summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
...
| * | da850evm : enable NAND even when not in NAND boot modeBen Gardiner2010-10-17-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is currently no NAND pinmux enabled by the da850evm board setup code. This is fine when booting from NAND since the early boot code (UBL) will setup the pinmux; however, when the boot mode is any other setting NAND is unusable when enabled in the config. This patch adds a pinmux list for NAND and enables it when NAND is enabled in the config. Tested by booting from SPI on the da850evm and verifying NAND was usable. Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> CC: Nick Thompson <nick.thompson@ge.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | OMAP3: Add support for the OMAP3 IGEP module.Enric Balletbo i Serra2010-10-17-0/+301
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The IGEP module is a low-power, high performance production-ready system-on-module (SOM) based on TI's OMAP3 family.The IGEP module solution based upon TI OMAP3 provides a low-power/low-cost platform for a variety of consumer/industrial/medical devices. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | OMAP3: Add support for the IGEP v2 board.Enric Balletbo i Serra2010-10-17-0/+367
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The IGEP v2 board is a low-cost, fan-less and industrial temperature range single board computer that unleashes laptop-like performance and expandability without the bulk, expense, or noise of typical desktop machines. Its architecture shares much in common with other OMAP3 boards. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com> Acked-by: Steve Sakoman <steve.sakoman@linaro.org> Tested-by: Steve Sakoman <steve.sakoman@linaro.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | ARMV7: OMAP4: Implement relocation for Panda and OMAP4430SDPSteve Sakoman2010-10-17-5/+2
| | | | | | | | | | | | | | | | | | | | | This patch fixes the build breakage introduced by the recent relocation changes for ARMV7 Signed-off-by: Steve Sakoman <steve@sakoman.com>
| * | ARMV7: OMAP3: Implement relocation for OveroSteve Sakoman2010-10-17-1/+1
| | | | | | | | | | | | | | | | | | | | | This patch fixes the build breakage introduced by the recent relocation changes for ARMV7 Signed-off-by: Steve Sakoman <steve@sakoman.com>
| * | ARMV7: OMAP4: Use generic mmc driver on OveroSteve Sakoman2010-10-17-0/+9
| | | | | | | | | | | | | | | | | | This patch switches from the legacy mmc driver to the new generic mmc driver Signed-off-by: Steve Sakoman <steve@sakoman.com>
| * | ARMV7: OMAP4: Use generic mmc driver on BeagleSteve Sakoman2010-10-17-0/+9
| | | | | | | | | | | | | | | | | | This patch switches from the legacy mmc driver to the new generic mmc driver Signed-off-by: Steve Sakoman <steve@sakoman.com>
| * | ARMV7: OMAP4: Use generic mmc driver on SDP4430Sukumar Ghorai2010-10-17-0/+10
| | | | | | | | | | | | | | | | | | | | | This patch switches from the legacy mmc driver to the new generic mmc driver Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com> Tested-by: Steve Sakoman <steve@sakoman.com>
| * | ARMV7: OMAP4: Use generic mmc driver on PandaSukumar Ghorai2010-10-17-0/+9
| | | | | | | | | | | | | | | | | | | | | This patch switches from the legacy mmc driver to the new generic mmc driver Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com> Tested-by: Steve Sakoman <steve@sakoman.com>
| * | Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk2010-10-17-3/+142
| |\ \
| | * | mx51evk: add u-boot.imx to ALL targetLoic Minier2010-10-14-0/+1
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Loic Minier <loic.minier@linaro.org> CC: stefano babic <sbabic@denx.de>
| | * | MX31: Add USB Host support to the QONG boardStefano Babic2010-10-13-0/+33
| | | | | | | | | | | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
| | * | MX31: Add support to update FPGA bitstreamStefano Babic2010-10-13-3/+108
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds the possibility to update the QONG FPGA (a Lattice XP2-5E) with u-boot using some GPIOs to drive the JTAG interface. Signed-off-by: Stefano Babic <sbabic@denx.de>
* | | | Fix define for MPC5121 ADS board.mark.vels@team-embedded.nl2010-10-13-2/+2
