summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
* MLK-13925-1 mx7ulp_evk: Update LPDDR3 script to V1.4Ye Li2017-04-05-18/+4
| | | | | | | | | | | | | | | | | | | | Update LPDDR3 script from v1.2 to v1.4 EVK_IMX7ULP1_LPDDR3_320MHz_1GB_32bit_V1.4.inc with the changes below: Version 1.3 -Update the precharge command to CMD=01 at the DDR initialization phase Version 1.4 -remove unimplemented registers Write data bit delay --refer to the DDR_TRIM bits in IOMUXC1_DDR_SW_PAD_CTL_PAD_DDRn File: http://compass.freescale.net/livelink/livelink?func=ll&objid=235761218&objAction=browse&sort=name&viewType=1 Test: One EVK board passes overnight stress test. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit e3343cb38eac2cc69b58247b5adcb500e5f19834)
* MLK-13924 mx7ulp: Fix APLL num and denom setting issueYe Li2017-04-05-24/+1
| | | | | | | | | | | | | For the current APLL setting, as we want the APLL PFD0 to meet DDR clock 320Mhz requirement. We set MULT to 20, NUM to 4 and DENOM to 2, to get final 22 multiplier. But according to the RM, the NUM should always be less than the DENOM. So our setting violates the rule. Actually the ROM has already set the MULT to 22 and leave NUM/DENOM in default value. The calculated APLL PFD0 clock is 318.9888Mhz, which also meet the DDR requirement. To fix the issue, we remove the PLL settings in DCD to use default value from ROM, and only set the PFD0 FRAC. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 8cc70b1ded5309dee522aa00b43bd702a209ba51)
* imx: imx7ulp: add EVK board supportPeng Fan2017-04-05-0/+438
| | | | | | | | | | | | | | | | | | | | | | | | Add EVK board support. Add the evk dts file. LOG: U-Boot 2017.03-rc2-00038-gab86c1d (Feb 22 2017 - 15:59:58 +0800) CPU: Freescale i.MX7ULP rev1.0 at 500 MHz Reset cause: POR Boot mode: Dual boot Model: NXP i.MX7ULP EVK DRAM: 1 GiB MMC: FSL_SDHC: 0 In: serial@402D0000 Out: serial@402D0000 Err: serial@402D0000 Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* MLK-14419-3 imx: mx7d_arm2: add 19x19 LPDDR2/LPDDR3/DDR3 ARM2 supportPeng Fan2017-04-05-0/+2626
| | | | | | | | | Add 19x19 LPDDR2/LPDDR3/DDR3 ARM2 board supports. Enable the OF_CONTROL and convert them to use DM driver. Since the DTB lacks the support for some modules. We have to use QSPI and FEC with non-DM driver. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14419-2 imx: mx7d_arm2: add 12x12 ddr3 arm2 board supportPeng Fan2017-04-05-0/+644
| | | | | | | | Add 12x12 ddr3 arm2 board support and convert it to use OF_CONTROL and DM drivers. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14419-1 imx: mx7d_arm2: add 12x12 lpddr3 arm2 supportPeng Fan2017-04-05-0/+1493
| | | | | | | | Add mx7d 12x12 lpddr3 arm2 support, which has enabled the OF_CONTROL and DM drivers Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14418-13 imx: mx7dsabresd: Update Misc codesYe Li2017-04-05-6/+15
| | | | | | | | 1. Add BMODE support 2. Update environment variables to align with v2016.03 3. Remove the wdog WCR bit 4 clear. Since we have implemented reset_cpu for mx7d. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14418-12 imx: mx7dsabresd: Update LCD splash screen codesYe Li2017-04-05-10/+27
| | | | | | | Update LCD setup codes to use the parameters structure used for all i.mx platforms, discard to use videmode environment variable. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14418-10 imx: mx7dsabresd: update ddr script and add plugin supportPeng Fan2017-04-05-0/+360
| | | | | | Update ddr script and add plugin support. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* MLK-14418-9 imx: mx7dsabresd: add nand/qspi boot supportPeng Fan2017-04-05-0/+4
| | | | | | | | | | Add nand/qspi build configurations for their boot support. Also Add gpmi-nand and qspi specified DTS files for enable them. For QSPI, this patch changes it to use DM driver. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14418-8 imx: mx7dsabresd: add epdc supportPeng Fan2017-04-05-0/+235
| | | | | | | | Add epdc support from v2016.03. Add a epdc specified DTS file for using epdc Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14418-7 imx: mx7dsabresd: add FEC DM supportPeng Fan2017-04-05-49/+92
