| Commit message (Collapse) | Author | Age | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
add subpagesize, nand options and bbt options to the
"nand info" output.
=> nand info
Device 0: nand0, sector size 256 KiB
Page size 4096 b
OOB size 256 b
Erase size 262144 b
subpagesize 4096 b
options 0x 200
bbt options 0x 8000
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This command is only enabled by one board, complicates the NAND code,
and doesn't appear to have been functioning properly for several
years. If there are no bad blocks in the NAND region being written
nand_write_skip_bad() will take the shortcut of calling nand_write()
which bypasses the special yaffs handling. This causes invalid YAFFS
data to be written. See
http://lists.denx.de/pipermail/u-boot/2011-September/102830.html for
an example and a potential workaround.
U-Boot still retains the ability to mount and access YAFFS partitions
via CONFIG_YAFFS2.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Previously NAND writes were only verified when CONFIG_MTD_NAND_VERIFY_WRITE
was defined. On boards without this define writes could fail silently.
Boards with CONFIG_MTD_NAND_VERIFY_WRITE could prematurely report
failures which ECC could correct.
Add a verification step after all "nand write[.x]" commands to ensure the
writes were successful. The verification uses ECC for for "normal"
writes, but does not for raw and yaffs writes. Some test cases which
inject fake bad bits on a 2K page flash are below.
Test cases with CONFIG_MTD_NAND_VERIFY_WRITE defined:
Example of an ECC write which previously failed when
CONFIG_MTD_NAND_VERIFY_WRITE was defined, but now succeeds because ECC
is used during verification:
nand erase 0 0x10000
dhcp /somefile
mw.b 0x10000 0xff 0x2000
mw.b 0x10020 0xfe 1
nand write.raw 0x10000 0x800 1
mw.b 0x1000020 0x01 1
nand write 0x1000000 0x800 0x1800
Test cases without CONFIG_MTD_NAND_VERIFY_WRITE defined:
Example of an ECC write which previously silently failed:
nand erase 0 0x10000
dhcp /somefile
mw.b 0x10000 0xff 0x2000
mw.b 0x10020 0x00 1
nand write.raw 0x10000 0x800 1
mw.b 0x1000020 0xff 1
nand write 0x1000000 0x800 0x1800
Example of a raw write which previously failed silently due to stuck
data bit, but now errors out:
nand erase 0 0x10000
dhcp /somefile
mw.b 0x10000 0xff 0x2000
mw.b 0x10020 0xfe 1
nand write.raw 0x10000 0x800 1
mw.b 0x1000020 0x01 1
nand write.raw 0x1000000 0x800 3
Example of a raw write which previously failed silently due to stuck OOB
bit, but now errors out:
nand erase 0 0x10000
dhcp /somefile
mw.b 0x10000 0xff 0x2000
mw.b 0x10810 0xfe 1
nand write.raw 0x10000 0x800 1
mw.b 0x1000810 0x01 1
nand write.raw 0x1000000 0x800 3
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
|
|
|
|
|
|
|
|
| |
The arg_off() and arg_off_size() update the 'current NAND
device' variable (dev). This is then used when assigning the
(nand_info_t*)nand value. Place the assignment after the
arg_off(_size) calls to prevent using incorrect (nand_info_t*)
nand value.
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
make the use of legacy image format configurable through
the config define CONFIG_IMAGE_FORMAT_LEGACY.
When relying on signed FIT images with required signature check
the legacy image format should be disabled. Therefore introduce
this new define and enable legacy image format if CONFIG_FIT_SIGNATURE
is not set. If CONFIG_FIT_SIGNATURE is set disable per default
the legacy image format.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Lars Steubesand <lars.steubesand@philips.com>
Cc: Mike Pearce <mike@kaew.be>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
|
|
| |
User's confirmation is asked in different commands. This commit adds a
function for such confirmation.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
|
|
|
|
|
|
|
|
|
|
| |
When executing nand scrub, the user gets the prompt:
Really scrub this NAND flash? <y/N>
We do not want the annoying usage displayed when saying N here.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
|
|
|
|
|
|
|
|
| |
If a non-zero value is given to only_oob argument,
printing the main area is skipped.
