| Commit message (Collapse) | Author | Age | Lines |
|
|
|
|
|
| |
Cover all of the boston and malta variations.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2,
and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x-evm. With
the default values LCDC suffers from DMA FIFO underflows and frame
synchronization lost errors. The initialization values are the highest
that work flawlessly when heavy memory load is generated by CPU. 32bpp
colors were used in the test. On BBB the video mode used 110MHz pixel
clock. The mode supported by the panel of am335x-evm uses 30MHz pixel
clock.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
|
|
| |
Signed-off-by: Christian Riesch <christian@riesch.at>
Cc: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Cc: Christoph Rüdisser <christoph.ruedisser@omicronenergy.com>
|
|
|
|
|
|
|
|
|
|
| |
The GPIO7 pad mux should be programmed to POWERHOLD value
as per board design. In cases where the PMIC is shut off the
mux is set to GPIO7 mode. So during initialization to be on the
safer side set the mode to POWERHOLD.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
|
| |
This reverts commit 3edc0c252257e4afed163a3a74aba24a5509b198, reversing
changes made to bb135a0180c31fbd7456021fb9700b49bba7f533.
|
|\ |
|
| |
| |
| |
| |
| |
| | |
With origin files there was an issue with serdes setting for SCSI.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
| | |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The dram_init* functions for the zynq board are not safe for use from
the board_init_f stage due to its use of the 'tmp' static variable.
This incorrect use of a static variable was causing rare issues where
the dram_init function would overwrite some parts the __rel_dyn section
which caused obscure failures.
Using the zynq_zybo configuration, U-Boot would generate the following
error during image load. This was caused due to dram_init overwriting
the relocations for the "image" variable within the do_bootm function.
Out of coincidence the un-initialized memory has a compression type
which is the same as the value for the relocation type R_ARM_RELATIVE.
Uncompressing Invalid Image ... Unimplemented compression type 23
It should be noted that this is just one way the issue could surface,
other cases my not be observed in normal boot flow.
This change removes the existing code and copies the implementation of
the dram_init and dram_init_banksize from the
arch/arm/mach-uniphier/dram_init.c source. This version of these
functions does not use static variables and behaves the same (reading
banks from fdt, and using the first bank as the ram_size).
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Fixes: 758f29d0f8 ("ARM: zynq: Support systems with more memory banks")
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch also includes ARM64 zynqmp changes:
- Remove platform non DM initialization
- Remove hardcoded sata base address
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Series-to: sjg, agraf@suse.de
Series-cc: uboot
Series-version: 4
Series-changes: 2
- make ceva_init_sata static
- Move SATA_CEVA to defconfig
- Initalized max_lun and max_id platdata
Series-changes: 3
- Extend Kconfig help description
- sort dm.h
- Remove SPL undefinition from board file
- Fix Kconfig dependecies
|
| |
| |
| |
| |
| |
| |
| | |
With the acquisition of Altera by Intel, my Altera email may be going
away soon. Update the contact to a more reliable address.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|/
|
|
|
|
|
|
| |
Add CycloneV based Terasic DE1-SoC board. The board boots
from SD/MMC. Ethernet and USB host is supported.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marek Vasut <marex@denx.de>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Baltos devices provide a mPCIe slot, whose power is turned off by
default. This patch activates mPCIe slot in U-Boot, so that for example
GSM modem can be already available in user space.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| | |
Remove unneeded pinmux configurations and TI EEPROM struct.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The bootrom may corrupt the area of SRAM used to store the ti_common_eeprom
structure. This patch makes sure that it's always read after a reset, even
if a valid MAGIC number is found in the SRAM.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|\ \
| |/
|/| |
|
| |
| |
| |
| |
| |
| |
| |
| | |
These are the last two samsung boards that don't use DM_I2C. Move them
over, leaving #ifdefs to allow the maintainer to complete this work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Three boards are still not converting to use DM_I2C. They are also using
the old PMIC framework. Rather than removing them, add #ifdefs to allow
them to continue to build. This will give the maintainers a little more
time to decide whether to convert them or not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch adds the necessary files to support the Marvell Armada 8k
devel board. Most board specfic files are shared with the Armada 7k
boards under the name "armada-8k*". So only minimal changes are
necessary to add this basic board support (except the DT files of
course).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch uses of_machine_is_compatible() to detect the board at runtime
and only configured the I2C IO expander for the xHCI power / reset on
the DB-88F7040 board. As this code will be used by other Armada-7k/8k
ports, its necessary to use this runtime detection here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This moves some of the Armada DB-88F7040 board specific files to a more
generic name: armada-8k. This is in preparation for the Armada-8k
support which will be added soon. And since both platforms share
most devices, lets also share most source files to not duplicate
the code here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| | |
Instead of using EXTRA options in defconfig, use two targets
in Kconfig to select correct SoC.
