summaryrefslogtreecommitdiff
path: root/configs
Commit message (Collapse)AuthorAgeLines
* defconfigs: engicam: Enable UBI commandsJagan Teki2017-01-02-0/+3
| | | | | | | | | | | | | | | | | | | | | | Create ubifs.img: $ mkfs.ubifs -q -r /rootfs -m 4096 -e 253952 -c 7936 -o ubifs.img Write ubifs.img: --------------- icorem6qdl> nand erase.part rootfs icorem6qdl> ubi part rootfs icorem6qdl> ubi create rootfs icorem6qdl> ext4load mmc 0:2 ${loadaddr} ubifs.img 166592512 bytes read in 8091 ms (19.6 MiB/s) icorem6qdl> ubi write ${loadaddr} rootfs ${filesize} 166592512 bytes written to volume rootfs icorem6qdl> ubifsmount ubi0:rootfs Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* defconfigs: engicam: Enable MMC commands in nandJagan Teki2017-01-02-0/+15
| | | | | | | | | | | For writing Linux or rootfs on to NAND, the best suitable way is to use MMC commands since MMC driver by default enabled by mx6_common.h, hence enabled MMC commands in nand defconfigs. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: engicam: Use bootm instead of bootzJagan Teki2017-01-02-8/+0
| | | | | | | | | | Boot Linux with uImage instead of zImage, so update bootz with bootm. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* ARM: imx7s-warp: enable USB gadget ethernetKevin Hilman2017-01-02-0/+5
| | | | | | | | | Enable USB gadget ethernet by default to have networking capabilities. Tested using DHCP and TFTP to transfer kernel, DT, ramdisk. Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
* mmc: move some SDHCI related options to KconfigMasahiro Yamada2016-12-29-0/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While I moved the options, I also renamed them so that they are all prefixed with MMC_SDHCI_. This commit was created in the following steps. [1] Rename with the following command find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e ' s/CONFIG_MMC_SDMA/CONFIG_MMC_SDHCI_SDMA/g s/CONFIG_BCM2835_SDHCI/CONFIG_MMC_SDHCI_BCM2835/g s/CONFIG_KONA_SDHCI/CONFIG_MMC_SDHCI_KONA/g s/CONFIG_MV_SDHCI/CONFIG_MMC_SDHCI_MV/g s/CONFIG_S5P_SDHCI/CONFIG_MMC_SDHCI_S5P/g s/CONFIG_SPEAR_SDHCI/CONFIG_MMC_SDHCI_SPEAR/g ' [2] create the Kconfig entries in drivers/mmc/Kconfig [3] Move the options by the following command tools/moveconfig.py -y MMC_SDHCI_SDMA MMC_SDHCI_BCM2835 \ MMC_SDHCI_KONA MMC_SDHCI_MV MMC_SDHCI_S5P MMC_SDHCI_SPEAR [4] Sort drivers/mmc/Makefile for readability Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: move CONFIG_SDHCI to Kconfig, renaming to CONFIG_MMC_SDHCIMasahiro Yamada2016-12-29-0/+54
| | | | | | | | | | | | | | | | | | | | | | | Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI. My motivation for the rename is, ultimately, to make all the MMC options prefixed with MMC_ and SDHCI options with MMC_SDHCI_, like Linux. This commit was created as follows: [1] Rename the config option with the following command: find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g' [2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig [3] run "tools/moveconfig.py -y MMC_SDHCI" [4] add "depends on MMC_SDHCI" to existing SDHCI driver entries Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: make MMC driver entries dependent on MMCMasahiro Yamada2016-12-29-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, CONFIG_MMC is not related to any other options by "depends on" or "select". One of big advantages of using Kconfig is automatic dependency tracking, but the current state is lacking it. As the first step, make the existing MMC driver entries depend on MMC. This commit was created by the following steps: [1] Run the following script: --------------------8<-------------------- rm -f tmp.txt for d in $(find . -path './configs/*_defconfig') do if grep -q -e 'CONFIG_MSM_SDHCI=y' $d || grep -q -e 'CONFIG_ATMEL_SDHCI=y' $d || grep -q -e 'CONFIG_ROCKCHIP_DWMMC=y' $d || grep -q -e 'CONFIG_SH_SDHI=y' $d || grep -q -e 'CONFIG_PIC32_SDHCI=y' $d || grep -q -e 'CONFIG_ZYNQ_SDHCI=y' $d || grep -q -e 'CONFIG_ROCKCHIP_SDHCI=y' $d || grep -q -e 'CONFIG_MMC_UNIPHIER=y' $d || grep -q -e 'CONFIG_SANDBOX_MMC=y' $d then echo CONFIG_MMC=y >> $d echo ${d#./configs/} >> tmp.txt fi done tools/moveconfig.py -y -s -d tmp.txt rm tmp.txt --------------------8<-------------------- [2] surround MMC driver entries with "if MMC" and "endif" Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: complete unfinished move of CONFIG_MMCMasahiro Yamada2016-12-29-2/+375
