summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
...
* | powerpc: T2080RDB: Remove macro CONFIG_T2080RDBYork Sun2017-01-04-1/+1
| | | | | | | | | | | | Use TARGET_T2080RDB from Kconfig instead. Signed-off-by: York Sun <york.sun@nxp.com>
* | powerpc: T2080QDS: Remove macro T2080QDSYork Sun2017-01-04-12/+12
| | | | | | | | | | | | Use TARGET_T2080QDS from Kconfig instead. Signed-off-by: York Sun <york.sun@nxp.com>
* | powerpc: T1024RDB: Remove macro CONFIG_T1024RDBYork Sun2017-01-04-10/+10
| | | | | | | | | | | | | | | | Use TARGET_T1024RDB from Kconfig instead. Signed-off-by: York Sun <york.sun@nxp.com> [trini: Get missing hunk in board/freescale/t102xrdb/ddr.c] Signed-off-by: Tom Rini <trini@konsulko.com>
* | powerpc: T1023RDB: Remove macro CONFIG_T1023RDBYork Sun2017-01-04-10/+10
|/ | | | | | Use TARGET_T1023RDB from Kconfig instead. Signed-off-by: York Sun <york.sun@nxp.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2017-01-02-4/+46
|\
| * udoo: neo: Fix indentationFabio Estevam2017-01-02-2/+2
| | | | | | | | | | | | The standard way is to put ifdef/endif in the very first column. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
| * imx6ul: geam6ul: Add MAINTAINERS for nand_defconfigJagan Teki2017-01-02-0/+1
| | | | | | | | | | | | | | | | | | Add Jagan as MAINTAINERS of configs/imx6ul_geam_nand_defconfig Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * mx6qsabreauto: Fix the EIM clock for the mx6qp variantFabio Estevam2017-01-02-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the MX6Q the aclk_eim_slow_podf field is '1' after POR, while on the MX6DQP it is '3'. This makes the EIM clock to be only 66MHz on the mx6qp variant, instead of 132 MHz. Instead of relying on the POR values for the CSMR1 register, make sure to manually configure the clk_eim_slow_sel field as '00' so that EIM clock is derived from AXI clock and the aclk_eim_slow_podf field as '1' so that EIM clock can be AXI clock divided by 2. This way a consistent EIM clock frequency is configured for all the mx6 variants. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
| * ARM: imx7s-warp: enable USB gadget ethernetKevin Hilman2017-01-02-0/+14
| | | | | | | | | | | | | | | | | | Enable USB gadget ethernet by default to have networking capabilities. Tested using DHCP and TFTP to transfer kernel, DT, ramdisk. Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
| * udoo_neo: Remove USDHC3 entryFabio Estevam2017-01-02-2/+1
| | | | | | | | | | | | | | | | Commit c94981efa20cc58 ("udoo_neo: Remove USDHC3 support") removed the SDHC3 support, but missed to remove the entry from the usdhc_cfg structure, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
* | arm: am57xx: cl-som-am57x: add ETH supportDmitry Lifshitz2017-01-02-0/+223
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add MAC support. Use PHY, connected to RGMII1 as a default Eth adapter, by appropriate setting of 'cpsw_data.active_slave'. 'cpsw_phy' env variable can override this setting. Set the MAC addresses in the U-Boot environment. The addresses are retrieved from the on-board EEPROM or from the SOC's MAC fuses. Set the following PHYs RGMII clock delays: - Enable RX delay - Disable TX delay Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> [uri.mashiach@compulab.co.il: add RGMII clock delays] Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@konsulko.com>
* | arm: am57xx: cl-som-am57x: fetch board rev from EEPROMDmitry Lifshitz2017-01-02-0/+14
| | | | | | | | | | | | | | | | | | | | | | Add PCB revision message. Implement board revision get_board_rev API. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Commit description update. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@konsulko.com>
* | arm: am57xx: cl-som-am57x: add initial board supportDmitry Lifshitz2017-01-02-0/+429
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Features supported : * Serial console * SPI Flash * MMC/SD Card * eMMC storage * SATA * PCA9555 - GPIO expander over I2C5 bus * USB Use spl alternate boot device feature to define fallback to the main boot device as it is defined by hardware. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> [uri.mashiach@compulab.co.il: Adjust to v2016.11] Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* | digsy_mtc.c: Minor spelling/grammar fixes.Robert P. J. Day2017-01-02-2/+2
|/ | | | Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
