Signed-off-by: Detlev Zundel <dzu@denx.de>
* AFEB9260 network fixSergey Lapin2009-05-13-1/+1
| | | | | | | | AFEB9260 uses PA10, PA11 for ETX2 and ETX3. Also, due to extarnal pull-up on IRQ line, Micrel PHY ID is 1 after reset sequence, not 0. Signed-off-by: Sergey Lapin <slapin@ossfans.org>
* at91: remove lowlevel_init.SJean-Christophe PLAGNIOL-VILLARD2009-05-01-61/+2
| | | | | | | | | | | | lowlevel_init.S is not used any more so remove it. As consequence, we also don't have to generate u-boot.lds but can use a static version as before. This also fixes the out-of-tree build problem introduced with commit f0a2c7b4 "at91: add support for the PM9263 board" Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
* Update CHANGELOG; minor coding style cleanup.Wolfgang Denk2009-05-01-1/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* at91: fixed plla calc when no USB support is activeDaniel Gorsulowski2009-04-29-1/+1
| | | | | Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: fix CONFIG_SYS_HZ to 1000Jean-Christophe PLAGNIOL-VILLARD2009-04-16-38/+44
| | | | | | | | The timer has been rewrote with a precision at ~0,18% Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Tested-by: Sergey Lapin <slapin@ossfans.org> Tested-by: Eric BENARD <ebenard@free.fr>
* at91: add support for the PM9263 board of Ronetix GmbHIlko Iliev2009-04-16-4/+14
| | | | | | | | | | The PM9263 board is based on the AT91SAM9263-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9263.html Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: improve clock frameworkJean-Christophe PLAGNIOL-VILLARD2009-04-16-0/+218
| | | | | | calculate dynamically the clock rate and pllb setting for usb Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: unify reset commandJean-Christophe PLAGNIOL-VILLARD2009-04-05-8/+0
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: clean cache managementJean-Christophe PLAGNIOL-VILLARD2009-04-05-62/+10
| | | | | | unify arm cache management except for non standard cache as ARM7TDMI Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: update co-processor 15 accessJean-Christophe PLAGNIOL-VILLARD2009-04-05-57/+14
| | | | | | import system.h from linux Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91: move dataflash spi driver to drivers/spiJean-Christophe PLAGNIOL-VILLARD2009-04-04-158/+0
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91: move usb driver to drivers/usbJean-Christophe PLAGNIOL-VILLARD2009-04-04-81/+0
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91: rename DATAFLASH_MMC_SELECT to CONFIG_DATAFLASH_MMC_SELECTJean-Christophe PLAGNIOL-VILLARD2009-04-04-0/+5
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: spi init add hardware chip select supportJean-Christophe PLAGNIOL-VILLARD2009-04-04-27/+136
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* OMAP: rename timer divisorLadislav Michl2009-03-30-1/+1
| | | | | | | Divisor field is called PTV not PVT. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* davinci: move i2c driver to drivers/i2cJean-Christophe PLAGNIOL-VILLARD2009-03-30-335/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* davinci: move nand driver to drivers/mtd/nandJean-Christophe PLAGNIOL-VILLARD2009-03-30-476/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.Nicolas Ferre2009-03-22-2/+7
| | | | | | | | | | | | | | AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board. It is essentially the same, with a few minor differences. Here is the chip page on Atmel website: http://www.atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Justin Waters <justin.waters@timesys.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
generated by cgit v1.1 at 2024-07-17 12:46:10 +0000