| | | | | | | | | | | | | | | | | | | | | | | | Commit 7a777f6d6f35 ("mmc: Add generic Kconfig option") created a Kconfig entry for this option without any actual moves, then commit 44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved instances only for SUNXI. We generally do not like such partial moves. This kind of work is automated by tools/moveconfig.py, so it is pretty easy to complete this move. I am adding "default ARM || PPC || SANDBOX" (suggested by Tom). This shortens the configs and will ease new board porting. This commit was created as follows: [1] Edit Kconfig (remove the "depends on", add the "default", copy the prompt and help message from Linux) [2] Run 'tools/moveconfig.py -y -s -r HEAD MMC' Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* Sync defconfig files by savedefconfigMasahiro Yamada2016-12-29-447/+310
| | | | | | | | Generated by "tools/moveconfig -s". This will make config moves easier. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini2016-12-23-9/+0
|\
| * spi: Zap armada100_spi.c and envJagan Teki2016-12-21-5/+0
| | | | | | | | | | | | | | | | armada100_spi.c and related env is zapping becuase of "no DM conversion". Cc: Ajay Bhargav <ajay.bhargav@einfochips.com> Signed-off-by: Jagan Teki <jagan@openedev.com>
| * spi: Zap mpc52xx_spi.c, config and related codeJagan Teki2016-12-21-4/+0
| | | | | | | | | | | | | | | | | | armada100_spi.c, related config options and related codes are zapping becuase of "no DM conversion". Cc: Werner Pfister <Pfister_Werner@intercontrol.de> Signed-off-by: Jagan Teki <jagan@openedev.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | configs: enable the DM_PMIC and DM_I2C_GPIO for max8998 pmicJaehoon Chung2016-12-22-0/+3
| | | | | | | | | | | | | | Enable the DM_PMIC and DM_I2C_GPIO for using max8998 pmic. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | block: Move ceva driver to DMMichal Simek2016-12-20-0/+6
|/ | | | | | | | | This patch also includes ARM64 zynqmp changes: - Remove platform non DM initialization - Remove hardcoded sata base address Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* imx6: icorem6_rqs: Add FEC supportJagan Teki2016-12-16-0/+6
| | | | | | | | | Add FEC support for Engicam i.CoreM6 RQS modules. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: geam6ul: Add FEC supportJagan Teki2016-12-16-0/+6
| | | | | | | | | Add FEC support for Engicam GEAM6UL module. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: icorem6_rqs: Add I2C supportJagan Teki2016-12-16-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add I2C support for Engicam i.CoreM6 RQS modules. icorem6qdl-rqs> i2c bus Bus 0: i2c@021a0000 Bus 1: i2c@021a4000 Bus 2: i2c@021a8000 icorem6qdl-rqs> i2c dev 0 Setting bus to 0 icorem6qdl-rqs> i2c speed 100000 Setting bus speed to 100000 Hz icorem6qdl-rqs> i2c probe Valid chip addresses: 4F icorem6qdl-rqs> i2c md 4F 0xff 00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ icorem6qdl-rqs> i2c bus Bus 0: i2c@021a0000 (active 0) 4f: generic_4f, offset len 1, flags 0 Bus 1: i2c@021a4000 Bus 2: i2c@021a8000 Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: icorem6: Rename engicam icorem6 defconfig filesJagan Teki2016-12-16-0/+89
| | | | | | | | | | Rename defconfig files for better compatible with respective board names and dts files. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* arm: imx6q: Add Engicam i.CoreM6 Solo/Duallite RQS Starter Kit initial supportJagan Teki2016-12-16-0/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from MMC: ------------- U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07) Trying to boot from MMC1 U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07 +0530) CPU: Freescale i.MX6DL rev1.3 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 DualLite/Solo RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl-rqs> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* arm: imx6q: Add Engicam i.CoreM6 Quad/Dual RQS Starter Kit initial supportJagan Teki2016-12-16-0/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from MMC: ------------- U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44) Trying to boot from MMC1 U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44 +0530) CPU: Freescale i.MX6D rev1.2 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl-rqs> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: geam6ul: Add NAND supportJagan Teki2016-12-16-0/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add NAND support for Engicam GEAM6UL board. Boot Log: -------- U-Boot SPL 2016.11-g537fa5f (Nov 28 2016 - 11:42:28) Trying to boot from NAND NAND : 256 MiB U-Boot 2016.11-g537fa5f (Nov 28 2016 - 11:20:06 +0100) CPU: Freescale i.MX6UL rev1.1 69 MHz (running at 396 MHz) CPU: Automotive temperature grade (-40C to 125C) at 42C Reset cause: WDOG Model: Engicam GEAM6UL DRAM: 128 MiB NAND: 256 MiB MMC: FSL_SDHC: 0 * Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: geam6ul: Add I2C supportJagan Teki2016-12-16-0/+2