|/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Originally the Makefile defines CONFIG_ADS5121_REV2 when configuring for board mpc5121ads_rev2. The config in include/configs/mpc5121ads.h expects a define CONFIG_MPC5121ADS_REV2 for this. Therefore there are two defines used but only 1 is defined. This patch renames references to CONFIG_ADS5121_REV2 to CONFIG_MPC5121ADS_REV2 to have one common define. This patch fixes faulty mem size detection caused by wrong config in include/configs/mpc5121ads.h Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
* | | Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2010-10-13-193/+1422
|\ \ \ | | |/ | |/|
| * | board/armltd/integrator/split_by_variant.sh: fix 'echo -n'Andreas Bießmann2010-10-13-72/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes an error when running MAKEALL for ARM9. On OS X /bin/sh uses builtin echo which does not utilise '-n' switch. GNU manual for builtins recomend to use here-document style to solve this portability issue. This patch removes the usage of 'echo -n' and replace by here-document style or a oneline echo command. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> CC: Peter Pearse <peter.pearse@arm.com>
| * | ARMV7: Versatile Express Coretile CortexA9x4 supportMatt Waddel2010-10-13-0/+357
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the ARM quad-core Cortex-A9 processor This system includes a motherboard(Versatile Express), daughterboard (Coretile), and SOC(Cortex-A9 quad core). The serial port, ethernet, and flash systems work with these additions. The naming convention is: SOC -> CortexA9 quad core = ca9x4 daughterboard -> Coretile = ct motherboard -> Versatile Express = vxp This gives ca9x4_ct_vxp.c as the board support file. Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
| * | Kirkwood: dram_init is moved to dram.cPrafulla Wadaskar2010-10-13-55/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For all Kirkwood boards so far dram_init function is duplicated dram_init function is moved to dram.c and relevant code from all board specific files removed If any board needs specific dram init handling than standard one, then, a macro CONFIG_SYS_BOARD_DRAM_INIT should be defined in board config header file and the dram_init function can be put in board specific source file For ex. keymile boards Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
| * | Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk2010-10-11-66/+1008
| |\ \ | | |/
| | * MX51: Support for TTECH vision2 boardStefano Babic2010-10-07-0/+993
| | | | | | | | | | | | | | | | | | | | | | | | The patch adds support for TTECH vision2 board. The board has 512MB RAM, SDHC slot and 4MB SPI device from StMicron. Signed-off-by: Stefano Babic <sbabic@denx.de>
| | * MX51: Drop unused header file for mx51evkStefano Babic2010-09-29-52/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | As stated in 272017853339f5b9685f9488bdaf5405812d12a4, the mx51evk has not CPLD and all references must be removed. This patch drop a .h file that still remains in board directory. Signed-off-by: Stefano Babic <sbabic@denx.de>
| | * Use common function to set GPIOs for MX3 and MX5Stefano Babic2010-09-29-14/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds support for setting gpios to the MX51 processor and change name to the corresponding functions for MX31. In this way, it is possible to get rid of nasty #ifdef switches related to the processor type. Signed-off-by: Stefano Babic <sbabic@denx.de>
* | | ppmc7xx: Use _start as reset entry pointPeter Tyser2010-10-12-4/+3
| | | | | | | | | | | | | | | | | | | | | | | | Previously the _warm_start label was used as an entry point. These 2 entry points should be functionally identical after the removal of the BOOTFLAG_WARM define. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* | | a4m072: support for SHOW_BOOT_PROGRESS feature using LED displayIlya Yanok2010-10-12-5/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for displaying boot progress codes on a4m072 board using LED display. As we can display only one symbol at any time on the hardware (two symbols with blinking) we can't display progress codes directly and have to map them to 2-symbol codes. We use the following mapping on the a4m972 board: [1, 8] U [100, 108] -> 5 [-9, -1] U [-101, -100] U [-113, -103] -> -5 [9, 14] U [120, 123] U [125, 129] -> 8 [-13, -10] U [-122, -120] U [-127, -124] U {-129} -> -8 {15} -> 9 [-32, -30] -> -A [-40, -35] U [-51, -42] U [-58, -53] U [-83, -80] U {-64, -130, -140, -150} -> -B Other progress code are ignored. One symbol codes are displayed steady while two-symbol codes are displayed using blinking. Boot progress codes are displayed with decimal got unset (as opposed to 'display' command output). Signed-off-by: Ilya Yanok <yanok@emcraft.com>