| | | | | | | | Add FEC2 and convert to use FEC DM driver. Add board rev check. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14418-6 imx: mx7dsabresd: switch to DM USBPeng Fan2017-04-05-25/+0
| | | | | | Switch to use DM USB. Enable GPIO regulator to handle vbus supply. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* MLK-14418-5 imx: mx7dsabresd: reset ENET_RST_BPeng Fan2017-04-05-0/+16
| | | | | | | | Reset ENET_RST_B to make ENET function stable. Since DM_GPIO enabled, we use "gpio_spi@0_5" which corresponds to ENET_RST_B. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* MLK-14418-4 imx: mx7dsabresd: enable dm driversPeng Fan2017-04-05-256/+15
| | | | | | | Enable GPIO/I2C/MMC/SPI/74X164 DM drivers. Discard mxc spi support. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* MLK-13132: mx6qarm2: mt128x64mx32: adjust ahb/axi podf dividersAdrian Alonso2017-04-05-1/+1
| | | | | | | | | Adjust ahb/axi clock root podf dividers to be divided by 1 to allow ahb/axi clock root to be 24Mhz when sourced from osc_clk. Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com> (cherry picked from commit 9e80234c823d6a2a0d9e10ab4c4c605bf646bd22)
* MLK-14499 mx6qarm2: Convert to use OF_CONTROL and DM driverYe Li2017-04-05-48/+33
| | | | | | | | | Modify the mx6qarm2 configurations to enable OF_CONTROL and DM drivers: USB, Ethernet, UART and MMC. Add two DTS files for imx6q/dl arm2 board and imx6q pop arm2 board. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14391-3 mx6sxarm2: Convert to enable OF_CONTROL and DM driversYe Li2017-04-05-56/+253
| | | | | | | | | | | | | | | Update mx6sx 14x14/17x17/19x19 lpddr2/ddr3 arm2 board codes and build configurations to enable OF_CONTROL and DM drivers. 1. Update GPIO codes for adding gpio request 2. Enable USB DM driver 3. Update PMIC code for using DM PMIC 4. Add spinor/qspi/nand/eimnor boot support. 5. Add defconfig for using plugin. 6. Enable Ethernet DM driver 7. Update for using QSPI DM driver Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14391-1 mx6sxarm2: Add mx6sx 14x14/17x17/19x19 arm2 board codesYe Li2017-04-05-0/+2825
| | | | | | | | Copy the board codes and build configurations for i.MX6SX 14x14/17x17/19x19 ARM2 boards from v2016.03 as the base for converting to OF_CONTROL and DM driver. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14390-3 mx6sllarm2: Convert to enable OF_CONTROL and DM driversYe Li2017-04-05-5/+34
| | | | | | | | | | | | Update mx6sll lpddr2/3 arm2 board codes and build configurations to enable OF_CONTROL and DM drivers. 1. Update GPIO codes for adding gpio request 2. Enable USB DM driver 3. Update PMIC code for using DM PMIC 4. Add spinor boot support, pin conflict with LCD, will disable LCD. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14390-1 mx6sllarm2: Add mx6sll LPDDR2/3 ARM2 board codesYe Li2017-04-05-0/+1309
| | | | | | | Move the mx6sll lpddr2/3 arm2 board codes and defconfigs from v2016.03 as the base for converting to use DTB OF_CONTROL. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14380-3 mx6ullarm2: Convert to enable OF_CONTROL and DM driversYe Li2017-04-05-16/+145
| | | | | | | | | | | | | | | Update mx6ull ddr3 arm2 board codes and build configurations to enable OF_CONTROL and DM drivers. 1. Update QSPI settings and codes for DM QSPI driver. 2. Update GPIO codes for adding gpio request 3. Enable FEC DM driver and update relevant configurations 4. Enable USB DM driver 5. Update PMIC and LDO by-pass codes for DM PMIC 6. Add various boot media support, QSPI/NAND/SPINOR 7. Add rework support for eMMC/QSPIB/TSC Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-13602-3 mx6ullevk/arm2: Enable module fuse checking for mx6ull boardsYe Li2017-04-05-0/+11
| | | | | | | | | Enable the module disable fuse checking configurations, and ENET fuse checking during ENET setup. Signed-off-by: Ye Li <ye.li@nxp.com> Tested-by: Bai Ping <ping.bai@nxp.com> (cherry picked from commit d2192a3909be8ab9433082e7c04c917489b28e25)
* MLK-12929 imx6ull: support splash screen for epdcRobby Cai2017-04-05-0/+221
| | | | | | | | add splash screen feature for epdc. it's tested on imx6ull arm2 board. Signed-off-by: Robby Cai <robby.cai@nxp.com> (cherry picked from commit bcdbe240bb2a97d38ba30dd244a51ece87662b06)