| | | | | | | | | | | | | | | | | | | | | | | Add I2C support for Engicam GEAM6UL module. geam6ul> i2c bus Bus 0: i2c@021a0000 Bus 1: i2c@021a4000 geam6ul> i2c dev 0 Setting bus to 0 geam6ul> i2c dev Current bus is 0 geam6ul> i2c speed 100000 Setting bus speed to 100000 Hz geam6ul> i2c probe Valid chip addresses: 2C geam6ul> i2c md 2C 0xff 00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00 .......d........ Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* arm: imx6ul: Add Engicam GEAM6UL Starter Kit initial supportJagan Teki2016-12-16-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot Log: -------- U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30) Trying to boot from MMC1 U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530) CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 43C Reset cause: POR Model: Engicam GEAM6UL DRAM: 128 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 geam6ul> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: icorem6: Add I2C supportJagan Teki2016-12-16-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | Add I2C support for Engicam i.CoreM6 qdl board. icorem6qdl> i2c bus Bus 0: i2c@021a0000 Bus 1: i2c@021a4000 Bus 2: i2c@021a8000 icorem6qdl> i2c dev 2 Setting bus to 2 icorem6qdl> i2c speed 100000 Setting bus speed to 100000 Hz icorem6qdl> i2c probe Valid chip addresses: 2C icorem6qdl> i2c md 2C 0xff 00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00 .......d........ Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Heiko Schocher <hs@denx.de>
* imx6: icorem6: Add framebuffer supportJagan Teki2016-12-16-0/+6
| | | | | | | | | | Add IPUv3 framebuffer support for Engicam i.CoreM6 qdl board. Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* icorem6: Use CONFIG_DM_ETH supportJagan Teki2016-12-16-2/+0
| | | | | | | | | | | | Use CONFIG_DM_ETH and remove board_eth_init code from board files. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* arm: imx: add i.MX53 Beckhoff CX9020 Embedded PCPatrick Bruenn2016-12-16-0/+35
| | | | | | | | | | | | | | | | Add CX9020 board based on mx53loco. Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse serial_mxc with DTE and prepare for device tree migration of other functions and imx53 devices. The CX9020 differs from i.MX53 Quick Start Board by: - use uart2 instead of uart1 - DVI-D connector instead of VGA - no audio - CCAT FPGA connected to emi - enable rtc Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
* imx: mx6sllevk: add plugin supportPeng Fan2016-12-16-0/+37
| | | | | | | Add plugin support for mx6sllevk board. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* arm: imx: add i.MX6SLL EVK board supportPeng Fan2016-12-16-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add i.MX6SLL EVK board support. 1. Add imx6sll-evk device tree. 2. Enable SDHC/I2C/UART. 3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver. Boot Log: U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800) CPU: Freescale i.MX6SLL rev1.0 at 792MHz CPU: Commercial temperature grade (0C to 95C)Reset cause: POR Model: Freescale i.MX6SLL EVK Board Board: MX6SLL EVK DRAM: 2 GiB i2c bus 0 at 35258368, no gpio pinctrl state. PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* board/liteboard: Add support for liteBoardMarcin Niestroj2016-12-16-0/+29
| | | | | | | | | | | | liteBoard is a development board which uses liteSOM as its base. Hardware specification: * liteSOM (i.MX6UL, DRAM, eMMC) * Ethernet PHY (id 0) * USB host (usb_otg1) * MicroSD slot (uSDHC1) Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
* udoo_neo: Add Ethernet supportBreno Lima2016-12-16-1/+1
| | | | | | | | UDOO Neo boards has one FEC port connected to KSZ8091, add support for it. Tested on a UDOO Neo Full with "dhcp zImage" command. Signed-off-by: Breno Lima <breno.lima@nxp.com>
* udoo_neo: Move MX6SX configuration to KconfigBreno Lima2016-12-16-1/+1
| | | | | | | | | It's not necessary to define the processor in the defconfig file. The preferred method to select the SoC is via Kconfig file. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
* arm: imx: initial support for colibri imx6Max Krummenacher2016-12-16-0/+94
| | | | | | | | This adds board support for the Toradex module family Colibri iMX6. The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both with a version for commercial and industrial temperature range. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