With a little modification, we can skip the whole
while loop.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
|
|
|
|
|
|
|
| |
If datbuf = memalign(ARCH_DMA_MINALIGN, nand->writesize);
succeeds and
oobbuf = memalign(ARCH_DMA_MINALIGN, nand->oobsize);
fails, nand_dump function should free databuf.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
adjust_size_for_badblocks reduces the operation size to account
for the block skipping done by the read/write functions when an
interval (partition name or whole chip) is specified rather than a data
amount.
Erase does not do block skipping, except for erase.spread which takes
a data amount rather than an interval (and thus already does not call
adjust_size_for_badblocks). Calling adjust_size_for_badblocks when
block skipping is not done means that if bad blocks are present,
the "nand erase.part" and "nand erase.chip" commands will fail to erase
blocks at the end of the interval.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Harvey Chapman <hchapman@3gfp.com>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch is essentially an update of u-boot MTD subsystem to
the state of Linux-3.7.1 with exclusion of some bits:
- the update is concentrated on NAND, no onenand or CFI/NOR/SPI
flashes interfaces are updated EXCEPT for API changes.
- new large NAND chips support is there, though some updates
have got in Linux-3.8.-rc1, (which will follow on top of this patch).
To produce this update I used tag v3.7.1 of linux-stable repository.
The update was made using application of relevant patches,
with changes relevant to U-Boot-only stuff sticked together
to keep bisectability. Then all changes were grouped together
to this patch.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
[scottwood@freescale.com: some eccstrength and build fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
| |
Adjust the sizes calculated for whole partition/chip operations by
removing the size of bad blocks so we don't try to erase/read/write
past a partition/chip boundary.
Signed-off-by: Harvey Chapman <hchapman@3gfp.com>
|
|
|
|
|
|
|
| |
The flag changed from WITH_INLINE_OOB to WITH_YAFFS_OOB by accident in
418396e.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We make these two functions take a size_t pointer to how much space
was used on NAND to read or write the buffer (when reads/writes happen)
so that bad blocks can be accounted for. We also make them take an
loff_t limit on how much data can be read or written. This means that
we can now catch the case of when writing to a partition would exceed
the partition size due to bad blocks. To do this we also need to make
check_skip_len count not just complete blocks used but partial ones as
well. All callers of nand_(read|write)_skip_bad are adjusted to call
these with the most sensible limits available.
The changes were started by Pantelis and finished by Tom.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
|
|
|
|
| |
Use setenv_ulong(), setenv_hex() and setenv_addr() in common/
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
|
| |
"nand read.part addr off size" would be treated as "nand read.raw addr off 1"
It now fails as intended stating "Unknown nand command suffix '.part'"
Signed-off-by: Harvey Chapman <hchapman@3gfp.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds a NAND Flash torture feature, which is useful as a block stress
test to determine if a block is still good and reliable (or should be marked as
bad), e.g. after a write error.
This code is ported from mtd-utils' lib/libmtd.c.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: removed unnec. ifdef and unwrapped error strings]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
cmd_boot.c:40:5: warning: symbol 'do_go' was not declared. Should it be static?
cmd_bootm.c:164:6: warning: symbol '__arch_preboot_os' was not declared. Should it be static?
cmd_bootm.c:477:5: warning: symbol 'do_bootm_subcommand' was not declared. Should it be static?
cmd_bootm.c:1022:1: error: directive in argument list
cmd_bootm.c:1028:1: error: directive in argument list
cmd_bootm.c:1029:1: error: directive in argument list
cmd_bootm.c:1036:1: error: directive in argument list
cmd_bootm.c:1042:1: error: directive in argument list
cmd_bootm.c:1044:1: error: directive in argument list
cmd_bootm.c:1045:1: error: directive in argument list
cmd_bootm.c:1047:1: error: directive in argument list
cmd_bootm.c:1089:5: warning: symbol 'do_iminfo' was not declared. Should it be static?
cmd_bootm.c:1176:5: warning: symbol 'do_imls' was not declared. Should it be static?
