summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
...
* | board: ti: dra72: Introduce optimization for rgmii timing for rev CNishanth Menon2016-12-04-25/+50
| | | | | | | | | | | | | | | | | | | | | | Rev C version of EVM does require IODelay to be configured for RGMII pins in MANUAL_1 configuration. Update the same based on PG2.0 initial simulation values. Data based on PCT_DRA72x_SR2.0_SR1.0_v1.3.0.7 Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | board: ti: dra71x-evm: Add mux settingsLokesh Vutla2016-12-04-1/+206
| | | | | | | | | | | | | | | | Add mux and iodelay settings for dra71x-evm. Data generated using PCT_DRA71x_SR2.0_v1.0.0.0 version (June 2016). Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | board: ti: dra71x-evm: Add epprom supportLokesh Vutla2016-12-04-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The dra71x-evm is a board based on TI's DRA718 processor targeting BOM-optimized entry infotainment systems such as display audio and is a software compatible derivative of the highly successful DRA74 and DRA72 processor families. More information can be found here[1]. Add epprom detection for dra71-evm. [1] http://www.ti.com/product/dra718 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM: OMAP4+: Add support for dynamically selecting OPPsLokesh Vutla2016-12-04-40/+143
| | | | | | | | | | | | | | | | | | | | | | It can be expected that different paper spins of a SoC can have different definitions for OPP and can have their own constraints on the boot up OPP for each voltage rail. In order to have this flexibility, add support for dynamically selecting the OPP voltage based on the board to handle any such exceptions. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | board: ti: am57xx: add FIT image TEE processingAndrew F. Davis2016-12-03-0/+7
| | | | | | | | | | | | | | | | Populate the corresponding TEE image processing call to be performed during FIT loadable processing. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | board: ti: dra7xx: add FIT image TEE processingAndrew F. Davis2016-12-03-0/+7
| | | | | | | | | | | | | | | | | | Populate the corresponding TEE image processing call to be performed during FIT loadable processing. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | davinci: omapl138_lcdk: add NAND SPL boot supportFabien Parent2016-12-03-28/+0
| | | | | | | | | | | | | | | | | | | | NAND SPL boot was missing. Add it. The README specific to omapl138-lcdk is also removed because its content does not apply anymore, i.e. the generated AIS image can be flashed directly to the NAND without using any external tool to create and bootable AIS image. Signed-off-by: Fabien Parent <fparent@baylibre.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | davinci: da850evm: fix empty boot method list in the SPLFabien Parent2016-12-03-0/+3
| | | | | | | | | | | | | | | | | | | | The list of available boot method is not part of the binary which prevent the SPL from booting u-boot or Linux. Add the missing .u_boot_list* sections to the binary to fix it. Signed-off-by: Fabien Parent <fparent@baylibre.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM: AMx3xx: Make FIT boot as default boot on HS devicesLokesh Vutla2016-12-03-0/+14
| | | | | | | | | | | | | | | | Verification has to be done before booting any images on HS devices. So default the boot to FIT on HS devices. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM: AM57xx: Make FIT boot as default boot on HS devicesLokesh Vutla2016-12-03-0/+8
| | | | | | | | | | | | | | | | Verification has to be done before booting any images on HS devices. So default the boot to FIT on HS devices. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM: DRA7: Make FIT boot as default boot on HS devicesLokesh Vutla2016-12-03-0/+7
| | | | | | | | | | | | | | | | Verification has to be done before booting any images on HS devices. So default the boot to FIT on HS devices. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | sh: add common dram_init() function for all boardsVladimir Zapolskiy2016-12-02-229/+0
| | | | | | | | | | | | | | | | | | | | | | Generic board support assumes a different method of specifying DRAM size on board, also it can be shared among all boards, notably only sh7763rdp board has a custom legacy dram_init(), however the difference is only in printing some additional information, this feature can be removed. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | sh: place board lowlevel_init code in the beginning of .textVladimir Zapolskiy2016-12-02-18/+18