* | | a4m072: led display supportIlya Yanok2010-10-12-0/+174
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for LED display on a4m072 board. Hardware is capable of displaying only one symbol at any time. We support displaying two symbols in software (via blinking). Signed-off-by: Ilya Yanok <yanok@emcraft.com>
* | | A4M072: Added support for the board.Sergei Poselenov2010-10-12-0/+389
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch provides support for the A4M072 board with the following features: UART NOR flash FEC Ethernet External SRAM I2C EEPROM CompactFlash cards on IDE/ATA port USB Host PCI initialization The 7-segment LED indicator is not yet supported. Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
* | | pdm360ng: add EDID property to FDT display nodeAnatolij Gustschin2010-10-12-0/+43
| | | | | | | | | | | | | | | | | | | | | | | | PDM360NG board uses this functionality to pass display timing info to the Linux Framebuffer driver. Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
* | | Merge branch 'master' of git://git.denx.de/u-boot-microblazeWolfgang Denk2010-10-12-0/+13
|\ \ \
| * | | microblaze: Add support for NET_MULTI apiMichal Simek2010-10-12-0/+13
| |/ / | | | | | | | | | | | | | | | Microblaze hasn't supported NET_MULTI support. Signed-off-by: Michal Simek <monstr@monstr.eu>
* | | davinci_emac: davinci_eth_set_mac_addr to ->write_hwaddrBen Gardiner2010-10-11-41/+22
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch proposes to migrate the davinci_emac driver to using the eth_device->write_hwaddr function pointer as suggested by Ben Warren. All the davinci boards had the behaviour, prior to this patch, of sync'ing the environment variable enetaddr with the MAC address read from non-volatile storage on boot -- when the two locations disagreed, the environment variable value took precendence. This patch keeps the same behaviour but lets eth_initialize take care of it. This patch refactors davinci_emac setup in the boards so that the MAC address is read from non-volatile storage into the environment variable and then the environment variable value is use in eth_intialize. The only exception is the direct call to davinci_eth_set_mac_addr made by the da830evm board init which was changed into an assignment of the enetaddr field. Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Tested-by: Nick Thompson <nick.thompson@ge.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-x86Wolfgang Denk2010-10-11-51/+33
|\ \
| * | x86: Use loops instead of memcpy/memset in board_init_fGraeme Russ2010-10-07-1/+2
| | | | | | | | | | | | | | | | | | | | | Provides a small speed increase and prepares for fully relocatable image. Downside is the TEXT_BASE, bss, load address etc must ALL be aligned on a a 4-byte boundary which is not such a terrible restriction as everything is already 4-byte aligned anyway
| * | x86: Rearrange linker scriptGraeme Russ2010-10-07-21/+18
| | | | | | | | | | | | Tidy up the linker script and discard some sections to save space
| * | x86: Rename linker script symbolsGraeme Russ2010-10-07-12/+9
| | | | | | | | | | | | Create more generic names for the symbols exported from the linker script
| * | x86: Remove usage of %ebp as a return pointerGraeme Russ2010-10-07-3/+2
| | | | | | | | | | | | Using %ebp as a return pointer prevents creating 'load anywhere' images
| * | x86: Remove progress indication in low-level initGraeme Russ2010-10-07-12/+0
| | | | | | | | | | | | | | | Progress indication is not relocation friendly so remove it in preperation for full relocatability support
| * | x86: use gc sections to reduce image sizeGraeme Russ2010-10-07-5/+5
| | | | | | | | | | | | | | | Follow the discussion of Charles Manning and Mike Frysinger. Using gc_sections helps reduce image size.
