summaryrefslogtreecommitdiff
path: root/common/usb_hub.c
Commit message (Collapse)AuthorAgeLines
* usb: Use well-known descriptor sizes when parsing configurationJulius Werner2013-08-26-10/+4
| | | | | | | | | | | The existing USB configuration parsing code relies on the descriptors' own length values when reading through the configuration blob. Since the size of those descriptors is always well-defined, we should rather use the known sizes instead of trusting device-provided values to be correct. Also adds some safety to potential out-of-order descriptors. Change-Id: I16f69dfdd6793aa0fe930b5148d4521f3e5c3090 Signed-off-by: Julius Werner <jwerner@chromium.org>
* USB: usb-hub: Add a weak function for resetting devicesDan Murphy2013-08-26-0/+12
| | | | | | | Add a __weak function that can be overridden to reset devices attached to an ehci devices after the FEAT_POWER has been submitted Signed-off-by: Dan Murphy <dmurphy@ti.com>
* usb_hub: fix power cycling logicNikita Kiryanov2013-07-29-2/+2
| | | | | | | | | | | When power cycling the hub ports, a misbehaving port will prevent all ports from being powered on because we quit at the first sign of trouble. Skip problematic ports instead of failing the entire power on. Cc: Marek Vasut <marex@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-19/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* usb: ehci: add Faraday USB 2.0 EHCI supportKuo-Jung Su2013-06-12-1/+6
| | | | | | | | | | | | | | | | | | | This patch adds support to both Faraday FUSBH200 and FOTG210, the differences between Faraday EHCI and standard EHCI are listed bellow: 1. The PORTSC starts at 0x30 instead of 0x44. 2. The CONFIGFLAG(0x40) is not only un-implemented, and also has its address space removed. 3. Faraday EHCI is a TDI design, but it doesn't compatible with the general TDI implementation found at both U-Boot and Linux. 4. The ISOC descriptors differ from standard EHCI in several ways. But since U-boot doesn't support ISOC, we don't have to worry about that. Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> CC: Marek Vasut <marex@denx.de>
* usb: hub: make minimum power-on delay configurableKuo-Jung Su2013-06-12-2/+6
| | | | | | | | | | This patch makes the minimum power-on delay for USB HUB become configurable. The original design waits at least 100 msec here, but some EHCI controlers(e.g. Faraday EHCI) are known to require much longer delay interval. Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> CC: Marek Vasut <marex@denx.de>
* usb: fix: Fixing Port status and feature number constantsVivek Gautam2013-05-06-12/+28
| | | | | | | Fix the Port status bit constants and Port feature number constants as a part of USB 2.0 and USB 3.0 Hub class. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
* usb: hub: Parallelize power-cycling of root-hub portsVivek Gautam2013-05-06-7/+12
| | | | | | | | | | | | Untill now we power-cycle (aka: disable power on a port and re-enabling again) one port at a time. Delay of 20ms for Port-power to change multiplies with number of ports in this case. So better we parallelize this process: disable power on all ports, wait for port-power to stabilize and then re-enable the power subsequently. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
* USB: SS: Add support for Super Speed USB interfaceVivek Gautam2013-05-05-2/+6
| | | | | | | | This adds usb framework support for super-speed usb, which will further facilitate to add stack support for xHCI. Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com> Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
* usb: hub: Fix enumration timeoutVivek Gautam2013-05-05-1/+0
| | | | | | | | | | | | | | Patch b6d7852c increases timeout for enumeration, taking worst case to be 10 sec. get_timer() api returns timestamp in milliseconds, which is what we are checking in the do-while() loop in usb_hub_configure() (get_timer(start) < CONFIG_SYS_HZ * 10). This should give us a required check for 10 seconds, and thereby we don't need to add additional mdelay of 100 microseconds in each cycle. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
* usb: hub: Power-cycle on root-hub portsVivek Gautam2013-05-05-0/+34
| | | | | | | | | XHCI ports are powered on after a H/W reset, however EHCI ports are not. So disabling and re-enabling power on all ports invariably. Signed-off-by: Amar <amarendra.xt@samsung.com> Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
* usb: common: Weed out USB_**_PRINTFs from usb frameworkVivek Gautam2013-05-05-88/+74
| | | | | | | | USB_PRINTF, USB_HUB_PRINTF, USB_STOR_PRINTF, USB_KBD_PRINTF are nothing but conditional debug prints, depending on DEBUG. So better remove them and use debug() simply. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