| | | | | | | | | | | | | | | | | | Reference lowlevel_init of all supported SH2A/SH3/SH4/SH4A boards from a shared linker script, the lowlevel_init function will be called by a relative address. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | sh4: use single u-boot linker script for all boardsVladimir Zapolskiy2016-12-02-250/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Three supported SH4/SH4A boards with the bootloader image stored on SPI flash have own flavour of a linker script, in turn they are equal among each other. The only difference is that the text from lowlevel_init.o is placed right after start.o, which makes sense. Note that .bss section is not marked as NOLOAD, because for about 10 years this is a default option of a GNU linker, either the attribute is found or not the resulting image file is the same. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | ARM64: zynqmp: Use DTS name for different psu_init_gpl* files in SPLMichal Simek2016-12-02-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_SYS_CONFIG_NAME is not proper config option for different low level init files because different board revisions requires different psu_init_gpl* files. Also at the end of moving drivers to DM all board specific configuration files should be removed. The same changes was done for Zynq. "ARM: zynq: Simplify zynq configuration" (sha1: ad5b5801264e573bfbf17a20b04c546985c5bfc1) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-11-30-92/+1558
|\ \ | |/ |/|
| * mx6sx: Add initial support for Samtec VIN|ING 2000 boardChristoph Fritz2016-11-30-0/+673
| | | | | | | | | | | | | | | | This patch adds initial support for Samtec VIN|ING 2000 board. Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Marek Vasut <marex@denx.de>
| * imx7: SPI: add suport for SPI flash in mikroBUS slotAngus Ainslie2016-11-29-0/+24
| | | | | | | | | | | | | | | | | | | | Enable the escpi3 nets attached to the mikroBUS slot on the i.MX7 Sabre evalution board. Also enble the SPI flash commands to work with the "flash click" board. This is V2 of this patch with changes recommended by the maintainer CC: Jagan Teki <jteki@openedev.com>
| * mx6sx: Add initial support for UDOO Neo BoardBreno Lima2016-11-29-0/+466
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UDOO Neo Board is a development board from Seco that has three models: - UDOO Neo Basic - UDOO Neo Basic Kick Starter - UDOO Neo Extended - UDOO Neo Full All versions are based on the i.MX6 SoloX processor. For more details about the UDOO Neo board, please refer to: http://www.udoo.org/udoo-neo/ This work is based on a previous commit of Francesco Montefoschi <francesco.monte@gmail.com>: https://github.com/fmntf/u-boot/commit/877b71184a5105e708024f232d36aed574961844 Only tested on the UDOO Neo Full board. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * ARM: ts4600: add basic board supportSebastien Bourdelin2016-11-29-0/+270
| | | | | | | | | | | | | | | | This commit adds basic support including: MMC, Serial console Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * board: ge: bx50v3: add the PMIC configuration supportKen Lin2016-11-29-0/+54
| | | | | | | | | | | | | | | | Change the PMIC bulk configuration from auto mode to sync mode to avoid voltage dropout issue seen in auto mode. Signed-off-by: Ken Lin <ken.lin@advantech.com.tw> Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
| * mx6: ddr: pass mx6_ddr_sysinfo to calibration routinesEric Nelson2016-11-29-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DDR calibration routines have scattered support for bus widths other than 64-bits: -- The mmdc_do_write_level_calibration() routine assumes the presence of PHY1, and -- The mmdc_do_dqs_calibration() routine tries to determine whether one or two DDR PHYs are active by reading MDCTL. Since a caller of these routines must have a valid struct mx6_ddr_sysinfo for use in calling mx6_dram_cfg(), and the bus width is available in the "dsize" field, use this structure to inform the calibration routines which PHYs are active. This allows the use of the DDR calibration routines on CPU variants like i.MX6SL that only have a single MMDC port. Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Marek Vasut <marex@denx.de>
| * arm: imx: wandboard: fix compile error if CONFIG_VIDEO is deactivatedSven Ebenfeld2016-11-29-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | When I tried to deactivate VIDEO support for the Wandboard, it still tried to initialize the Framebuffer and so on. That is the reason for the added ifdefs. CONFIG_VIDEO is enabled in the configuration as default and therefore nothing changes for the default user. The structs mx6dl_i2c2_pad_info and mx6q_i2c2_pad_info are only available when CONFIG_IPUV3 are set and should not be tried to access, when that define is not defined. Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
| * tbs2910: Make Ethernet functional againSoeren Moch2016-11-29-0/+33
| | | | | | | | | | | | | | | | Configure the PHY to output a 125MHz clk from CLK_25M and set tx clock delay. This patch is similar to commit 4b6035da482cccda06aeb419634f99937c9fc783 ("mx6sabresd: Make Ethernet functional again"). Signed-off-by: Soeren Moch <smoch@web.de>
| * Merge branch 'master' of git://git.denx.de/u-bootStefano Babic2016-11-29-154/+2640
| |\ | | | | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
| * | mx35: add GPIO setup on flea3 boardStefano Babic2016-11-16-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware revision "e" of the board introduces a GPIO to reduce power consumption in stand-by mode. This must be enable (active low) at the startup for normal behaviour. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Heiko Schocher <hs@denx.de>
| * | mx35: factorize SDRAM setup in flea3Stefano Babic2016-11-16-90/+3
