summaryrefslogtreecommitdiff
path: root/configs/crownbay_defconfig
Commit message (Collapse)AuthorAgeLines
* configs: Migrate CONFIG_USB_STORAGETom Rini2016-09-09-0/+1
| | | | | | | In some cases we were missing CONFIG_USB=y so enable that when needed. Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* x86: crownbay: Disable boot stage supportBin Meng2016-05-23-3/+0
| | | | | | | | | | | | | | | It is observed that when enabling boot stage support, occasionally the board reboots during boot over and over again, and eventually boots to shell. This was seen on my board, but not on Jian's board. Debugging shows that the TSC timer calibration against PIT fails as boot stage APIs utilize timer in a very early stage and at that time TSC/PIT may not be stable enough for the calibration to pass. Disable it for now. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Cc: Jian Luo <Jian.Luo4@boschrexroth.de> Reviewed-by: Simon Glass <sjg@chromium.org>
* configs: Re-sync with cmd/KconfigTom Rini2016-04-25-0/+6
| | | | | | | Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Re-sync almost all of cmd/KconfigTom Rini2016-04-25-0/+6
| | | | | | | | This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Re-sync HUSH optionsTom Rini2016-04-25-0/+1
| | | | | | | Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default. Signed-off-by: Tom Rini <trini@konsulko.com>
* x86: gpio: Allow the pinctrl driver to set up the pin configSimon Glass2016-03-17-0/+2
| | | | | | | | Rather than setting up the pin configuration in the GPIO driver, use the new pinctrl driver to do it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* Kconfig: Move CONFIG_FIT and related options to KconfigSimon Glass2016-03-14-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are already two FIT options in Kconfig but the CONFIG options are still in the header files. We need to do a proper move to fix this. Move these options to Kconfig and tidy up board configuration: CONFIG_FIT CONFIG_OF_BOARD_SETUP CONFIG_OF_SYSTEM_SETUP CONFIG_FIT_SIGNATURE CONFIG_FIT_BEST_MATCH CONFIG_FIT_VERBOSE CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_RSA Unfortunately the first one is a little complicated. We need to make sure this option is not enabled in SPL by this change. Also this option is enabled automatically in the host builds by defining CONFIG_FIT in the image.h file. To solve this, add a new IMAGE_USE_FIT #define which can be used in files that are built on the host but must also build for U-Boot and SPL. Note: Masahiro's moveconfig.py script is amazing. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Add microblaze change, various configs/ re-applies] Signed-off-by: Tom Rini <trini@konsulko.com>
* Correct defconfig orderingSimon Glass2016-03-14-2/+2
| | | | | | | | Various boards have the wrong Kconfig ordering now. To avoid a misleading diff in the next patch, reorder the configuration correctly. Signed-off-by: Simon Glass <sjg@chromium.org>
* vsprintf.c: Always enable CONFIG_SYS_VSNPRINTFTom Rini2016-01-19-1/+0
| | | | | | | | | | | | | | Enabling this function always removes some class of string saftey issues. The size change here in general is about 400 bytes and this seems a reasonable trade-off. Cc: Peng Fan <peng.fan@nxp.com> Cc: Peter Robinson <pbrobinson@gmail.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Adrian Alonso <aalonso@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* x86: Convert to use driver model timerBin Meng2015-12-01-0/+1
| | | | | | | Convert all x86 boards to use driver model tsc timer. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* sf: Move SPI flash drivers to defconfigBin Meng2015-11-25-0/+4
| | | | | | | | There are already Kconfig options for SPI flash drivers, but we have not moved them from config.h to defconfig files. This commit does this in a batch. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
* spi: Move SPI drivers to defconfigBin Meng2015-11-25-0/+1
| | | | | | | | There are already Kconfig options for SPI drivers, but we have not moved them from config.h to defconfig files. This commit does this in a batch. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
* ns16550: move CONFIG_SYS_NS16550 to KconfigThomas Chou2015-11-21-0/+1
| | | | | | Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py. Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
* common: add CMD_GPIO to KconfigThomas Chou2015-11-18-0/+1
| | | | | | | Add CMD_GPIO to Kconfig and run tools/moveconfig.py . Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Reviewed-by: Simon Glass <sjg@chromium.org>
* Reorder defconfigs with 'savedefconfig'Bin Meng2015-09-28-4/+4
| | | | | | Some boards' defconfigs are disordered. Reorder them. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
* x86: crownbay: Enable CONFIG_PCH_GBEBin Meng2015-09-09-0/+1
| | | | | | | | Now that we have converted the pch_gbe driver to driver moel, enable it on Intel Crown Bay board. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* x86: crownbay: Convert to use CONFIG_DM_ETH for E1000Bin Meng2015-09-09-1/+1