* MLK-14380-1 mx6ullarm2: Add mx6ull DDR3 ARM2 board codesYe Li2017-04-05-0/+1115
| | | | | | | Move the mx6ull ddr3 arm2 board codes and defconfigs from v2016.03 as the base for converting to use DTB OF_CONTROL. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14382-3 mx6ularm2: Convert to enable OF_CONTROL and DM driversYe Li2017-04-05-39/+282
| | | | | | | | | | | | | | Update mx6ul ddr3 arm2 and lpddr2 arm2 boards codes and build configurations to enable OF_CONTROL and DM drivers. 1. Update QSPI settings and codes for DM QSPI driver. 2. Update GPIO codes for adding gpio request 3. Enable FEC DM driver and update relevant configurations 4. Enable USB DM driver 5. Update PMIC and LDO by-pass codes for DM PMIC 6. Add various boot media support, QSPI/NAND/SPINOR/EIMNOR Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14382-1 mx6ularm2: Add DDR3 and LPDDR2 ARM2 board codesYe Li2017-04-05-0/+2399
| | | | | | | Move the mx6ul DDR3/LPDDR2 ARM2 boards codes from v2016.03 u-boot as the base for OF_CONTROL enabling. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14326-14 mx6ulevk: Enable OF_CONTROL and DM driversYe Li2017-04-05-3/+94
| | | | | | | | | | | | | | | | Update mx6ulevk board files and build configurations to enable OF_CONTROL and DM drivers. 1. QSPI settings and codes update for using DM QSPI driver. For DM and non-DM driver, the AMBA address is not same. 2. Update configurations for DM i2c driver, using CONFIG_SYS_I2C for non-DM driver 3. GPIO update for adding gpio_request 4. Add FEC DM driver support for two FEC controllers. 5. Enable USB DM driver. 6. Enable 74X164 DM driver for 74LV controlling. 7. Enable PMIC DM driver for 9x9 EVK Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14326-11 mx6slevk: Enable OF_CONTROL and DM driversYe Li2017-04-05-1/+90
| | | | | | | | | | | | Update mx6slevk board files and build configurations to enable OF_CONTROL and DM drivers. 1. Update PMIC and LDO-bypass codes for DM PMIC driver. 2. Update configurations for DM i2c driver 3. GPIO update for adding gpio_request 4. Remove duplicated configurations from build config Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14326-9 mx6sxsabreauto: Update board file and build configurationYe Li2017-04-05-3/+9
| | | | | | | Enable FEC, USB and QSPI DM driver in build configuration and update board file for them. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14326-7 mx6sxsabresd: Enable OF_CONTROL and DM driversYe Li2017-04-05-4/+111
| | | | | | | Update mx6sxsabresd board files and build configurations to enable OF_CONTROL and DM drivers. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14326-3 mx6qsabreauto: Enable OF_CONTROL and DM driverYe Li2017-04-05-54/+230
| | | | | | | | | | | | | | Enable OF_CONTROL and DM driver on mx6qsabreauto. 1. Add the imx6qsabreauto relevant DTS file for using DTB. 2. Modify PMIC initialization codes to use DM PMIC driver. 3. Modify to use PCA953X DM driver 4. Remove NAND from default, since the default imx6q-sabreauto.dts disabled the nand. The pins are conflicted with UART3, while UART3 is enabled. 5. For NAND build configuration, remove the USB, since the imx6q-sabreauto-gpmi-weim.dts will have pin conflicts on steer logic. 6. GPIO requests added. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14375-3 mx6ullevk: Add 9x9 EVK board supportYe Li2017-04-05-0/+314
| | | | | | | | | | | | | | 1. Add build configs for i.MX6ULL 9X9 EVK. Enable DM I2C driver and DM PMIC driver for pfuze3000. Convert power init codes to use DM PMIC driver. 2. Add lpddr2 script IMX6ULL_9X9_LPDDR2_400MHz_16bit_V1.2.inc for the 9x9 board. Refer the commit 44a84b44a84cd1bdcc54d722987e5f109510891b 3. Add DTS file for 9x9 evk board. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14375-1 mx6ullevk: Update board codes to align with v2016.03Ye Li2017-04-05-3/+256
