summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
* omap3evm: Set environment variable 'ethaddr'Sanjeev Premi2011-11-03-0/+15
| | | | | | | | | It is now responsibility of the board specific init code to set the environment variable corresponding to the MAC address. Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILDHeiko Schocher2011-11-03-1/+1
| | | | | Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* arm/km: adapt bootcounter evaluationHolger Brunck2011-11-03-5/+27
| | | | | | | | | | | | | | The bootcounter (stored in the RAM) is not enough protected with the 4 Bytes BOOTCOUNT_MAGIC against bit errors due to short power loss or holding a system in RESET. It has been seen, that the bootcounter value has been changed due to a bit flip on a system holding in RESET, but the BOOTCOUNT_MAGIC was still valid. A bit pattern with 4000 bytes (after BOOTCOUNT_MAGIC) has been implemented, which should be enough to detect a bit error. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: trigger reconfiguration for the Xilinx FPGAHolger Brunck2011-11-03-1/+6
| | | | | | | | | | The Xilinx FPGA must be reconfigured each time the unit reboots. The FPGA is connected to the GPIO pin 39 from kirkwood. This patch triggers this pin for km_kirkwood_pci targets. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boardsValentin Longchamp2011-11-03-5/+0
| | | | | | | | | | | | | | We got dropped from Linux mach-types.h because of a lack of mainline support and this is needed since the last Linux/u-boot mach-types synchro. This patch also defines CONFIG_MACH_TYPE for all keymile boards, as this is a mandatory CONFIG for ARM boards now. The initialization of gd->bd->bi_arch_number is removed form km_arm.c, our board file. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* netspace_v2: fix SDRAM configurationSimon Guinot2011-11-03-2/+164
| | | | | | | | | | | | Network Space (Max) v2 and Internet Space v2 boards have different SDRAM configuration and size: respectively 256MB (DDR2 1Gb, 128Mbx8 organisation) and 128MB (DDR2 512Mb, 64Mbx8 organisation). To handle the differences, this patch add a dedicated kwimage.cfg file for Internet Space v2. Additionnaly the number of SDRAM banks is fixed. Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
* arm/km/mgcoge3un: enhance "waitforne" featureHolger Brunck2011-11-03-1/+10
| | | | | | | | | | The mgcoge3un waits to be released from mgcoge3ne at startup. This patch enhances this feature with the possibility to interrupt this wait if a key is pressed. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* ARM: dreamplug: fix compilationAnatolij Gustschin2011-11-03-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix build issues: mvrtc.c: In function 'rtc_get': mvrtc.c:45: warning: implicit declaration of function 'readl' mvrtc.c: In function 'rtc_set': mvrtc.c:100: warning: implicit declaration of function 'writel' dreamplug.c: In function 'board_early_init_f': dreamplug.c:43: warning: implicit declaration of function 'kw_config_gpio' dreamplug.c: In function 'board_init': dreamplug.c:108: warning: implicit declaration of function 'kw_sdram_bar' drivers/rtc/librtc.o: In function `rtc_set': /home/ag/u-boot/u-boot-move-new-host/u-boot-video/drivers/rtc/mvrtc.c:92: undefined reference to `writel' /home/ag/u-boot/u-boot-move-new-host/u-boot-video/drivers/rtc/mvrtc.c:103: undefined reference to `writel' drivers/rtc/librtc.o: In function `rtc_reset': /home/ag/u-boot/u-boot-move-new-host/u-boot-video/drivers/rtc/mvrtc.c:117: undefined reference to `readl' /home/ag/u-boot/u-boot-move-new-host/u-boot-video/drivers/rtc/mvrtc.c:120: undefined reference to `readl' drivers/rtc/librtc.o: In function `rtc_get': /home/ag/u-boot/u-boot-move-new-host/u-boot-video/drivers/rtc/mvrtc.c:45: undefined reference to `readl' /home/ag/u-boot/u-boot-move-new-host/u-boot-video/drivers/rtc/mvrtc.c:48: undefined reference to `readl' ... Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Jason Cooper <u-boot@lakedaemon.net> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Marek Vasut <marek.vasut@gmail.com>
