arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	configs: Re-sync with cmd/Kconfig	Tom Rini	2016-04-25	-0/+7
\| \| \| \| \| \| \|	Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
*	configs: Re-sync almost all of cmd/Kconfig	Tom Rini	2016-04-25	-0/+3
\| \| \| \| \| \| \| \|	This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
*	configs: Re-sync HUSH options	Tom Rini	2016-04-25	-1/+2
\| \| \| \| \| \| \|	Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default. Signed-off-by: Tom Rini <trini@konsulko.com>
*	sunxi: Enable CMD_GPIO on all sunxi boards	Hans de Goede	2016-04-12	-1/+0
\| \| \| \| \| \| \| \| \| \| \| \| \|	We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after its Kconfig conversion it has ended up missing on some recently added boards. Simply select it for ARCH_SUNXI, so that we get it on all sunxi boards for both a consistent user experience and simpler defconfig files. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
*	sunxi: Cubietruck Plus: Enable USB Kconfig options in defconfig	Chen-Yu Tsai	2016-04-01	-1/+9
\| \| \| \| \| \| \| \| \| \| \| \| \| \|	The Cubietruck Plus uses all 3 USB controllers: - USB OTG functions are provided by the musb USB OTG controller - Onboard SATA is provied by a USB-SATA bridge connected to USB1 - The USB host ports on the board are provided by an HSIC USB hub FLDO1 is set to 1.2V for HSIC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
*	sunxi: Add defconfig for Cubietruck Plus	Chen-Yu Tsai	2016-03-23	-0/+18
	Cubietruck Plus is a A83T/H8 based development board. The board has standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet, WiFi, headphone out / mic in, and various GPIO headers. The board also has an EEPROM on i2c0 which holds the MAC address. DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20 is connected to the reset control of the PHY. EMAC is not actually supported yet. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>