| | | | | | | | | | | | | | | | | | Update mx6ull evk to add features from v2016.03. 1. Add support for NAND flash. 2. Add support for QSPI DM driver. 3. Add USB DM driver support. 4. Add two FEC support by using DM FEC driver 5. Update environments for various boot devices support: SD/NAND/eMMC/QSPI 6. Add MFGtool environments. 7. Add board codes for 9x9 EVK board For the DTS file, some changes are needed for using QSPI DM driver 1. Add spi0 alias for qspi node. Which is used for bus number 0. 2. Modify the n25q256a@0 compatible property to "spi-flash". 3. Modify spi4 (gpio_spi) node to spi5 Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14366 mx6sllevk: Update board codes to align with v2016.03Ye Li2017-04-05-0/+6
| | | | | | | | | | Update mx6sll EVK board codes for features: 1. Add SD/MMC dynamical device detect. 2. Add wdog set for kernel. 3. Add mfgtool environments. 4. Modify SD/MMC environment offset. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14363 mx6qsabreauto: Fix ethernet PHY setting issueYe Li2017-04-05-0/+33
| | | | | | | | | | | The PHY settings for RGMII has been removed from mx6qsabreauto board codes, due to the atheros PHY driver have updated to use same configuration for AR8031 and AR8035, while this configuration is duplicated as we set in board codes. But in recent codes, the PHY driver added a patch for AR8031 independent config. So needs to add the PHY settings back to the board codes. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-12996 imx: mx6dqp/dq: Fix SATA read/write fail after booting from SATAYe Li2017-04-05-4/+14
| | | | | | | | | | | | | | | We found a issue in PLL6 ENET that changing the bit[1:0] DIV_SELECT for ENET ref clock will impact the SATA ref 100Mhz clock. If SATA is initialized before this changing, SATA read/write can't work after it. And we have to re-init SATA. The issue can reproduce on both i.MX6DQP and i.MX6DQ. IC investigation is ongoing. This patch is an work around that moves the ENET clock setting (enable_fec_anatop_clock) from ethernet init to board_init which is prior than SATA initialization. So there is no PLL6 change after SATA init. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit fd8fbf7fa0b10199ac89cd13cae851149f51accb)
* MLK-12791 mx6qpsabresd: Change ENET TXCLK clock from PLLYe Li2017-04-05-0/+10
| | | | | | | | | | | | | In u-boot, i.MX6QP sabresd board uses 125Mhz ref clock from PHY, While kernel uses the clock from internal PLL by setting GPR5 bit 9. When doing warm reset in kernel, the GPR regigster is not reset, so the clock source still is the PLL. This causes ENET in u-boot can't work. In this patch, we change the u-boot to use internal PLL to align with kernel for i.MX6QP. This also fixes the ENET issue after kernel warm reset. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 7f00c72e17e4e440df62aa4945a619fdbc9cfd8f)
* MLK-12442: imx: mx6qarm2: lpddr2 set dram 2 channel fixed modeAdrian Alonso2017-04-05-2/+12
| | | | | | | | | | | | | | Setup MMDC in two channel fixed mode Initialize dram banks for two channel fixed mode DRAM bank = 0x00000000 -> start = 0x10000000 -> size = 0x20000000 DRAM bank = 0x00000001 -> start = 0x80000000 -> size = 0x20000000 Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com> (cherry picked from commit bf1d8faf1dab7c4245ba7b79ceef6279cff45625)
* MLK-12555-2 mx6ulevk: Enable the Watchdog WDOG_B signal outputYe Li2017-04-05-0/+2
| | | | | | | | | When using watchdog timeout in kernel, the reset does not output the WDOG_B signal, so the power supply won't be reset. To solve the problem, we enable it in u-boot. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 8a713e8cd1500ecc6daa02a14a63763a548095b4)
* MLK-12555 mx6sxsabreauto: Enable the Watchdog WDOG_B signal outputYe Li2017-04-05-0/+3
| | | | | | | | | When using watchdog timeout in kernel, the reset does not output the WDOG_B signal, so the power supply won't be reset. To solve the problem, we enable it in u-boot. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 7b53ee014c9f02f6ead0b60d5295d07205247a7c)
* MLK-11230 imx6: USB: Modify OTG ID pin pad setting to pull upYe.Li2017-04-05-6/+31
| | | | | | | | | | | Set the ID pin pad to pull up not the pull down at default, otherwise we can't enter the device mode, but always detect as host. After this change we have to use portA cable to play as host, and use portB cable for device. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit b315d6b36a913d75d25284320e69050ebdf7a7eb)