* ARM: DockStar: fix compilationAnatolij Gustschin2011-11-03-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | Fix build problem: mvgbe.c: In function 'mvgbe_initialize': mvgbe.c:735: warning: implicit declaration of function 'get_random_hex' dockstar.c: In function 'board_early_init_f': dockstar.c:43: warning: implicit declaration of function 'kw_config_gpio' dockstar.c: In function 'board_init': dockstar.c:113: warning: implicit declaration of function 'kw_sdram_bar' dockstar.c: In function 'set_leds': dockstar.c:161: warning: implicit declaration of function 'readl' dockstar.c:161: error: dereferencing pointer to incomplete type dockstar.c:162: warning: implicit declaration of function 'writel' dockstar.c:162: error: dereferencing pointer to incomplete type dockstar.c:163: error: dereferencing pointer to incomplete type dockstar.c:164: error: dereferencing pointer to incomplete type make[1]: *** [dockstar.o] Error 1 make: *** [board/Seagate/dockstar/libdockstar.o] Error 2 Reported-by: Roland Kletzing <devzero@web.de> Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Prafulla Wadaskar <prafulla@marvell.com>
* ARM: netspace_v2: fix warningsAnatolij Gustschin2011-11-03-0/+1
| | | | | | | | | | | | | | | Fix compiler warnings when compiling for netspace_v2, netspace_max_v2 and inetspace_v2: netspace_v2.c: In function 'board_early_init_f': netspace_v2.c:37: warning: implicit declaration of function 'kw_config_gpio' netspace_v2.c: In function 'board_init': netspace_v2.c:86: warning: implicit declaration of function 'kw_sdram_bar' Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Simon Guinot <simon.guinot@sequanux.org> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Marek Vasut <marek.vasut@gmail.com>
* misc:pmic:samsung Enable PMIC driver at C210 Universal targetŁukasz Majewski2011-11-03-0/+5
| | | | | | | | Enable support for PMIC driver at C210 Universal reference target. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* smdkv310: use macro for mmc data read function addressChander Kashyap2011-11-03-7/+8
| | | | | | | | | | board/samsung/smdkv310/mmc_boot.c: Removed the typedef for "mmc data read API (copy_sd_mmc_to_mem)" as it is used only once and replaced hard-coded API address value by macro. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* smdkv310: use spl framework for mmc splChander Kashyap2011-11-03-1/+194
| | | | | | | | smdkv310 board was using mmc_spl framework for mmc spl support. This patch migrates the framework from mmc_spl to spl. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* SMDKV310: use get_ram_size() to validate dram sizeChander Kashyap2011-11-03-4/+8
| | | | | | | | | smdkv310.c: in dram_init_banksize(void) function dram size was initialized without validation. get_ram_size() function will validate the bank size before initialization. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* SMDKV310: Initialize board id using CONFIG_MACH_TYPEChander Kashyap2011-11-03-1/+0
| | | | | | | Use CONFIG_MACH_TYPE generic macro to initialize board id. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* ORIGEN : use absolute paths and fix tool namingAngus Ainslie2011-11-03-3/+3
| | | | | | | | | | On some hosts using relative paths will cause the build to fail. This patch sets absolute paths for the tools directory Get rid of MSDOS style excecutable extension Signed-off-by: Angus Ainslie <angus.ainslie@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* MX25: tx25: Fix building due to missing MACH_TYPEStefano Babic2011-11-03-1/+0
| | | | | | | | Added MACH_TYPE for the tx25 to the configuration file. The MACH_TYPE is dropped from mach-types.h after last sync with kernel. Signed-off-by: Stefano Babic <sbabic@denx.de>
* mx31: Add board support for HALE TT-01Helmut Raiger2011-11-03-0/+283
| | | | | | | | | This adds basic board support for TT-01 based on the Bluetechnix i.MX31 SOM. Currently only NOR-Flash boot is implemented. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Acked-by: Stefano Babic <sbabic@denx.de>
* MX35: add support for flea3 boardStefano Babic2011-11-03-0/+417
| | | | | | | | The flea3 board is a custom board by CarMediaLab used in automotive. Network (FEC), NOR, NAND and SPI are supported. Signed-off-by: Stefano Babic <sbabic@denx.de>