| * | x86: Use TEXT_BASE in linker scriptsGraeme Russ2010-10-07-4/+4
| | | | | | | | | | | | | | | | | | Use TEXT_BASE rather than a hard-coded base address on x86 linker scripts. This will allow any board to define its base link address without having to modify the linker script
* | | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2010-10-11-28/+168
|\ \ \
| * | | fsl: add support for NXID v1 EEPROM formatTimur Tabi2010-10-07-9/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Freescale application note AN3638 describes an update to the NXID format, which stores MAC addresses and related data on an on-board EEPROM. The new version adds support for up to 23 MAC addresses, instead of just 8. Since the initial implementation of NXID had a "0" in the 'version' field, this new version is called "v1". Boards that are shipped with EEPROMs in the NXID v1 format should define CONFIG_SYS_I2C_EEPROM_NXID_1 instead of CONFIG_SYS_I2C_EEPROM_NXID. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | | powerpc/85xx: Add support for 4th PCI controller on corenet_dsKumar Gala2010-10-07-1/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | We configure the controller but dont have virtual address space thus any devices on the 4th controller are not accessible in u-boot. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | | fsl: verify writes to the MAC address EEPROMTimur Tabi2010-10-07-1/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Update the code which writes to the on-board EEPROM so that it can detect if the write failed because the EEPROM is write-protected. Most of the 8xxx-class Freescale reference boards use an AT24C02 EEPROM to store MAC addresses and similar information. With this patch, if the EEPROM is protected, the "mac save" command will display an error message indicating that the write has not succeeded. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | | p1022ds: add audclk hwconfig setting to enable codec reference clockTimur Tabi2010-10-07-9/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Freescale P1022DS can use either a 12.288MHz or a 11.2896MHz reference clock for the audio codec, but by default both are disabled. Add a 'audclk' hwconfig option that allows the user to choose which clock he wants. The 12.288MHz clock allows the codec to use sampling rates of 16, 24, 32, 48, 64, and 96KHz. The 11.2896 clock allows 14700, 22050, 29400, 44100, 58800, and 88200Hz. Also configure a pin muxing to select some SSI signals, which will disable I2C1. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | | mpc8569mds: fix some ddr settingsHaiying Wang2010-10-07-3/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable half drive strength, set RTT to 60Ohm and set write leveling override. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | | mpc8569mds: fix consuming long time while relocating code.Haiying Wang2010-10-07-5/+36
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The original code maps boot flash as non-cacheable region. When calling relocate_code in flash to copy u-boot from flash to ddr, every loop copy command is read from flash. The flash read speed will be the bottleneck, which consuming long time to do this operation. To resovle this, map the boot flash as write-through cache via tlb. And set tlb to remap the flash after code executing in ddr, to confirm flash erase operation properly done. Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | board/mpl: Remove mpl-specific memory test commandPeter Tyser2010-10-06-598/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The mpl-specfic memory test is only documented for one board, doesn't compile cleanly, uses improper coding style, and overlaps functionality with U-Boot's common 'mtest' command, so lets get rid of it. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> CC: d.peter@mpl.ch CC: d.mueller@elsoft.ch CC: wd@denx.de
* | | CCM: remove code for yet another corpseWolfgang Denk2010-10-06-1487/+0
| | | | | | | | | | | | | | | | | | | | | The CCM board has long reached EOL, and support for it is no longer relevant in current versions of U-Boot. Remove it. Signed-off-by: Wolfgang Denk <wd@denx.de>
* | | PCU_E: remove code for yet another corpseWolfgang Denk2010-10-06-1597/+0
| | | | | | | | | | | | | | | | | | | | | The PCU_E board has long reached EOL, and support for it is no longer relevant in current versions of U-Boot. Remove it. Signed-off-by: Wolfgang Denk <wd@denx.de>
* | | pm9g45: fix compile warningWolfgang Denk2010-10-06-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix warning: pm9g45.c: In function 'pm9g45_macb_hw_init': pm9g45.c:99: warning: unused variable 'pio' Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Ilko Iliev <iliev@ronetix.at>
* | | pm9263: fix compile warningWolfgang Denk2010-10-06-1/+0
|/ / | | | | | | | | | | | | | | | | | | Fix warning: pm9263.c: In function 'pm9263_macb_hw_init': pm9263.c:99: warning: unused variable 'pio' Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Ilko Iliev <iliev@ronetix.at>
generated by cgit v1.1 at 2024-11-14 03:53:05 +0000