summaryrefslogtreecommitdiff
path: root/boards.cfg
Commit message (Collapse)AuthorAgeLines
...
* | Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-12-10-4/+10
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/armv7/rmobile/Makefile doc/README.scrapyard Needed manual fix: arch/arm/cpu/armv7/omap-common/Makefile board/compulab/cm_t335/u-boot.lds
| * | t2080qds/ramboot: enable PBL tool for t2080qdsShengzhou Liu2013-11-25-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | Add the default RCW(SerDes 0x66_0x16) and PBI configure file for T2080QDS board, so we can use PBL tool to generate the ramboot image to support boot from NAND/SPI/SD. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
| * | powerpc/t2080qds: add support for t2080qds boardShengzhou Liu2013-11-25-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The T2080QDS is a high-performance computing evaluation, development and test platform supporting the T2080 QorIQ Power Architecture processor. T2080QDS feature overview Processor: - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz Memory: - Single memory controller capable of supporting DDR3 and DDR3-LV devices - Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support Ethernet interfaces: - Two 1Gbps RGMII on-board ports - Four 10Gbps XFI on-board cages - 1Gbps/2.5Gbps SGMII Riser card - 10Gbps XAUI Riser card Accelerator: - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC SerDes: - 16 lanes up to 10.3125GHz - Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI IFC: - 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA eSPI: - Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040) USB: - Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB) PCIE: - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) SATA: - Two SATA 2.0 ports on-board SRIO: - Two Serial RapidIO 2.0 ports up to 5 GHz eSDHC: - Supports SD/SDHC/SDXC/eMMC Card I2C: - Four I2C controllers. UART: - Dual 4-pins UART serial ports System Logic: - QIXIS-II FPGA system controll Debug Features: - Support Legacy, COP/JTAG, Aurora, Event and EVT Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: removed Makefile blank line at EOF, fix conflicts with moving DDR driver] Acked-by: York Sun <yorksun@freescale.com>
| * | powerpc/t1040qds: Correct Maintainer name in boards.cfgPriyanka Jain2013-11-25-1/+1
| | | | | | | | | | | | | | | | | | Update T1040QDS naem to Poonam Aggrwal. Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
| * | powerpc/t104xrdb: Add T1042RDB_PI board supportPriyanka Jain2013-11-13-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1042RDB_PI is Freescale Reference Design Board supporting the T1042 QorIQ Power Architecture™ processor. T1042 is a reduced personality of T1040 SoC without Integrated 8-port Gigabit. The board is designed with low power features targeted for Printing Image Market. T1042RDB_PI is similar to T1040RDB board with few differences like it has video interface, supports T1042 personality T1042RDB_PI board Overview ----------------------- - Four e5500 cores, each with a private 256 KB L2 cache - 256 KB shared L3 CoreNet platform cache (CPC) - Interconnect CoreNet platform - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - Packet parsing, classification, and distribution - Queue management for scheduling, packet sequencing, and congestion management - Cryptography Acceleration - RegEx Pattern Matching Acceleration - IEEE Std 1588 support - Hardware buffer management for buffer allocation and deallocation - Ethernet interfaces - Two on-board RGMII 10/100/1G ethernet ports. - SERDES Connections, 8 lanes supporting: — PCI — SATA 2.0 - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and Interleaving -IFC/Local Bus - NAND flash: 1GB 8-bit NAND flash - NOR: 128MB 16-bit NOR Flash - Ethernet - Two on-board RGMII 10/100/1G ethernet ports. - PHY #0 remains powered up during deep-sleep - CPLD - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - SERDES clocks - Video - DIU supports video at up to 1280x1024x32bpp - HDMI connector - Power Supplies - USB - Supports two USB 2.0 ports with integrated PHYs - Two type A ports with 5V@1.5A per port. - SDHC - SDHC/SDXC connector - SPI - On-board 64MB SPI flash - I2C - Device connected: EEPROM, thermal monitor, VID controller, RTC - Other IO - Two Serial ports - ProfiBus port - Four I2C ports Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
| * | powerpc/t104xrdb: Add T1040RDB board supportPriyanka Jain2013-11-13-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1040RDB is Freescale Reference Design Board supporting the T1040 QorIQ Power Architecture™ processor. T1040RDB board Overview ----------------------- - Four e5500 cores, each with a private 256 KB L2 cache - 256 KB shared L3 CoreNet platform cache (CPC) - Interconnect CoreNet platform - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - Packet parsing, classification, and distribution - Queue management for scheduling, packet sequencing, and congestion management - Cryptography Acceleration - RegEx Pattern Matching Acceleration - IEEE Std 1588 support - Hardware buffer management for buffer allocation and deallocation - Ethernet interfaces - Integrated 8-port Gigabit Ethernet switch - Four 1 Gbps Ethernet controllers - SERDES Connections, 8 lanes supporting: - PCI - SGMII - QSGMII - SATA 2.0 - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and Interleaving -IFC/Local Bus - NAND flash: 1GB 8-bit NAND flash - NOR: 128MB 16-bit NOR Flash - Ethernet - Two on-board RGMII 10/100/1G ethernet ports. - PHY #0 remains powered up during deep-sleep - CPLD - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - SERDES clocks - Power Supplies - USB - Supports two USB 2.0 ports with integrated PHYs - Two type A ports with 5V@1.5A per port. - SDHC - SDHC/SDXC connector - SPI - On-board 64MB SPI flash - I2C - Devices connected: EEPROM, thermal monitor, VID controller - Other IO - Two Serial ports - ProfiBus port Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> [York Sun: fixed Makefile] Acked-by: York Sun <yorksun@freescale.com>