* vision2: Remove unused header fileFabio Estevam2011-11-03-1/+0
| | | | | | errno.h is not used on this file, so remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx51evk: Remove unused get_board_rev functionFabio Estevam2011-11-03-9/+0
| | | | | | No board information is passed for MX51EVK, so remove get_board_rev function. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx51evk: Use GPIO API for configuring the IOMUXFabio Estevam2011-11-03-5/+3
| | | | | | | | GPIO API provides mxc_request_iomux function for setting the IOMUX mode. Use this function instead of directly writing to the IOMUX register. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* qong: remove unneeded IOMUX settingsFabio Estevam2011-11-03-6/+0
| | | | | | | | | | | | | On qong board some of the USBH2 pins are set via GPR register, so don need to setup the IOMUX for each pin individually. Other than that, these pins should not be configured as primary function because the primary function selects SSI functionality. Let GPR register do the work and remove the unneeded IOMUX setup. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* qong: Use mx31_set_gpr to setup USBH2 pinsFabio Estevam2011-11-03-1/+1
| | | | | | Instead of writing directly to the GPR register, use mx31_set_gpr to setup USBH2 pins. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx31pdk: Add MC13783 PMIC supportFabio Estevam2011-11-03-0/+12
| | | | | | | | | | | Add MC13783 PMIC support. Tested by using the 'date' command, which reads the MC13783 RTC registers: MX31PDK U-Boot > date Date: 1970-01-01 (Thursday) Time: 2:22:35 Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* MX35: added ESDC structure to imx-regsStefano Babic2011-11-03-18/+0
| | | | | | | | The structure and PLL defines are added to the imx-regs.h file and dropped from board header files. Signed-off-by: Stefano Babic <sbabic@denx.de>
* Reduce build timesWolfgang Denk2011-11-03-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | U-Boot Makefiles contain a number of tests for compiler features etc. which so far are executed again and again. On some architectures (especially ARM) this results in a large number of calls to gcc. This patch makes sure to run such tests only once, thus largely reducing the number of "execve" system calls. Example: number of "execve" system calls for building the "P2020DS" (Power Architecture) and "qong" (ARM) boards, measured as: -> strace -f -e trace=execve -o /tmp/foo ./MAKEALL <board> -> grep execve /tmp/foo | wc -l Before: After: Reduction: ================================== P2020DS 20555 15205 -26% qong 31692 14490 -54% As a result, built times are significantly reduced, typically by 30...50%. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Andy Fleming <afleming@gmail.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Albert Aribaud <albert.aribaud@free.fr> cc: Graeme Russ <graeme.russ@gmail.com> cc: Mike Frysinger <vapier@gentoo.org> Tested-by: Graeme Russ <graeme.russ@gmail.com> Tested-by: Matthias Weisser <weisserm@arcor.de> Tested-by: Sanjeev Premi <premi@ti.com> Tested-by: Simon Glass <sjg@chromium.org> Tested-by: Macpaul Lin <macpaul@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
* board/prodrive/p3mx/mv_eth.c: fix GCC 4.6 build warningsWolfgang Denk2011-11-03-27/+6
| | | | | | | | | | | | | | | | | | | | | | | Fix: mv_eth.c: In function 'mv64460_eth_real_open': mv_eth.c:471:6: warning: variable 'port_status' set but not used [-Wunused-but-set-variable] mv_eth.c: In function 'mv64460_eth_stop': mv_eth.c:722:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable] mv_eth.c: In function 'mv64460_eth_xmit': mv_eth.c:796:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable] mv_eth.c: In function 'mv64460_eth_receive': mv_eth.c:877:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable] mv_eth.c: In function 'mv64460_eth_get_stats': mv_eth.c:979:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable] mv_eth.c: In function 'mv64460_eth_update_stat': mv_eth.c:1006:24: warning: variable 'dummy' set but not used [-Wunused-but-set-variable] mv_eth.c:1005:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable] mv_eth.c: In function 'mv64460_eth_print_stat': mv_eth.c:1087:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable] mv_eth.c: In function 'eth_clear_mib_counters': mv_eth.c:2141:15: warning: variable 'dummy' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