* MLK-12531 mx6sxsabresd: Add CM4 fast boot up demoYe Li2017-04-05-0/+19
| | | | | | | | | | | | | | | | | | This is a demo that CM4 will boot up by u-boot without typing any command. It boots up at u-boot early init, try to minimize the time from power up to the CM4 running. Since CM4 runs on QSPI NOR XIP, we have to disable the QSPI driver in u-boot to avoid conflict. RDC for shared GPIO1 is added, but not enabled, because the kernel is not ready for shared GPIO1. Users can uncomment the CONFIG_IMX_RDC to enable it. Some legacy codes in mx6sxsabreauto are removed. We only need this work on mx6sxsabresd as a demo. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit f66842f79d4e33ace45762466eed23a86d367642)
* MLK-12493-1 Add support for various boot deviceYe Li2017-04-05-10/+69
| | | | | | | | | | Add support for various boot devices like NAND, QSPINOR, SPINOR, eMMC, EIMNOR, SATA. Modify board level files to support the feature and add corresponding defconfig files Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 72c35e80b86f7f75a52db45959793882bb730793)
* MLK-12500-2 HAB: Add commented secure boot configurationsYe Li2017-04-05-0/+56
| | | | | | | | | | | | CONFIG_SECURE_BOOT is used for signed image building, this configuration is not enabled at default. Comment it in mx6/mx7 common header file. Users can uncomment it to enable. Also add CONFIG_CSF_SIZE for defining the CSF reserved size and resize the CONFIG_CSF_SIZE to 0x4000 to align with v2016.03. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 01cc7d9bc205251c13712418d51f3a4d7b20861b)
* MLK-12495 mx6: Add LDO bypass supportYe Li2017-04-05-0/+406
| | | | | | | | | | | | | | | | Port LDO bypass support from v2015 to support the features: 1. Add check for 1.2GHz core speed. If Speed grading fuse is for 1.2GHz, enable LDO bypass and setup PMIC voltages. LDO bypass is dependent on the flatten device tree file. 2. We set WDOG_B in set_anatop_bypass() before, because it is the only case, but now on i.mx6sabreauto board, we didn't use ldo-bypass mode, but have to use WDOG_B to reboot whole board, so split these code to independent function so that board file can call it freely. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 5b87d04dba66fa45375d59648838ef89f559f75d)
* MLK-12436-17: imx: mx6sxsabreauto: update board and headerYe Li2017-04-05-24/+8
| | | | | | | | | | | | Align with imx_v2016.03 1. Update pmic settings to enable SD3 power and use PMIC common init codes. 2. Enable bmode. 3. Update MMC root parameters 4. Update AUXBOOT for M4 Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit 0816a496fbe3f7d0e4f1a9322c76908a5c557c8c) Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-12436-16: imx: mx6sxsabresd: update board and headerPeng Fan2017-04-05-17/+135
| | | | | | | | | | | | | | Align with imx_v2016.03. Add emmc support which needs board rework. Add I2C2. Update pmic settings. Add bmode. Move partial code from board_early_init_f to board_init. Add PCI power and reset GPIO and disable PCI at default. Update QSPI settings. Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit 9613a2d07760f56b3c93779b14ad32ef69856da7)
* MLK-12436-12: mx6slevk: update board codePeng Fan2017-04-05-4/+88
| | | | | | | | | | | | | | Add elan code, to handle epdc which has i2c devices. In imx_v2015.04, the two pathces are for elan. b6ba68516b681a38025252bd0ef6a6ed3e8adfa0 MLK-10215 Add elan init in i.MX6SL-EVK board 0c600f6a67f00fe0c674c08c355bea3789109679 MLK-10885 imx: mx6slevk ignore elan init when no epdc on board Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit cb249aa1d57788c52145d28f2e2c68cb320d8ae3) Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-12436-10: mx6sabresd: update board code and header fileYe Li2017-04-05-22/+138
| | | | | | | | | | | Align board code and header file with imx_v2016.03. Update pmic settings for i.MX6QP. wrap spi code together using CONFIG_MXC_SPI macro. To i.MX6SOLO, need to define nosmp in bootargs. Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit bb35d09d140efc7ff9b74bbcd77d7827c1dd503e) Signed-off-by: Ye Li <ye.li@nxp.com>
generated by cgit v1.1 at 2024-09-13 07:00:14 +0000