| | | | | | | | | Since E1000 driver has been converted to driver model, enable it on Intel Crown Bay. But the Intel Topcliff GbE driver has not been converted to driver model yet, disable it for now. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* x86: crownbay: Convert to use CONFIG_DM_USBBin Meng2015-09-09-0/+2
| | | | | | | | Move to driver model for USB on Intel Crown Bay. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Simon Glass <sjg@chromium.org>
* net: Move CONFIG_E1000 options to KconfigSimon Glass2015-08-21-0/+2
| | | | | | | | Move config for the E1000 Ethernet driver to Kconfig and tidy up affected boards. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* x86: Convert to use driver model pci on queensbay/crownbayBin Meng2015-07-28-0/+1
| | | | | | Move to driver model pci for Intel queensbay/crownbay. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Adjust config option order in defconfig for Crown Bay and MinnowmaxBin Meng2015-07-14-4/+4
| | | | | | | | Update crownbay_defconfig and minnowmax_defconfig with 'savedefconfig' result so that the config option order matches Kconfig. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* x86: crownbay: Enable graphics supportBin Meng2015-07-14-0/+3
| | | | | | | | | | | Enable graphics support on Intel Crown Bay board With the help of vgabios for Intel TunnelCreek IGD. Tested with an external LVDS panel connected to X4 connector and SDVO adapter connected to X9 connector on the board. Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* x86: crownbay: Enable writing MP tableBin Meng2015-07-14-0/+1
| | | | | | | Enable writing MP table for Intel Crown Bay board. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* x86: crownbay: Enable DM RTC supportBin Meng2015-07-14-0/+1
| | | | | | | Add a RTC node in the device tree to enable DM RTC support. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* x86: crownbay: Add MP initializationBin Meng2015-07-14-0/+4
| | | | | | | | | | | | Intel Crown Bay board has a TunnelCreek processor which supports hyper-threading. Add /cpus node in the crownbay.dts and enable the MP initialization. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> (modified to remove error: overriding the value of OF_CONTROL. Old value: "y", new value: "y")
* Move defaults from config_cmd_default.h to KconfigJoe Hershberger2015-06-25-1/+4
| | | | | | | | | | This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
* Move default y configs out of arch/board KconfigJoe Hershberger2015-06-25-0/+6
| | | | | | | | | | | | | | | | | | | Some archs/boards specify their own default by pre-defining the config which causes the Kconfig system to mix up the order of the configs in the defconfigs... This will cause merge pain if allowed to proliferate. Remove the configs that behave this way from the archs. A few configs still remain, but that is because they only exist as defaults and do not have a proper Kconfig entry. Those appear to be: SPIFLASH DISPLAY_BOARDINFO Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates, drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM] Signed-off-by: Tom Rini <trini@konsulko.com>
* net: Move the CMD_NET config to defconfigsJoe Hershberger2015-06-01-0/+1
| | | | | | | | | | | This also selects CONFIG_NET for any CONFIG_CMD_NET board. Remove the imx default for CONFIG_NET. This moves the config that was defined by 60296a8 (commands: add more command entries in Kconfig). Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
* Clean all defconfigs with savedefconfigJoe Hershberger2015-05-12-3/+2
| | | | | | | | | | | | | In order to reduce merge conflicts and to maintain the simplest possible defconfig files, we should be using the savedefconfig feature of Kconfig every time a new feature is added. This keeps the defconfig settings to a minimum (only those things not default) and keeps them in the same order as the Kconfig options. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Cc: Tom Rini <trini@konsulko.com>
* x86: Kconfig: Remove deprecated CONFIG_SYS_EXTRA_OPTIONSBin Meng2015-04-29-1/+0
| | | | | | | | | Currently all x86 boards still use CONFIG_SYS_EXTRA_OPTIONS to define the text base address. Since it is deprecated, just remove it and use CONFIG_SYS_TEXT_BASE directly. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* x86: Kconfig: Divide the target selection to vendor/modelBin Meng2015-04-29-0/+1
| | | | | | | | | | Let arch/x86/Kconfig prompt board vendor first, then select the board model under that vendor. This way arch/x86/Kconfig only needs concern board vendor and leave the supported target list to board/<vendor>/Kconfig. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* x86: queensbay: Implement PIRQ routingBin Meng2015-04-29-0/+1
| | | | | | | | Implement Intel Queensbay platform-specific PIRQ routing support. The chipset PIRQ routing setup is called in the arch_misc_init(). Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* x86: Add crownbay defconfig and config.hBin Meng2014-12-18-0/+6
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>