* arm: imx: initial support for apalis imx6Max Krummenacher2016-12-16-0/+138
| | | | | | | | This adds board support for the Toradex module family Apalis iMX6. The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with commercial and industrial temperature range. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
* Merge git://www.denx.de/git/u-boot-marvellTom Rini2016-12-12-0/+9
|\
| * arm64: mvebu: Enable hush parser in A8K default configurationKonstantin Porotchkin2016-12-12-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable hush parser in Armada-7040 and Armada-8040 DB default configurations. Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
| * arm64: mvebu: Enable PCIe support in Armada-7040 configurationKonstantin Porotchkin2016-12-12-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable PCIe bus support in Armada-7040 DB default configuration Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
| * arm64: mvebu: Enable pin control support in A8K default configKonstantin Porotchkin2016-12-12-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable mvebu pin control support in the default configuration files for Armada-7040 and Armada-8040 development boards Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
| * arm64: mvebu: Enable BUBT command support in A8K default configKonstantin Porotchkin2016-12-12-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable mvebu "bubt" command support in the default configuration file for Armada-7040 and Armada-8040 development boards Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini2016-12-12-0/+6
|\ \
| * | ARM: uniphier: disable CONFIG_ARCH_FIXUP_FDT_MEMORYMasahiro Yamada2016-12-10-0/+6
| |/ | | | | | | | | | | | | Do not overwrite the memory nodes in the kernel DT where some parts of the memory region might be carved out. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | davinci: omapl138_lcdk: boot from zImageFabien Parent2016-12-09-0/+1
| | | | | | | | | | | | | | Stop booting legacy uImage and now boot zImage. Signed-off-by: Fabien Parent <fparent@baylibre.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | defconfigs: am57xx_hs_evm: Add default OPTEE load addressAndrew F. Davis2016-12-09-0/+3
| | | | | | | | | | | | | | | | | | Currently we let U-Boot find a spot at the end of DRAM at runtime, this forces us to build an OPTEE image based on the size of DRAM for an EVM. Add a default address that works across all current AM57xx EVMs. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | defconfigs: dra7xx_hs_evm: Add default OPTEE load addressAndrew F. Davis2016-12-09-0/+3
| | | | | | | | | | | | | | | | | | Currently we let U-Boot find a spot at the end of DRAM at runtime, this forces us to build an OPTEE image based on the size of DRAM for an EVM. Add a default address that works across all current DRA7xx EVMs. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | configs: omap5_uevm_defconfig: Enable LPAE modeKeerthy2016-12-09-0/+1
|/ | | | | | | | Enable Linear Physical Address Extension mode which is a prerequisite for hypervisor mode. Signed-off-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* Revert "Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze"Tom Rini2016-12-09-7/+0
| | | | | This reverts commit 3edc0c252257e4afed163a3a74aba24a5509b198, reversing changes made to bb135a0180c31fbd7456021fb9700b49bba7f533.
* Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini2016-12-09-0/+7
|\
| * travis-ci: Add zynq_zc702 target supportMichal Simek2016-12-08-0/+1
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Michal Simek <michal.simek@xilinx.com> Use embded option because of qemu Use my repo till Stephen merge it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * block: Move ceva driver to DMMichal Simek2016-12-08-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch also includes ARM64 zynqmp changes: - Remove platform non DM initialization - Remove hardcoded sata base address Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Series-to: sjg, agraf@suse.de Series-cc: uboot Series-version: 4 Series-changes: 2 - make ceva_init_sata static - Move SATA_CEVA to defconfig - Initalized max_lun and max_id platdata Series-changes: 3 - Extend Kconfig help description - sort dm.h - Remove SPL undefinition from board file - Fix Kconfig dependecies
* | socfpga: add support for Terasic DE1-SoC boardAnatolij Gustschin2016-12-06-0/+50
|/ | | | | | | | Add CycloneV based Terasic DE1-SoC board. The board boots from SD/MMC. Ethernet and USB host is supported. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Marek Vasut <marex@denx.de>
generated by cgit v1.1 at 2024-11-19 09:11:13 +0000