cmd_bootm.c:1654:1: error: directive in argument list
cmd_bootm.c:1660:1: error: directive in argument list
cmd_console.c:32:5: warning: symbol 'do_coninfo' was not declared. Should it be s
cmd_date.c:46:5: warning: symbol 'do_date' was not declared. Should it be static?
cmd_echo.c:27:5: warning: symbol 'do_echo' was not declared. Should it be static?
cmd_exit.c:27:5: warning: symbol 'do_exit' was not declared. Should it be static?
cmd_fat.c:97:5: warning: symbol 'do_fat_ls' was not declared. Should it be static?
cmd_fat.c:136:5: warning: symbol 'do_fat_fsinfo' was not declared. Should it be s
cmd_fdt.c:66:5: warning: symbol 'do_fdt' was not declared. Should it be static?
cmd_fdt.c:542:43: warning: incorrect type in assignment (different base types)
cmd_fdt.c:542:43: expected unsigned int [unsigned] [usertype] <noident>
cmd_fdt.c:542:43: got restricted __be32 [usertype] <noident>
cmd_fdt.c:679:42: warning: cast to restricted __be32
cmd_fdt.c:820:1: error: directive in argument list
cmd_fdt.c:822:1: error: directive in argument list
cmd_flash.c:292:5: warning: symbol 'do_flinfo' was not declared. Should it be static?
cmd_flash.c:324:5: warning: symbol 'do_flerase' was not declared. Should it be static?
cmd_flash.c:457:5: warning: symbol 'do_protect' was not declared. Should it be st
cmd_help.c:27:5: warning: symbol 'do_help' was not declared. Should it be static?
cmd_i2c.c:136:6: warning: symbol '__def_i2c_init_board' was not declared. Should it be static?
cmd_i2c.c:144:14: warning: symbol '__def_i2c_get_bus_speed' was not declared. Should it be static?
cmd_i2c.c:151:5: warning: symbol '__def_i2c_set_bus_speed' was not declared. Should it be static?
cmd_i2c.c:1322:1: error: directive in argument list
cmd_i2c.c:1324:1: error: directive in argument list
cmd_i2c.c:1326:1: error: directive in argument list
cmd_i2c.c:1328:1: error: directive in argument list
cmd_i2c.c:1337:1: error: directive in argument list
cmd_i2c.c:1339:1: error: directive in argument list
cmd_irq.c:27:5: warning: symbol 'do_interrupts' was not declared. Should it be static?
cmd_itest.c:133:5: warning: symbol 'binary_test' was not declared. Should it be static?
cmd_itest.c:158:5: warning: symbol 'do_itest' was not declared. Should it be stat
cmd_load.c:54:5: warning: symbol 'do_load_serial' was not declared. Should it be static?
cmd_load.c:431:6: warning: symbol 'his_eol' was not declared. Should it be static?
cmd_load.c:432:6: warning: symbol 'his_pad_count' was not declared. Should it be static?
cmd_load.c:433:6: warning: symbol 'his_pad_char' was not declared. Should it be static?
cmd_load.c:434:6: warning: symbol 'his_quote' was not declared. Should it be static?
cmd_load.c:436:5: warning: symbol 'do_load_serial_bin' was not declared. Should it be static?
cmd_load.c:549:6: warning: symbol 'send_pad' was not declared. Should it be static?
cmd_load.c:558:6: warning: symbol 'ktrans' was not declared. Should it be static?
cmd_load.c:568:5: warning: symbol 'chk1' was not declared. Should it be static?
cmd_load.c:578:6: warning: symbol 's1_sendpacket' was not declared. Should it be static?
cmd_load.c:587:6: warning: symbol 'send_ack' was not declared. Should it be static?
cmd_load.c:600:6: warning: symbol 'send_nack' was not declared. Should it be static?
cmd_load.c:614:6: warning: symbol 'os_data_init' was not declared. Should it be static?
cmd_load.c:615:6: warning: symbol 'os_data_char' was not declared. Should it be static?
cmd_load.c:657:6: warning: symbol 'k_data_init' was not declared. Should it be static?
cmd_load.c:663:6: warning: symbol 'k_data_save' was not declared. Should it be static?
cmd_load.c:669:6: warning: symbol 'k_data_restore' was not declared. Should it be static?