| * | MPC824x: remove obsolete "PN62" boardWolfgang Denk2013-11-11-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MPC824x processors have long reached EOL, and the PN62 board has not seen any board-specific updates for more than a decade. It is now causing build issues. Instead of wasting time on things nobody is interested in any more, we rather drop this board. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Wolfgang Grandegger <wg@grandegger.com> cc: Tom Rini <trini@ti.com>
| * | Merge branch 'master' of git://git.denx.de/u-boot-mipsTom Rini2013-11-11-2/+2
| |\ \
| | * | malta: add myself to maintainersPaul Burton2013-11-09-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds me as a maintainer of the malta(el) board(s). I have access to physical Malta boards and the desire for U-boot to run well on them. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
| | * | qemu-malta: rename to just "malta"Paul Burton2013-11-09-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is in preparation for adapting this board to function correctly on a physical MIPS Malta board. The board is moved into an "imgtec" vendor directory at the same time in order to ready us for any other boards supported by Imagination in the future. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
* | | | arm: at91: support for the Calao USB-A9263 board (based on AT91SAM9263)Mateusz Kulikowski2013-12-09-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for USB-A9263 board manufactured by Calao Systems (http://www.calao-systems.com/). Code is based on old U-Boot sources (2010.09) released by Calao. Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* | | | arm, at91: add siemens corvus boardHeiko Schocher2013-12-09-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | enable support for the siemens AT91SAM9G20 based board corvus. Signed-off-by: Boris Schmidt <boris.schmidt@siemens.com> Reviewed-by: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* | | | arm, at91: add Siemens board taurus and axmHeiko Schocher2013-12-09-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | enable support for the siemens AT91SAM9G20 based boards taurus and axm. Signed-off-by: Roger Meier <r.meier@siemens.com> Reviewed-by: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* | | | Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-12-06-1/+3
|\ \ \ \
| * | | | pcm051: Support for revision 3Lars Poeschel2013-12-04-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on the board. The difference for u-boot is that is has other DDR3 RAM on it: 1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and 2. Both configurations are 512 MiB. Configure your u-boot build with pcm051_rev3 for the new RAM and pcm051_rev1 for the old RAM configuration. Board revision 2 has to use pcm051_rev1 also. Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
| * | | | cm_t335: add cm_t335 board supportIlya Ledvich2013-12-04-0/+1
| | |_|/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add cm_t335 board directory, config file. Enable build. Signed-off-by: Ilya Ledvich <ilya@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> [trini: Adapt Makefile] Signed-off-by: Tom Rini <trini@ti.com>
* | | | arm: rmobile: Add support koelsch boardNobuhiro Iwamatsu2013-12-03-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The koelsch board has R8A7791, 2GB DDR3-SDRAM, USB, Quad SPI, Ethernet, and more. This patch supports the following functions: - DDR3-SDRAM - SCIF Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Albert Aribaud <albert.u.boot@aribaud.net>
* | | | arm: rmobile: Add support lager boardNobuhiro Iwamatsu2013-12-03-0/+2
|/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The lager board has R8A7790, 4GB DDR3-SDRAM, USB, Ethernet, and more. This patch supports the following functions: - DDR3-SDRAM - SCIF Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com> Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Albert Aribaud <albert.u.boot@aribaud.net>
* | | omap730p2: Remove boardTom Rini2013-11-11-3/+0
| | | | | | | | | | | | Signed-off-by: Tom Rini <trini@ti.com>
* | | am335x_evm: Fix CONS_INDEX numberingAndrew Bradford2013-11-11-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | Commit f6d1f6e4a58edae4776937647381a43fea5e83a5 broke selection of UARTs other than UART0 for am335x_evm configurations by setting CONS_INDEX to 1 for all configurations. Revert the CONS_INDEX changes. Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
* | | boards.cfg: update email address for ti814x_evm maintainerMatt Porter2013-11-11-1/+1
|/ / | | | | | | | | | | | | Update my email address as ti814x_evm maintainer to save people some frustrating bounces and non-response. Signed-off-by: Matt Porter <matt.porter@linaro.org>
* | Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-11-09-9/+11
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
| * Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-11-07-0/+2
| |\
| | * ARM: mxs: Add PPC-AG BG0900 boardMarek Vasut2013-10-17-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | This board supports FEC Ethernet, SPI NOR and NAND flash. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Christoph Baumann <c.baumann@ppc-ag.de>
| | * udoo: Add initial support for mx6q udoo boardFabio Estevam2013-10-17-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add basic support for mx6q udoo board. For further information about Udoo board: http://www.udoo.org/ Tested booting a mainline device tree kernel and a Yocto rootfs from mmc. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | dra7xx_evm: Enabled UART-boot mode and add dra7xx_evm_uart3 buildMinal Shah2013-11-01-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UART booting is supported on this SoC, but via UART3 rather than UART1. Because of this we must change the board to use UART3 for all console access (only one UART is exposed on this board and a slight HW mod is required to switch UARTs). Signed-off-by: Minal Shah <minal.shah@ti.com> [trini: Make apply to mainline, reword commit] Signed-off-by: Tom Rini <trini@ti.com>
| * | tricorder: add configuration for a flashcard u-bootAndreas Bießmann2013-11-01-0/+1
| | | | | | | | | | | | | | | | | | | | | The 'flashcard' u-boot configuration has a readonly environment and boots a bare kernel/initrd to program the device from an clean environment. Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
| * | OMAP3: igep00x0: rename config file to omap3_igep00x0.hJavier Martinez Canillas2013-11-01-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There seems to be a naming convention for the configuration files for boards using the same SoC family. This makes easier to do changes that affect different boards based on the same SoC. Since the IGEPv2 board and the IGEP COM Module use a TI OMAP35xx/DM37xx processor, is better to rename its board config to use this naming scheme. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
| * | ARM: IGEP0033: rename config file to am335x_igep0033.hJavier Martinez Canillas2013-11-01-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There seems to be a naming convention for the configuration files for boards using the same SoC family. This makes easier to do changes that affect different boards based on the same SoC. Since the IGEP COM AQUILA use a TI AM335x processor is better to rename its board config to use this naming scheme. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
| * | arm: Remove IXP425 boards pdnb3 and scpuStefan Roese2013-10-17-2/+0
| |/ | | | | | | | | | | | | | | | | | | Remove Prodrive pdnb3 board (including the scpu variant) support from mainline. As its unmaintained and not needed any more for quite some time. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Martijn de Gouw <martijn.de.gouw@prodrive.nl> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
* | boards.cfg: remove git leftoversLuka Perkov2013-11-08-1/+0
| | | | | | | | | | | | | | Remove 'HEAD' line which is most likely left there while rebasing. It was introduced in commit 877bfe37dc00b0ae59f37742954a62bce3fdf3a0. Signed-off-by: Luka Perkov <luka@openwrt.org>
* | boards.cfg: remove trailing whitespacePaul Burton2013-11-08-1/+1
| | | | | | | | | | | | | | | | | | Commit 93e14596 "Coding Style cleanup: replace leading SPACEs by TABs" added trailing whitespace to a single line of boards.cfg. I presume this was unintentional, and it causes the file to change after running it through the reformat.py script. Remove the offending character. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
* | mpc85xx: introduce the kmp204x reference design supportValentin Longchamp2013-10-24-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch introduces the support for Keymile's kmp204x reference design. This design is based on Freescale's P2040/P2041 SoC. The peripherals used by this design are: - DDR3 RAM with SPD support - SPI NOR Flash as boot medium - NAND Flash - 2 PCIe busses (hosts 1 and 3) - 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5) - 3 Local Bus windows, with one dedicated to the QRIO reset/power mgmt FPGA - 2 HW I2C busses - last but not least, the mandatory serial port The board/keymile/kmp204x code is mostly based on Freescale's P2041rdb support and was changed according to our design (that means essentially removing what is not present on the designs and a few adaptations). There is currently only one prototype board that is based on this design and this patch also introduces it. The board is called kmlion1. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> kmp204x: update the ENV #define The comments had to be refined as well as the total size Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: fix ddr.c] Acked-by: York Sun <yorksun@freescale.com>
* | powerpc/p1010rdb: add p1010rdb-pb support with updating p1010rdb-paShengzhou Liu2013-10-16-14/+28
| | | | | | | | | | | | | | | | | | | | | | | | - Rename old P1010RDB board as P1010RDB-PA. - Add support for new P1010RDB-PB board. - Some optimization. For more details, see board/freescale/p1010rdb/README. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: fix conflicts in boards.cfg] Acked-by: York Sun <yorksun@freescale.com>