| | | | | | | | | | | | | | | | | | | | | | | | Drop local function to setup SDRAM controller and use the common one for i.MX35. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Heiko Schocher <hs@denx.de>
| * | mx35: add DT support to flea3 boardHeiko Schocher2016-11-16-0/+24
| | | | | | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* | | Merge git://git.denx.de/u-boot-mpc85xxTom Rini2016-11-29-101/+113
|\ \ \
| * | | powerpc: MPC8641HPCN: Remove macro CONFIG_MPC8641HPCNYork Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Use TARGET_MPC8641HPCN from Kconfig instead. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: MPC8610HPCD: Remove macro CONFIG_MPC8610HPCDYork Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Use TARGET_MPC8610HPCD from Kconfig instead. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T4240RDB: Remove macro CONFIG_T4240RDBYork Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Use CONFIG_TARGET_T4240RDB instead. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T4160RDB: Separate from T4240RDB in KconfigYork Sun2016-11-23-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | Use TARGET_T4160RDB to simplify Kconfig options. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T4240QDS: Remove macro CONFIG_T4240QDSYork Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Use CONFIG_TARGET_T4240QDS instead. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T4160QDS: Separate from T4240QDS in KconfigYork Sun2016-11-23-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | Use TARGET_T4160QDS to simplify Kconfig options. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T2080RDB: Rename from T208XRDB in KconfigYork Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | T208XRDB only has one target T2080RDB. Use TARGET_T2080RDB in Kconfig and clean up existing macros. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T208XQDS: Split as T2080QDS and T2081QDSYork Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Use two separated targets in Kconfig to simplify configurations. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T104xRDB: Remove macro CONFIG_T104xRDB and T104xD4RDBYork Sun2016-11-23-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_T104xRDB is defined in T104xRDB.h, so it is always enabled for all T1040RDB, T1040D4RDB, T1042RDB, T1042D4RDB, T1042RDB_PI. CONFIG_T104XD4RDB is defined for all T1040D4RDB, T1042D4RDB. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T1042RDB: Remove macro CONFIG_T1042RDBYork Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Use TARGET_T1042RDB instead. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T1042D4RDB: Separate from T1042RDB in KconfigYork Sun2016-11-23-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Use TARGET_T1042D4RDB in Kconfig to simplify config options. Remove macro CONFIG_T1042D4RDB. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T1042RDB_PI: Split from T1042RDB in KconfigYork Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Use separated TARGET_T1042RDB_PI to simplify config options. Remove macro CONFIG_T1042RDB_PI. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T1040RDB: Remove macro CONFIG_T1040RDBYork Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Use CONFIG_TARGET_T1040RDB instead. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T1040D4RDB: Separate from T1040RDB in KconfigYork Sun2016-11-23-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Use TARGET_T1040D4RDB in Kconfig to simplify config macros. Replace CONFIG_T1040D4RDB with TARGET_T1040D4RDB and clean up existing macros. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T1040: Remove macro CONFIG_PPC_T1040York Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Replace CONFIG_PPC_T1040 with ARCH_T1040 in Kconfig and clean up existing macros. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T104XRDB: Split to T1040RDB and T1042RDB in KconfigYork Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Split ARCH_T104XRDB as ARCH_T1040RDB and ARCH_T1042RDB in Kconfig to simplify config options. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T1024: Remove macro CONFIG_PPC_T1024York Sun2016-11-23-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Replace CONFIG_PPC_T1024 with ARCH_T1024 in Kconfig and clean up existing macros. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T1024QDS: Rename Kconfig option to match the nameYork Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Rename TARGET_T102XQDS to TARGET_T1024QDS to match the name. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: T102xRDB: Split as T1023RDB and T1024RDBYork Sun2016-11-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The defconfig files are separated. Splitting targets in Kconfig simplifies config options. Signed-off-by: York Sun <york.sun@nxp.com>
| * | | powerpc: B4420: Remove macro CONFIG_PPC_B4420York Sun2016-11-23-6/+6
| | | | | | | | | | | | | | | | | | | | Replace CONFIG_PPC_B4420 with ARCH_B4420 in Kconfig and clean up existing macros.
| * | | powerpc: B4860QDS: Remove macro CONFIG_B4860QDSYork Sun2016-11-23-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | Use CONFIG_TARGET_B4860QDS instead. Signed-off-by: York Sun <york.sun@nxp.com>
generated by cgit v1.1 at 2024-10-15 19:28:45 +0000