cmd_load.c:675:6: warning: symbol 'k_data_char' was not declared. Should it be static?
cmd_load.c:693:6: warning: symbol 'send_parms' was not declared. Should it be static?
cmd_load.c:694:6: warning: symbol 'send_ptr' was not declared. Should it be static?
cmd_load.c:698:6: warning: symbol 'handle_send_packet' was not declared. Should i
cmd_mdio.c:60:5: warning: symbol 'mdio_write_ranges' was not declared. Should it be static?
cmd_mdio.c:82:5: warning: symbol 'mdio_read_ranges' was not declared. Should it be static?
cmd_mdio.c:115:5: warning: symbol 'extract_reg_range' was not declared. Should it be static?
cmd_mdio.c:144:5: warning: symbol 'extract_phy_range' was not declared. Should it
cmd_mem.c:54:5: warning: symbol 'do_mem_md' was not declared. Should it be static?
cmd_mem.c:150:5: warning: symbol 'do_mem_mm' was not declared. Should it be static?
cmd_mem.c:154:5: warning: symbol 'do_mem_nm' was not declared. Should it be static?
cmd_mem.c:159:5: warning: symbol 'do_mem_mw' was not declared. Should it be static?
cmd_mem.c:256:5: warning: symbol 'do_mem_cmp' was not declared. Should it be static?
cmd_mem.c:326:5: warning: symbol 'do_mem_cp' was not declared. Should it be static?
cmd_mem.c:436:5: warning: symbol 'do_mem_base' was not declared. Should it be static?
cmd_mem.c:449:5: warning: symbol 'do_mem_loop' was not declared. Should it be static?
cmd_mem.c:595:5: warning: symbol 'do_mem_mtest' was not declared. Should it be static?
cmd_mem.c:618:26: warning: Using plain integer as NULL pointer
cmd_mem.c:1057:5: warning: symbol 'do_mem_crc' was not declared. Should it be static?
cmd_misc.c:30:5: warning: symbol 'do_sleep' was not declared. Should it be static
cmd_mmc.c:118:5: warning: symbol 'do_mmcinfo' was not declared. Should it be static?
cmd_mmc.c:272:32: warning: Using plain integer as NULL pointer
cmd_mmc.c:150:5: warning: symbol 'do_mmcops' was not declared. Should it be stati
cmd_mp.c:27:1: warning: symbol 'cpu_cmd' was not declared. Should it be static?
cmd_mp.c:85:1: error: directive in argument list
cmd_mp.c:88:1: error: directive in argument list
cmd_mtdparts.c:150:18: warning: symbol 'mtdids' was not declared. Should it be static?
cmd_mtdparts.c:153:18: warning: symbol 'devices' was not declared. Should it be static?
cmd_mtdparts.c:713:5: warning: symbol 'mtd_device_validate' was not declared. Should it be static?
cmd_mtdparts.c:1887:5: warning: symbol 'do_chpart' was not declared. Should it be static?
cmd_mtdparts.c:1925:5: warning: symbol 'do_mtdparts' was not declared. Should it be static?
cmd_mtdparts.c:2060:1: error: directive in argument list
cmd_mtdparts.c:2063:1: error: directive in argument list
cmd_mtdparts.c:2066:1: error: directive in argument list
cmd_mtdparts.c:2071:1: error: directive in argument list
cmd_mtdparts.c:2073:1: error: directive in argument list
cmd_nand.c:377:18: error: bad constant expression
cmd_nand.c:431:5: warning: symbol 'do_nand' was not declared. Should it be static?
cmd_nand.c:796:1: error: directive in argument list
cmd_nand.c:801:1: error: directive in argument list
cmd_nand.c:802:1: error: directive in argument list
cmd_nand.c:806:1: error: directive in argument list
cmd_nand.c:819:1: error: directive in argument list
cmd_nand.c:824:1: error: directive in argument list
cmd_nand.c:825:1: error: directive in argument list
cmd_nand.c:831:1: error: directive in argument list
cmd_nand.c:918:5: warning: symbol 'do_nandboot' was not declared. Should it be static?
cmd_net.c:33:5: warning: symbol 'do_bootp' was not declared. Should it be static?