* board/g2000/strataflash.c: fix GCC 4.6 build warningsWolfgang Denk2011-11-03-3/+0
| | | | | | | | | Fix: strataflash.c: In function 'flash_write_cfiword': strataflash.c:669:11: warning: variable 'ctladdr' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
* board/jse/flash.c: fix GCC 4.6 build warningsWolfgang Denk2011-11-03-14/+1
| | | | | | | | | | | Fix: flash.c: In function 'flash_erase': flash.c:304:24: warning: variable 'l_sect' set but not used [-Wunused-but-set-variable] In addition, remove some dead code. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-mmcWolfgang Denk2011-11-03-12/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-mmc: tegra2: Move MMC clock initialization into MMC driver mmc: sdhci: fix sdma bug for large file transfer mmc: sdhci: add timeout for data transfer mmc: sdhci: add mmc structure for host mmc: sdhci: fix build warning mmc: sdhci: fix cache flush mmc: CMD7:MMC_CMD_SELECT_CARD response fix mmc: test mmc bus width on startup mmc: change magic number to macro define mmc: mv_sdhci: fix 8bus width access for 88SV331xV5 mmc: retry the cmd8 to meet 74 clocks requirement in the spec PXA: Add MMC driver using the generic MMC framework
| * tegra2: Move MMC clock initialization into MMC driverStephen Warren2011-11-03-12/+1
| | | | | | | | | | | | | | | | | | | | | | This centralizes knowledge of MMC clocking into the MMC driver. This also removes clock setup from the board files, which will simplify later changes that modify the Harmony board to support the correct set of MMC controllers. Signed-off-by: Stephen Warren <swarren@nvidia.com> Cc: Andy Fleming <afleming@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* | x86: Rename include/asm/ic to include/asm/arch-sc520Graeme Russ2011-11-02-5/+3
|/ | | Also include some trivial related cleanups
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2011-10-28-374/+1441
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-arm: ARM: Add Calxeda Highbank platform dkb: make mmc command as default enabled Marvell: dkb: add mmc support ARM: pantheon: add mmc definition davinci: remove config.mk file from the sources ARM:AM33XX: Add support for TI AM335X EVM ARM:AM33XX: Added timer support ARM:AM33XX: Add emif/ddr support ARM:AM33XX: Add clock definitions ARM:AM33XX: Added support for AM33xx omap3/emif4: fix registers definition davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM davinci: emac: add support for more than 1 PHYs davinci: emac: add new features to autonegotiate for EMAC da850evm: Move LPSC configuration to board_early_init_f() omap4_panda: Build in cmd_gpio support on panda omap: Don't use gpio_free to change direction to input mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset OMAP3: overo : Add environment variable optargs to bootargs OMAP3: overo: Move ethernet CS4 configuration to execute based on board id OMAP3: overo : Use ttyO2 instead of ttyS2. da830: add support for NAND boot mode dm36x: revert cache disable patch dm644X: revert cache disable patch devkit8000: Add malloc space omap: spl: fix build break due to changes in FAT OMAP3 SPL: Provide weak omap_rev_string omap: beagle: Use ubifs instead of jffs2 for nand boot omap: overo: Disable pull-ups on camera PCLK, HS and VS signals omap: overo: Configure mux for gpio10 SPL: Add DMA library omap3: Add interface for omap3 DMA omap3: Add DMA register accessors omap3: Add Base register for DMA arm, davinci: add missing LSPC define for MMC/SD1 U-Boot/SPL: omap4: Make ddr pre-calculated timings as default. DaVinci: correct MDSTAT.STATE mask omap4: splitting padconfs into common, 4430 and 4460 omap4: adding revision detection for 4460 ES1.1 omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL gplug: fixed build error as a result of code cleanup patch kirkwood_spi: add dummy spi_init() gpio: mvmfp: reduce include platform file ARM: orion5x: reduce dependence of including platform file serial: reduce include platform file for