* usb: Clean up newly allocated device nodes in case of configuration failureMilind Choudhary2012-12-17-0/+2
| | | | | | | | If probe of a newly connected device fails for some reason, clean up the allocated entry in usb_dev array. Signed-off-by: Milind Choudhary <milindc@codeaurora.org> Signed-off-by: Simon Glass <sjg@chromium.org>
* usbh/ehci: Increase timeout for enumerationVipin Kumar2012-12-17-5/+28
| | | | | | | | | | | | | | | | | | | | | | | | | The current logic reads the port status just once after usb_hub_power_on and expects the portstatus and portchange to report the connection status immediately and correctly. Few pen drives are not able to report both of them immediately ie. those pens report the connection change but not the connected state after the first read. This opportunity once lost is gone for ever because the u-boot, unlike linux or any other OS, works in polling mode. This patch modifies the logic to read the port status continuously until the portstatus and portchange both report a connection change as well as a connected state or no connection change and no connection. This logic is placed in a timeout of 10 sec. At the end of it, the pen drive would have either reported a ONE or a ZERO in bit 1 of portstatus as well as portchange. It enhances the set of pen drives which can eventually be detected by u-boot Note: This 10 second timeout is based purely on several experiments done with the broken pen drives Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* usb: lowlevel interface change to support multiple controllersLucas Stach2012-10-15-1/+1
| | | | | | | | | | | Carry an index in the lowlevel usb functions to make specify the respective usb controller. Also pass through an controller struct from lowlevel_init to the creation of the root usb device of this controller. Signed-off-by: Lucas Stach <dev@lynxeye.de> Reviewed-by: Marek Vasut <marex@denx.de>
* usb: do explicit unaligned accessesLucas Stach2012-09-21-5/+9
| | | | | | | | | | | | | | | usb_hub_descriptor has to be packed as it's used for communication with the device. Member wHubCharacteristics violates the natural alignment rules. Use explicit unaligned access functions for this member. Fixes ARMv7 traping while using USB. v2: fix typo found by Thomas Langer v3: rebased on top of u-boot-usb/master Signed-off-by: Lucas Stach <dev@lynxeye.de>
* USB: Align buffers at cachelinePuneet Saxena2012-05-20-13/+14
| | | | | | | | | | | | This avoids cache-alignment warnings shown in console when a usb command is entered. Whenever X bytes of unaligned buffer is invalidated, arm core invalidates X + Y bytes as per the cache line size and throws these warnings. Signed-off-by: Puneet Saxena <puneets@nvidia.com> Signed-off-by: Marek Vasut <marex@denx.de>
* usb: replace wait_ms() with mdelay()Mike Frysinger2012-03-19-5/+5
| | | | | | | | | | | | | | | | | | | | | | | Common code has a mdelay() func, so use that instead of the usb-specific wait_ms() func. This also fixes the build errors: ohci-hcd.c: In function 'submit_common_msg': /usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available ohci-hcd.c:1519:9: sorry, unimplemented: called from here /usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available ohci-hcd.c:1816:10: sorry, unimplemented: called from here /usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available ohci-hcd.c:1827:10: sorry, unimplemented: called from here /usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available ohci-hcd.c:1844:10: sorry, unimplemented: called from here /usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available ohci-hcd.c:1563:11: sorry, unimplemented: called from here /usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available ohci-hcd.c:1583:9: sorry, unimplemented: called from here make[1]: *** [ohci-hcd.o] Error 1 Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Marek Vasut <marex@denx.de>
* USB: relax usbcore reset timingsWolfgang Grandegger2012-03-03-1/+4
| | | | | | | | | | | | Following the corresponding Linux code, this patch relaxes reset timings waiting at least 100ms after power to the ports. There are some reports that it helps make enumeration work better on some high speed devices. Furthermore, the wait is only done once after power has been enabled on all ports. CC: Remy Bohmer <linux@bohmer.net> CC: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: Wolfgang Grandegger <wg@denx.de>
* USB: Separate out USB hub driverMarek Vasut2012-03-03-0/+476
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Remy Bohmer <linux@bohmer.net> Acked-by: Mike Frysinger <vapier@gentoo.org>