cmd_net.c:107:5: warning: symbol 'do_dhcp' was not declared. Should it be static?
cmd_net.c:120:5: warning: symbol 'do_nfs' was not declared. Should it be static?
cmd_nvedit.c:138:5: warning: symbol 'do_env_print' was not declared. Should it be static?
cmd_nvedit.c:323:5: warning: symbol '_do_env_set' was not declared. Should it be static?
cmd_nvedit.c:435:5: warning: symbol 'do_env_set' was not declared. Should it be static?
cmd_nvedit.c:514:5: warning: symbol 'do_env_edit' was not declared. Should it be static?
cmd_nvedit.c:620:5: warning: symbol 'do_env_save' was not declared. Should it be static?
cmd_nvedit.c:1016:1: error: directive in argument list
cmd_nvedit.c:1018:1: error: directive in argument list
cmd_nvedit.c:1021:1: error: directive in argument list
cmd_nvedit.c:1023:1: error: directive in argument list
cmd_nvedit.c:1024:1: error: directive in argument list
cmd_nvedit.c:1026:1: error: directive in argument list
cmd_nvedit.c:1027:1: error: directive in argument list
cmd_nvedit.c:1029:1: error: directive in argument list
cmd_nvedit.c:1030:1: error: directive in argument list
cmd_nvedit.c:1032:1: error: directive in argument list
cmd_nvedit.c:1034:1: error: directive in argument list
cmd_nvedit.c:1036:1: error: directive in argument list
cmd_nvedit.c:1037:1: error: directive in argument list
cmd_nvedit.c:1039:1: error: directive in argument list
cmd_pci.c:38:17: warning: symbol 'ShortPCIListing' was not declared. Should it be static?
cmd_pci.c:38:22: warning: 'ShortPCIListing' defined but not used [-Wunused-variable]
cmd_pci.c:411:5: warning: symbol 'do_pci' was not declared. Should it be static?
cmd_pci.c:494:1: error: directive in argument list
cmd_pci.c:497:1: error: directive in argument list
cmd_reginfo.c:40:5: warning: symbol 'do_reginfo' was not declared. Should it be static?
cmd_sata.c:31:5: warning: symbol 'sata_curr_device' was not declared. Should it be static?
note -> ata_piix.c doesn't seem to use 'sata_curr_device'; deleted.
cmd_sata.c:32:18: warning: symbol 'sata_dev_desc' was not declared. Should it be static?
cmd_sata.c:70:5: warning: symbol 'do_sata' was not declared. Should it be static?
cmd_setexpr.c:53:5: warning: symbol 'do_setexpr' was not declared. Should it be static?
cmd_source.c:186:1: error: directive in argument list
cmd_source.c:190:1: error: directive in argument list
cmd_test.c:27:5: warning: symbol 'do_test' was not declared. Should it be static?
cmd_test.c:153:5: warning: symbol 'do_false' was not declared. Should it be static?
cmd_test.c:164:5: warning: symbol 'do_true' was not declared. Should it be static
cmd_usb.c:43:6: warning: symbol 'usb_get_class_desc' was not declared. Should it be static?
cmd_usb.c:69:6: warning: symbol 'usb_display_class_sub' was not declared. Should it be static?
cmd_usb.c:151:6: warning: symbol 'usb_display_string' was not declared. Should it be static?
cmd_usb.c:161:6: warning: symbol 'usb_display_desc' was not declared. Should it be static?
cmd_usb.c:195:6: warning: symbol 'usb_display_conf_desc' was not declared. Should it be static?
cmd_usb.c:210:6: warning: symbol 'usb_display_if_desc' was not declared. Should it be static?
cmd_usb.c:227:6: warning: symbol 'usb_display_ep_desc' was not declared. Should it be static?
cmd_usb.c:252:6: warning: symbol 'usb_display_config' was not declared. Should it be static?
cmd_usb.c:283:6: warning: symbol 'usb_show_tree_graph' was not declared. Should it be static?
cmd_usb.c:343:6: warning: symbol 'usb_show_tree' was not declared. Should it be static?
cmd_usb.c:356:5: warning: symbol 'do_usbboot' was not declared. Should it be static?