marvell chip ARM: kirkwood: reduce dependence of including platform file ARM: armada100: reduce dependence of including platform file ARM: pantheon: reduce dependence of including platform file Armada100: Add env storage support for Marvell gplugD Armada100: Add SPI flash support for Marvell gplugD Armada100: Add SPI support for Marvell gplugD SPI: Add SPI driver support for Marvell Armada100 dreamplug: initial board support. imx: fix coding style misc: pmic: drop old Freescale's pmic driver MX31: mx31pdk: use new pmic driver MX31: mx31ads: use new pmic driver MX31: mx31_litekit: use new pmic driver MX5: mx53evk: use new pmic driver MX5: mx51evk: use new pmic driver MX35: mx35pdk: use new pmic driver misc: pmic: addI2C support to pmic_fsl driver misc: pmic: use I2C_SET_BUS in pmic I2C MX5: efikamx/efikasb: use new pmic driver MX3: qong: use new pmic driver RTC: Switch mc13783 to generic pmic code MX5: vision2: use new pmic driver misc: pmic: Freescale PMIC switches to generic PMIC driver misc:pmic:samsung Enable PMIC driver at GONI target misc:pmic:max8998 MAX8998 support at a new PMIC driver. misc:pmic:core New generic PMIC driver mx31pdk: Remove unneeded config mx31: provide readable WEIM CS accessor MX51: vision2: Set global macros I2C: Add i2c_get/set_speed() to mxc_i2c.c ARM: Update mach-types devkit8000: Add config to enable SPL MMC boot devkit8000: protect board_mmc_init arm, post: add missing post_time_ms for arm cosmetic, post: Codingstyle cleanup arm, logbuffer: make it compileclean tegra2: Enable MMC for Seaboard tegra2: Add more pinmux functions tegra2: Rename PIN_ to PINGRP_ tegra2: Add more clock functions tegra2: Clean up board code a little tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
| * ARM: Add Calxeda Highbank platformRob Herring2011-10-27-0/+106
| | | | | | | | | | | | | | | | | | Add basic support for Calxeda Highbank platform. Only minimal support with serial and SATA are included. Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
| * Marvell: dkb: add mmc supportLei Wen2011-10-27-0/+43
| | | | | | | | Signed-off-by: Lei Wen <leiwen@marvell.com>
| * ARM:AM33XX: Add support for TI AM335X EVMChandan Nath2011-10-27-0/+393
| | | | | | | | | | | | | | | | | | This patch adds basic support for booting the board. This patch adds support for the UART necessary to get to the u-boot prompt. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * da850evm: Move LPSC configuration to board_early_init_f()Christian Riesch2011-10-27-9/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit f1d2b313c9eb6808d30c16a9eb5251240452a56c the serial port of the da850evm is accessed before the UART2 peripheral of the SoC is powered on in the function board_init() in board/davinci/da8xxevm/da850evm.c. When u-boot is used in conjunction with the UBL (user boot loader, see doc/README.davinci) on this board, the UART2 peripheral is already turned on by UBL at the time u-boot is started. Hence, the wrong initialization sequence is not noticed by most users. However, if UBL is not used, u-boot must power on the peripheral before using it. This patch adds a board_early_init_f() function for the LPSC configuration to the da850evm board configuration. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Heiko Schocher <hs@denx.de> Cc: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * omap: Don't use gpio_free to change direction to inputJoe Hershberger2011-10-27-14/+1
| | | | | | | | | | | | | | | | | | gpio_free() should not have the side effect of setting the line to input since this prevents the gpio command from being able to set a line as output. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * OMAP3: overo: Move ethernet CS4 configuration to execute based on board idPhilip Balister2011-10-27-4/+3
| | | | | | | | | | | | | | | | | | | | | | By moving the CS4 configuration into the board specific configuration, it is left free for custom carrier boards. The USRP-E1XX series uses CS4 to control access to an FPGA, so without this patch the device driver cannot claim CS4. Signed-off-by: Philip Balister <philip@opensdr.com> Tested-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * da830: add support for NAND boot modeManjunath Hadli2011-10-27-0/+63