* mmc: move some SDHCI related options to KconfigMasahiro Yamada2016-12-29-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While I moved the options, I also renamed them so that they are all prefixed with MMC_SDHCI_. This commit was created in the following steps. [1] Rename with the following command find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e ' s/CONFIG_MMC_SDMA/CONFIG_MMC_SDHCI_SDMA/g s/CONFIG_BCM2835_SDHCI/CONFIG_MMC_SDHCI_BCM2835/g s/CONFIG_KONA_SDHCI/CONFIG_MMC_SDHCI_KONA/g s/CONFIG_MV_SDHCI/CONFIG_MMC_SDHCI_MV/g s/CONFIG_S5P_SDHCI/CONFIG_MMC_SDHCI_S5P/g s/CONFIG_SPEAR_SDHCI/CONFIG_MMC_SDHCI_SPEAR/g ' [2] create the Kconfig entries in drivers/mmc/Kconfig [3] Move the options by the following command tools/moveconfig.py -y MMC_SDHCI_SDMA MMC_SDHCI_BCM2835 \ MMC_SDHCI_KONA MMC_SDHCI_MV MMC_SDHCI_S5P MMC_SDHCI_SPEAR [4] Sort drivers/mmc/Makefile for readability Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: move CONFIG_SDHCI to Kconfig, renaming to CONFIG_MMC_SDHCIMasahiro Yamada2016-12-29-1/+1
| | | | | | | | | | | | | | | | | | | | | | | Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI. My motivation for the rename is, ultimately, to make all the MMC options prefixed with MMC_ and SDHCI options with MMC_SDHCI_, like Linux. This commit was created as follows: [1] Rename the config option with the following command: find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g' [2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig [3] run "tools/moveconfig.py -y MMC_SDHCI" [4] add "depends on MMC_SDHCI" to existing SDHCI driver entries Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* imx: mx6sllevk: add MAINTAINERS filePeng Fan2016-12-27-0/+7
| | | | | | | add MAINTAINERS files Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* board: samsung: update the MAINTAINERS fileJaehoon Chung2016-12-27-5/+5
| | | | | | Update the maintainer from Przemyslaw and Lukasz to me. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
* Update Maintainer and Author's email addressAjay Bhargav2016-12-27-3/+3
| | | | | | | | I am not longer using my old email address "ajay.bhargav@einfochips.com". For U-Boot development email address is now updated to contact@8051projects.net Signed-off-by: Ajay Bhargav <contact@8051projects.net>
* Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini2016-12-23-424/+1
|\
| * spi: Zap mpc52xx_spi.c, config and related codeJagan Teki2016-12-21-424/+1
| | | | | | | | | | | | | | | | | | armada100_spi.c, related config options and related codes are zapping becuase of "no DM conversion". Cc: Werner Pfister <Pfister_Werner@intercontrol.de> Signed-off-by: Jagan Teki <jagan@openedev.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM64: zynqmp: Replace board specific with generic memory bank decodingNathan Rossi2016-12-20-109/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The dram_init and dram_init_banksize functions were using a board specific implementation for decoding the memory banks from the fdt. This board specific implementation uses a static variable 'tmp' which makes these functions unsafe for execution from within the board_init_f context. This change makes the dram_init* functions use a generic implementation of decoding and populating memory bank and size data. Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Fixes: 8d59d7f63b ("ARM64: zynqmp: Read RAM information from DT") Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | ARM: zynq: Replace board specific with generic memory bank decodingNathan Rossi2016-12-20-109/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The dram_init and dram_init_banksize functions were using a board specific implementation for decoding the memory banks from the fdt. This board specific implementation uses a static variable 'tmp' which makes these functions unsafe for execution from within the board_init_f context. This unsafe use of a static variable was causing a specific bug when using the zynq_zybo configuration, U-Boot would generate the following error during image load. This was caused due to dram_init overwriting the relocations for the 'image' variable within the do_bootm function. Out of coincidence the un-initialized memory has a compression type which is the same as the value for the relocation type R_ARM_RELATIVE. Uncompressing Invalid Image ... Unimplemented compression type 23 It should be noted that this is just one way the issue could surface, other cases my not be observed in normal boot flow. Depending on the size of various sections, and location of relocations within __rel_dyn and the compiler/linker the outcome of this bug can differ greatly. This change makes the dram_init* functions use a generic implementation of decoding and populating memory bank and size data. Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Fixes: 758f29d0f8 ("ARM: zynq: Support systems with more memory banks") Cc: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | block: Move ceva driver to DMMichal Simek2016-12-20-11/+0
|/ | | | | | | | | This patch also includes ARM64 zynqmp changes: - Remove platform non DM initialization - Remove hardcoded sata base address Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-12-18-188/+6814