cmd_usb.c:366:5: warning: symbol 'do_usb' was not declared. Should it be static?
cmd_version.c:31:5: warning: symbol 'do_version' was not declared. Should it be s
cmd_ximg.c:46:1: warning: symbol 'do_imgextract' was not declared. Should it be static?
cmd_ximg.c:272:1: error: directive in argument list
cmd_ximg.c:276:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In order for cache invalidation and flushing to work properly, the data
and OOB buffers must be aligned to full cache lines.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Micron NAND flash (e.g. MT29F4G08ABADAH4) BLOCK LOCK READ STATUS is not
the same as others. Instead of bit 1 being lock, it is #lock_tight.
To make the driver support either format, ignore bit 1 and use only
bit 0 and bit 2.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|/
|
|
|
|
|
|
|
| |
NAND unlock command allows an invert bit to be set to unlock all but
the selected page range.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[scottwood@freescale.com: updated docs and added comment about invert bit]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit 418396e212b59bf907dbccad997ff50f7eb61b16 introduced a
bug that causes nand read and nand write to crash in strcmp
due to a null pointer.
Root cause is that strchr(cmd, '.') returns a null pointer when
the input string does not contain a '.'
The strcmp function does not check for null pointers, resulting
in a crash.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Scott Wood <scott@tyr.buserror.net>
|
|
|
|
|
|
|
|
|
| |
cmd_nand.c: In function 'raw_access':
cmd_nand.c:397:9: warning: variable 'rwsize' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
|
| |
A use for this is to read, modify, erase, and write an entire block as a
single unit, as a replacement for the biterr command. This way gives
more flexibility in that you can also test multiple bit errors, errors
in the ECC, etc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
|
| |
cmd_nand.c: In function ‘arg_off_size’:
cmd_nand.c:216:5: warning: ‘maxsize’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
|
|
|
|
|
|
|
| |
These calls should not be made directly any more, since bootstage
will call the show_boot_...() functions as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
|
| |
This changes over the NAND progress numbers to use enums from
bootstage.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
|
|
| |
Rather than the caller negating our progress numbers to indicate an
error has occurred, which seems hacky, add a function to indicate this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
|
|
|
|
|
|
|
| |
Change all files in common/ to use CMD_RET_USAGE instead of calling
cmd_usage() directly. I'm not completely sure about this patch since
the code since impact is small (100 byte or so on ARM) and it might
need splitting into smaller patches. But for now here it is.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
With 2a8e0fc nand_do_read_ops changed in behavior slightly (keeping in sync
with the kernel which did this change in b64d39d8) such that the OOB data is
always copied into oobbuf and never appended to datbuf. Within U-Boot only
the nand_dump function (for the dump nand subcommand) was expecting the OOB
data to only be appended to datbuf. So we now change nand_dump to not
malloc extra space, correct the comment about datbuf and OOB data and switch
the pointer to oobbuf before printing.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The "nand info" and "nand device" now set shell/environment variables:
nand_writesize ... nand page size
nand_oobsize ..... nand oob area size
nand_erasesize ... nand erase block size
Also, the "nand info" command now displays this info.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: removed unnecessary memsets]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This allows the scrub command to scrub without asking the user if he really
wants to scrub the area. Useful in scripts.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
These commands should work around various "hardware" ECC and BCH methods.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: s/write the page/access the page/]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
cmd_nand.c: In function ‘do_nand’:
cmd_nand.c:490:7: warning: variable ‘chip’ set but not used
[-Wunused-but-set-variable]
cmd_nand.c:489:7: warning: variable ‘part’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
|
|
|
|
|
|
|
|
|
| |
Rather than having a bunch of random commands handle autostart behavior,
unify the logic in a single place. This also fixes building of these
different commands when bootm is disabled.
Acked-by: Matthew McClintock <msm@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add another nand write. variant, trimffs. This command will request of
nand_write_skip_bad() that all trailing all-0xff pages will be
dropped from eraseblocks when they are written to flash as-per the
reccommended behaviour of the UBI FAQ [1].
The function that implements this timming is the drop_ffs() function
by Artem Bityutskiy, ported from the mtd-utils tree.