* | powerpc/t1040qds: Add T1040QDS boardPrabhakar Kushwaha2013-10-16-0/+1
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1040QDS is a high-performance computing evaluation, development and test platform supporting the T1040 QorIQ Power Architecture™ processor. T1040QDS board Overview ----------------------- - Four e5500 cores, each with a private 256 KB L2 cache - 256 KB shared L3 CoreNet platform cache (CPC) - Interconnect CoreNet platform - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - Packet parsing, classification, and distribution - Queue management for scheduling, packet sequencing, and congestion management - Cryptography Acceleration - RegEx Pattern Matching Acceleration - IEEE Std 1588 support - Hardware buffer management for buffer allocation and deallocation - Ethernet interfaces - Integrated 8-port Gigabit Ethernet switch - Four 1 Gbps Ethernet controllers - SERDES Connections, 8 lanes supporting: — PCI Express: supporting Gen 1 and Gen 2; — SGMII — QSGMII — SATA 2.0 — Aurora debug with dedicated connectors - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and Interleaving -IFC/Local Bus - NAND flash: 8-bit, async, up to 2GB. - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB - GASIC: Simple (minimal) target within Qixis FPGA - PromJET rapid memory download support - Ethernet - Two on-board RGMII 10/100/1G ethernet ports. - PHY #0 remains powered up during deep-sleep - QIXIS System Logic FPGA - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - SERDES clocks - Power Supplies - Video - DIU supports video at up to 1280x1024x32bpp - USB - Supports two USB 2.0 ports with integrated PHYs — Two type A ports with 5V@1.5A per port. — Second port can be converted to OTG mini-AB - SDHC - SDHC port connects directly to an adapter card slot, featuring: - Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC — Supporting eMMC memory devices - SPI - On-board support of 3 different devices and sizes - Other IO - Two Serial ports - ProfiBus port - Four I2C ports Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> [York Sun: fix conflict in boards.cfg] Acked-by-by: York Sun <yorksun@freescale.com>
* Coding Style cleanup: replace leading SPACEs by TABsWolfgang Denk2013-10-14-1/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Drop changes for PEP 4 following python tools] Signed-off-by: Tom Rini <trini@ti.com>
* Coding Style cleanup: remove trailing white spaceWolfgang Denk2013-10-14-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-10-14-0/+1
|\
| * Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD2013-10-11-0/+1
| |\
| | * samsung: trats2: add support for new board Trats2Piotr Wilczek2013-09-25-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | This patch add support for a new Samsung board Trats2. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-10-08-1/+0
|\ \ \ | |/ /
| * | omap1510inn: arm925t: remove supportAlbert ARIBAUD2013-10-07-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | omap1510inn is orphan and has been for years now. Reove it and, as it was the only arm925t target, also remove arm925t support. Update doc/README.scrapyard accordingly. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-10-02-0/+3
|\ \ \ | |/ /
| * | Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic2013-09-13-1174/+1176
| |\ \ | | |/ | | | | | | | | | | | | | | | | | | Conflicts: MAINTAINERS boards.cfg Signed-off-by: Stefano Babic <sbabic@denx.de>
| * | apf27: add support for the armadeus APF27 boardtrem2013-09-11-0/+1
| | | | | | | | | | | | | | | | | | Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr> Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org> Signed-off-by: Nicolas Colombain <nicolas.colombain@armadeus.com>
| * | ARM: mxs: Add SanDisk Sansa Fuze+ boardMarek Vasut2013-09-10-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add STMP3780-based Sansa Fuze+ board. This board is a small PMP device sporting a CPU which was later rebranded to i.MX233 . Currently supported is USB gadget mode and MMC . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
| * | ARM: mxs: Add Creative ZEN XFi3 boardMarek Vasut2013-09-10-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add STMP3780-based XFi3 board. This board is a small PMP device sporting a CPU which was later rebranded to i.MX233 . Currently supported is USB gadget mode and both external SD and internal Phison SD-NAND bridge . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
| * | ARM: mxs: Sort the mx23evk and mx23_olinuxinoMarek Vasut2013-09-10-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | These boards were not sortes in the boards.cfg, fix this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br>
* | | boards.cfg: Fix the comment for invoking tools/reformat.py from vimAxel Lin2013-09-20-1/+1
| |/ |/| | | | | | | | | | | Add the missing bang (!) to execute external command, otherwise it does not work. Signed-off-by: Axel Lin <axel.lin@ingics.com>
* | Merge and reformat boards.cfg and MAINTAINERSAlbert ARIBAUD2013-09-12-1172/+1173
| | | | | | | | | | | | | | | | Put all informations about targets, including state (active or orphan) and maintainers, in boards.cfg; remove MAINTAINERS; adjust the build system accordingly. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
generated by cgit v1.1 at 2024-11-06 20:20:43 +0000