| | | | | | | | | | | | | | | | | | | | | | | | Add support for enabling NAND boot mode in configuration file and add correspanding pinmux support, nand initialize function in board file. The size required for environment variables not more than 10KB the CONFIG_ENV_SIZE is set to 10KB from (512 << 10). Acked-by: Nick Thompson <nick.thompson@ge.com> Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * omap: overo: Disable pull-ups on camera PCLK, HS and VS signalsSteve Sakoman2011-10-27-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | The level shifters used on the Caspa camera module have a 4k output impedance. Combined with the 100uA pull-up resistors in the OMAP3, this raises the ground level to 400mV. Adding crosstalk between the pixel clock and the HS/VS signals on the flat cable (a ground line in between would have been nice), logic 0 levels can raise up to 650mV. This exceeds the camera input pins VIL maximum voltage. This change suggested-by Laurent Pinchart Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * omap: overo: Configure mux for gpio10Steve Sakoman2011-10-27-1/+1
| | | | | | | | | | | | | | | | | | | | This pad was previously configured for sysclkout_1. This patch changes the configuration to gpio_10 to reduce radiated noise from the 26Mhz clock, as well as make the pin more generally useful. Signed-off-by: Steve Sakoman <steve@sakoman.com> Acked-by: Philip Balister <philip@opensdr.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * omap4: splitting padconfs into common, 4430 and 4460Ricardo Salveti de Araujo2011-10-27-2/+29
| | | | | | | | | | | | | | | | | | | | Not all padconfs are the same between 4430 and 4460, so instead of working around this with an if, we should have an specific padconf structure for both chips (like handling the differences between the LEDs GPIOs and TPS). Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * gplug: fixed build error as a result of code cleanup patchPrafulla Wadaskar2011-10-27-0/+1
| | | | | | | | Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
| * ARM: kirkwood: reduce dependence of including platform fileLei Wen2011-10-27-0/+6
| | | | | | | | | | | | | | | | | | | | | | For files like the drivers/serial/serial.c, it must include the platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the definition in the platform definition files. Include the platform definition file in the config file, so that it would decouple the dependence for the driver files. Signed-off-by: Lei Wen <leiwen@marvell.com>
| * ARM: armada100: reduce dependence of including platform fileLei Wen2011-10-27-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | For files like the drivers/serial/serial.c, it must include the platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the definition in the platform definition files. Include the platform definition file in the config file, so that it would decouple the dependence for the driver files. Updated cpu.h to remove build errors for gplugd board (by prafulla) Signed-off-by: Lei Wen <leiwen@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
| * Armada100: Add SPI support for Marvell gplugDAjay Bhargav2011-10-27-0/+12
| | | | | | | | | | | | This patch add SPI driver support for Marvell gplugD Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
| * dreamplug: initial board support.Jason Cooper2011-10-27-0/+410
| | | | | | | | | | | | | | | | | | | | | | Copied wholeheartedly from board/Marvell/guruplug and modified to add support for SPI NOR flash. CONFIG_MACH_DREAMPLUG defined in include/configs/dreamplug.h until Linus's kernel.org tree adds it to mach-types.h. Once it trickles down, the definition can be removed from include/configs/dreamplug.h. Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
| * imx: fix coding styleFabio Estevam2011-10-27-11/+11
| | | | | | | | | | | | | | | | | | Fix checkpatch warning and errors in several i.MX related files. While at it also address a checkpatch warning at arch/arm/cpu/armv7/mx5/soc.c regarding the usage of extern in a C file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
generated by cgit v1.1 at 2024-11-08 13:29:16 +0000