|\ | | | | | | | | | | Migrate CONFIG_ARCH_USE_MEMSET/MEMCPY with this merge. Signed-off-by: Tom Rini <trini@konsulko.com>
| * imx6: icorem6: Rename engicam icorem6 defconfig filesJagan Teki2016-12-16-14/+11
| | | | | | | | | | | | | | | | | | | | Rename defconfig files for better compatible with respective board names and dts files. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx6q: Add Engicam i.CoreM6 Solo/Duallite RQS Starter Kit initial supportJagan Teki2016-12-16-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from MMC: ------------- U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07) Trying to boot from MMC1 U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07 +0530) CPU: Freescale i.MX6DL rev1.3 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 DualLite/Solo RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl-rqs> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx6q: Add Engicam i.CoreM6 Quad/Dual RQS Starter Kit initial supportJagan Teki2016-12-16-0/+453
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from MMC: ------------- U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44) Trying to boot from MMC1 U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44 +0530) CPU: Freescale i.MX6D rev1.2 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl-rqs> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * imx6: geam6ul: Add NAND supportJagan Teki2016-12-16-0/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add NAND support for Engicam GEAM6UL board. Boot Log: -------- U-Boot SPL 2016.11-g537fa5f (Nov 28 2016 - 11:42:28) Trying to boot from NAND NAND : 256 MiB U-Boot 2016.11-g537fa5f (Nov 28 2016 - 11:20:06 +0100) CPU: Freescale i.MX6UL rev1.1 69 MHz (running at 396 MHz) CPU: Automotive temperature grade (-40C to 125C) at 42C Reset cause: WDOG Model: Engicam GEAM6UL DRAM: 128 MiB NAND: 256 MiB MMC: FSL_SDHC: 0 * Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx6ul: Add Engicam GEAM6UL Starter Kit initial supportJagan Teki2016-12-16-0/+298
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot Log: -------- U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30) Trying to boot from MMC1 U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530) CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 43C Reset cause: POR Model: Engicam GEAM6UL DRAM: 128 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 geam6ul> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * imx6: icorem6: Add framebuffer supportJagan Teki2016-12-16-0/+113
| | | | | | | | | | | | | | | | | | | | Add IPUv3 framebuffer support for Engicam i.CoreM6 qdl board. Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * icorem6: Use CONFIG_DM_ETH supportJagan Teki2016-12-16-71/+0
| | | | | | | | | | | | | | | | | | | | | | | | Use CONFIG_DM_ETH and remove board_eth_init code from board files. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx: add i.MX53 Beckhoff CX9020 Embedded PCPatrick Bruenn2016-12-16-0/+525
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add CX9020 board based on mx53loco. Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse serial_mxc with DTE and prepare for device tree migration of other functions and imx53 devices. The CX9020 differs from i.MX53 Quick Start Board by: - use uart2 instead of uart1 - DVI-D connector instead of VGA - no audio - CCAT FPGA connected to emi - enable rtc Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
| * imx: mx6sllevk: add plugin supportPeng Fan2016-12-16-0/+161
| | | | | | | | | | | | | | Add plugin support for mx6sllevk board. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
| * arm: imx: add i.MX6SLL EVK board supportPeng Fan2016-12-16-0/+270
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add i.MX6SLL EVK board support. 1. Add imx6sll-evk device tree. 2. Enable SDHC/I2C/UART. 3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver. Boot Log: U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800) CPU: Freescale i.MX6SLL rev1.0 at 792MHz CPU: Commercial temperature grade (0C to 95C)Reset cause: POR Model: Freescale i.MX6SLL EVK Board Board: MX6SLL EVK DRAM: 2 GiB i2c bus 0 at 35258368, no gpio pinctrl state. PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
| * imx: clock: gate clk before changing pix clk muxPeng Fan2016-12-16-2/+2
| | | | | | | | | | | | | | | | | | | | | | The LCDIF Pixel clock mux is not glitchless, so need to gate before changing mux. Also change enable_lcdif_clock prototype with a new input parameter to indicate disable or enable. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
| * board/liteboard: Add support for liteBoardMarcin Niestroj2016-12-16-0/+342