Signed-off-by: York Sun <york.sun@nxp.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Apparently the indentation is wrong in this case, as the second message
should be printed indepdently of the if statement.
Fix this indentation to avoid both compiler warnings and puzzled readers.
Pointed out by GCC 6.2's -Wmisleading-indentation warning.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add initial DTS support for AM571-IDK evm.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The AM571x Industrial Development Kit (IDK) is a board based on TI's
AM571x SoC which has a single core 1.5GHz Cortex-A15processor. This
board is a development platform for the Industrial Market with:
- 1GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector
The PRU/ICSS will be supported by 3rd party software for EtherCat,
Profibus, and other Industrial protocols.
The link to the data sheet and TRM can be found here:
http://www.ti.com/product/AM5718
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_idk_v1p3b_sr2p0 that were autogenerated on
20th October, 2016 by "Steve Kipisz <s-kipisz2@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_gp_evm_A3a_sr2p0 that were autogenerated on
19th October, 2016 by "Ahmad Rashed<a-rashed@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Update the timing for RGMII0 interface based on
PCT_DRA75x_DRA74x_SR1.1_v1.3.10 version (Jan 2016). This update
is for SR1.1
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
BeagleBoard-X15 Rev B1 with SR1.1 platform have incompatible changes for HDMI
GPIO requiring new dtb support. This implies we have to properly identify
the platform now as well. Hence provide a different board name for the
Rev B1 variants.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
AM57xx evm Rev A3 with SR2.0 platform have incompatible changes for HDMI
GPIO requiring new dtb support. This implies we have to properly identify
the platform now as well. Hence provide a different board name for the
Rev A3 variations.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| | |
Add DT support for dra71-evm and built it as part of FIT image.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add the pmic_data for LP873x PMIC which is used to power
up dra71x-evm.
Note: As per the DM[1] DRA71x supports only OP_NOM. So, updating
the efuse registers only to use OPP_NOM irrespective of any
CONFIG_DRA7_<VOLT>_OPP_{NOM,od,high} is defined.
[1] http://www.ti.com/product/DRA718/technicaldocuments
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Rev C version of EVM does require IODelay to be configured for RGMII
pins in MANUAL_1 configuration. Update the same based on PG2.0 initial
simulation values.
Data based on PCT_DRA72x_SR2.0_SR1.0_v1.3.0.7
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Add mux and iodelay settings for dra71x-evm.
Data generated using PCT_DRA71x_SR2.0_v1.0.0.0 version (June 2016).
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The dra71x-evm is a board based on TI's DRA718 processor targeting BOM-optimized
entry infotainment systems such as display audio and is a software compatible
derivative of the highly successful DRA74 and DRA72 processor families.
More information can be found here[1].
Add epprom detection for dra71-evm.
[1] http://www.ti.com/product/dra718
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
It can be expected that different paper spins of a SoC can have
different definitions for OPP and can have their own constraints
on the boot up OPP for each voltage rail. In order to have this
flexibility, add support for dynamically selecting the OPP voltage
based on the board to handle any such exceptions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Populate the corresponding TEE image processing call to be
performed during FIT loadable processing.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Populate the corresponding TEE image processing call to be
performed during FIT loadable processing.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
NAND SPL boot was missing. Add it. The README specific to omapl138-lcdk
is also removed because its content does not apply anymore, i.e. the
generated AIS image can be flashed directly to the NAND without
using any external tool to create and bootable AIS image.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The list of available boot method is not part of the binary which
prevent the SPL from booting u-boot or Linux.
Add the missing .u_boot_list* sections to the binary to fix it.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Verification has to be done before booting any images on HS devices. So
default the boot to FIT on HS devices.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Verification has to be done before booting any images on HS devices. So
default the boot to FIT on HS devices.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Verification has to be done before booting any images on HS devices. So
default the boot to FIT on HS devices.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Generic board support assumes a different method of specifying
DRAM size on board, also it can be shared among all boards, notably
only sh7763rdp board has a custom legacy dram_init(), however
the difference is only in printing some additional information,
this feature can be removed.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Reference lowlevel_init of all supported SH2A/SH3/SH4/SH4A boards
from a shared linker script, the lowlevel_init function will be called
by a relative address.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|