[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_flasher_algo
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Artem Bityutskiy <dedekind1@gmail.com>
CC: Detlev Zundel <dzu@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In a future commit the behaviour of nand_write_skip_bad()
will be further extended.
Convert the only flag currently passed to the nand_write_
skip_bad() function to a bitfield of only one allocated
member. This should avoid an explosion of int's at the
end of the parameter list or the ambiguous calls like
nand_write_skip_bad(info, offset, len, buf, 0, 1, 1);
nand_write_skip_bad(info, offset, len, buf, 0, 1, 0);
Instead there will be:
nand_write_skip_bad(info, offset, len, buf, WITH_YAFFS_OOB |
WITH_OTHER);
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
|
| |
Since commit 30486322 (nand erase: .spread, .part, .chip subcommands)
the arguments off and size are no longer optional.
Signed-off-by: Daniel Hobi <daniel.hobi@schmid-telecom.ch>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
| |
This patch add addition suffix to nand write to give the uboot
the power to directly burn the yaffs image to nand.
Signed-off-by: Lei Wen <leiwen@marvell.com>
|
|
|
|
|
|
|
|
|
|
| |
This reverts commit 5a442c0addc69d0c4b58e98e5aec1cf07576debb.
This commit changed the behaviour of getenv_yesno() (both the default
behaviour and the documented behaviour for abbreviated arguments)
which resulted in problems in several areas.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
|
|
|
| |
Use the new helper func to clean up duplicate logic handling of the
autostart env var.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
|
|
|
|
|
|
| |
The duplication of the do_bootm prototype has gotten out of hand,
and they're pretty much all outdated (wrt constness). Unify them
all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
|
|
|
|
|
|
|
| |
Commit ea533c260a801c4e51f92f75165cebe6d7b01e35 changed
arg_off_size to take a pointer to a device index, rather than
to the device itself. When updating callers, the nand unlock
code was missed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
|
| |
The dump command is made to increment its address on repeat,
as md does. Other commands do not make sense to issue repeatedly,
and can be irritating when it happens accidentally, so don't.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
A while back, in http://lists.denx.de/pipermail/u-boot/2009-June/054428.html,
Michele De Candia posted a patch to not count bad blocks toward the
requested size to be erased. This is desireable when you're passing in
something like $filesize, but not when you're trying to erase a partition.
Thus, a .spread subcommand (named for consistency with
http://lists.denx.de/pipermail/u-boot/2010-August/075163.html) is introduced
to make explicit the user's desire to erase for a given amount of data,
rather than to erase a specific region of the chip.
While passing $filesize to "nand erase" is useful, accidentally passing
something like $fliesize currently produces quite unpleasant results, as the
variable evaluates to nothing and U-Boot assumes that you want to erase
the entire rest of the chip/partition. To improve the safety of the
erase command, require the user to make explicit their intentions by
using a .part or .chip subcommand. This is an incompatible user interface
change, but keeping compatibility would eliminate the safety gain, and IMHO
it's worth it.
While touching nand_erase_opts(), make it accept 64-bit offsets and sizes,
fix the percentage display when erase length is rounded up, eliminate
an inconsistent warning about rounding up the erase length which only
happened when the length was less than one block (rounding up for $filesize
is normal operation), and add a diagnostic if there's an attempt to erase
beginning at a non-block boundary.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- If the current device is overridden by a named partition,
- update the caller's pointer/index, rather than copy over the
nand_info struct, and
- be sure to call board_nand_select_device even when the device
is overridden by a named partition.
- Support 64-bit offsets/sizes in a few more places.
- Refactor arg_off_size for added readability and flexibility,
and some added checks such as partition size.
- Remove redundant check for bad subcommands -- if there's no match
it'll print usage when it gets to the end anyway.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
|
|
|
|
|
|
|
|
|
|
| |
Most of the files have U_BOOT_CMD on a separate line,
but a few didn't and had the first line on the same line
as U_BOOT_CMD.
This changes these files by adding a line break and a tab
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Change if (ok) {
bunch of stuff
} else {
error
}
to
if (error) {
get out
}
proceed with bunch of stuff
Plus a few whitespace cleanups.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|