| | | | | | | | | | | | | | | | | | | | | | | | liteBoard is a development board which uses liteSOM as its base. Hardware specification: * liteSOM (i.MX6UL, DRAM, eMMC) * Ethernet PHY (id 0) * USB host (usb_otg1) * MicroSD slot (uSDHC1) Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
| * udoo_neo: Add Ethernet supportBreno Lima2016-12-16-0/+95
| | | | | | | | | | | | | | | | UDOO Neo boards has one FEC port connected to KSZ8091, add support for it. Tested on a UDOO Neo Full with "dhcp zImage" command. Signed-off-by: Breno Lima <breno.lima@nxp.com>
| * udoo_neo: Add PFUZE300 PMIC supportBreno Lima2016-12-16-0/+143
| | | | | | | | | | | | | | | | UDOO Neo boards has a PFUZE300 connected to I2C1 bus. Tested on a UDOO Neo Full with "pmic PFUZE3000 dump" command. Signed-off-by: Breno Lima <breno.lima@nxp.com>
| * udoo_neo: Staticize board_string()Breno Lima2016-12-16-1/+1
| | | | | | | | | | | | | | Change board_string() function to static because it's being used locally. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * udoo_neo: Remove USDHC3 supportBreno Lima2016-12-16-88/+6
| | | | | | | | | | | | | | | | It's not necessary to support USDHC3 in U-Boot as it's being used for the WLAN. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * arm: imx: initial support for colibri imx6Max Krummenacher2016-12-16-0/+2037
| | | | | | | | | | | | | | | | This adds board support for the Toradex module family Colibri iMX6. The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both with a version for commercial and industrial temperature range. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
| * arm: imx: initial support for apalis imx6Max Krummenacher2016-12-16-0/+2203
| | | | | | | | | | | | | | | | This adds board support for the Toradex module family Apalis iMX6. The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with commercial and industrial temperature range. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
| * colibri_vf: use same NAND clock as Linux usesStefan Agner2016-12-16-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently a divider of 6 has been used, leading to following NAND Flash Controller (NFC) clocks: VF61: 27.7 MHz (166.7MHz bus clock) VF50: 22 MHz (132MHz bus clock) The NAND Flash Memory used on VF50 allows to use clock speed of up to 33MHz, while the Flash Memory of VF61 allows 50MHz. We can use the same divider of 4 on both modules to configure the maximal possible clock speeds: VF61: 41.7 MHz VF50: 33 MHz Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
| * colibri_vf: cleanup USB clock initializationStefan Agner2016-12-16-4/+10
| | | | | | | | | | | | | | | | | | Use the same preprocessor define to enable clocks as we use to enable the driver. Make sure that the necessary PLL's are on (they get enabled by boot ROM by default, so this is more for completness). Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
| * colibri_vf: use device-tree for MTD partitionsStefan Agner2016-12-16-0/+13
| | | | | | | | | | | | | | | | Use device-tree fixup to communicate the MTD partitions to the kernel. U-Boot's mtdparts environment variable will be used as partition source for the device-tree based partition table too. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
| * toradex: allow custom fdt board setup in board fileStefan Agner2016-12-16-5/+53
| | | | | | | | | | | | | | | | | | | | The config block support currently uses the ft_board_setup function to patch the device tree with config block information. However, this does not allow to patch the device tree with board specific information. Rename the common setup function to ft_common_board_setup and use the call it from the board files directly. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
| * toradex: fix USB Download gadget fixup callbackStefan Agner2016-12-16-2/+2
| | | | | | | | | | | | | | Use the proper config option to guard the USB Download Function fixup callback. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
* | ARMv8: LS1043A: Enable LS1043A default PSCI supportmacro.wave.z@gmail.com2016-12-15-0/+9
| | | | | | | | | | | | | | | | | | | | A most basic PSCI implementation with only one psci_version is added for LS1043A, this can verify the generic PSCI framework, and more platform specific implementation will be added later. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | fsl/board/ddr: optimize board-specific cpo for erratum A-009942Shengzhou Liu2016-12-15-0/+42
|/ | | | | | | | | | Optimize board-specific cpo for erratum A-009942 on b4860qds, ls1043aqds, ls1043ardb, ls1046aqds, ls1046ardb, ls2080ardb, t102xqds, t102xrdb, t1040qds, t104xrdb, t208xqds, t208xrdb, t4qds, t4rdb boards. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit v1.1 at 2024-11-08 14:49:43 +0000