summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
* fsl: rename 'dma' to 'brdcfg1' in the ngPIXIS structureTimur Tabi2010-05-30-1/+1
| | | | | | | | | | The ngPIXIS is a board-specific FPGA, but the definition of the registers is mostly consistent. On boards where it matter, register 9 is called 'brdcfg1' instead of 'dma', so rename the variable in the ngpixis_t definition. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* nios: remove nios-32 archThomas Chou2010-05-28-1987/+0
| | | | | | The nios-32 arch is obsolete and broken. So it is removed. Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
* nios2: add gpio support to nios2-generic boardThomas Chou2010-05-28-0/+56
| | | | | | | | | | | This patch adds gpio support of Altera PIO component to the nios2-generic board. Though it drives only gpio_led at the moment, it supports bidirectional port to control bit-banging I2C, NAND flash busy status or button switches, etc. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Tested-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Scott McNutt <smcnutt@psyent.com>
* Convert Makefiles from COBJS-${} to COBJS-$()Kumar Gala2010-05-26-12/+12
| | | | | | Match style we use almost everywhere else Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* bugfix: Guruplug: Use standard miiphyMahavir Jain2010-05-21-8/+1
| | | | | | | | | | | call to reset PHY chip. Current PHY Software Reset operation in guruplug does not poll reset bit in control register to go to 0(auto clearing) for making sure reset was successful.This patch uses standard miiphy call miiphy_reset to make sure proper PHY reset operation. Signed-off-by: Mahavir Jain <mjain@marvell.com>
* Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk2010-05-21-2/+164
|\
| * Add SPI support to mx51evk boardStefano Babic2010-05-05-0/+139
| | | | | | | | | | | | | | The patch adds SPI devices to the mx51evk board. The MC13892 chip (PMIC) is supported. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * MX31: Add support for PMIC to the QONG moduleStefano Babic2010-05-05-0/+20
| | | | | | | | | | | | | | Add support for the PMIC (MC13783) controller and enables charging of the RTC battery. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * MX51evk: Removed warningsStefano Babic2010-05-05-2/+2
| | | | | | | | | | | | | | Changes reflect modifications in the fsl_esdhc driver (the clk_enable field war removed in the configuration structure). Signed-off-by: Stefano Babic <sbabic@denx.de>
| * tx25: fix crash while booting LinuxAnatolij Gustschin2010-05-05-0/+3
| | | | | | | | | | | | | | | | | | | | Currently booting Linux on TX25 board doesn't work since there is no correct mach-id and boot parameters setup for tx25 board. Fix it now. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: John Rigby <jcrigby@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
* | fsl_diu_fb.c: fix build warningsWolfgang Denk2010-05-17-9/+9
| | | | | | | | | | | | | | | | | | | | | | Commit 15351855 "fsl-diu: Using I/O accessor to CCSR space" caused a number of "passing argument 2 of 'out_be32' makes integer from pointer without a cast" warnings; fix these. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Dave Liu <daveliu@freescale.com> Cc: Jerry Huang <Chang-Ming.Huang@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk2010-05-17-1/+1
|\ \
| * | Removal of checkboard from spl bootstrap build for SIMPC8313Ron Madrid2010-05-17-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch removes the checkboard function from the build of the 4k bootstrap section for the SIMPC8313 as it is not needed in the spl build. This will allow > 100 bytes of extra room for other uses. Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk2010-05-17-1/+1
|\ \ \
| * | | ppc4xx: Fix building PLU405 boardMatthias Fuchs2010-05-17-1/+1
| |/ / | | | | | | | | | | | | | | | | | | | | | Due to some overlapping sections it's time to update TEXT_BASE for this board. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
* | | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2010-05-17-50/+57
|\ \ \ | |/ / |/| |
| * | 85xx/fsl-sata: Use is_serdes_configured() to determine if SATA is enabledKumar Gala2010-05-12-11/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the MPC85xx platform if we have SATA its connected on SERDES. Determing if SATA is enabled via sata_initialize should not be board specific and thus we move it out of the MPC8536DS board code. Additionally, now that we have is_serdes_configured() we can determine if the given SATA port is enabled and error out if its not in the driver. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | 85xx/mpc8536ds: Use is_serdes_configured() to determine of PCIe enabledKumar Gala2010-05-12-12/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The new is_serdes_configured covers a broader range of devices than the PCI specific code. Use it instead as we convert away from the is_fsl_pci_cfg() code. Additionally move to setting LAWs for PCI based on if its configured. Also updated PCI FDT fixup code to remove PCI controllers from dtb if they are configured. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | fsl-diu: Using I/O accessor to CCSR spaceJerry Huang2010-05-12-27/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Using PPC I/O accessor to DIU I/O space instead of directly read/write. It will prevent the dozen of compiler order issue and PPC hardware order issue for accessing I/O space. Using the toolchain(tc-fsl-x86lnx-e500-dp-4.3.74-2.i386.rpm) can show up the order issue of DIU driver. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | MVBLM7, MVSMR: fix Makefile (cleanup bootscript.img)Wolfgang Denk2010-05-15-4/+4
|/ / | | | | | | | | | | | | | | | | Fix MVBLM7 and MVSMR Makefiles for correct out-of-tree building (create "bootscript.img" in build directory instead of source directory) and cleanup (remove "bootscript.img" when cleaning up). Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk2010-05-09-0/+36
|\ \
| * | mpc83xx/mvBLM7: add usb commands and cleanup.Andre Schwarz2010-05-07-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add USB commands. Rename autoscript to bootscript. Add automatic bootscript image generation to makefile. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | mpc83xx: Add UPMA configuration to SIMPC8313Ron Madrid2010-05-07-0/+35
| | | | | | | | | | | | | | | | | | | | | Added UPM array table, upmconfig, and Local Bus configuration support for SIMPC8313 Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | | serial: punt unused serial_addr()Mike Frysinger2010-05-07-4/+0
|/ / | | | | | | | | | | | | Only one file apparently defines this function, and it merely stubs it out. So if no one is defining/calling it, punt it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | 74xx_7xx: CPCI750: Add ECC support on esd CPCI-CPU/750 boardReinhard Arlt2010-05-06-7/+156
| | | | | | | | | | | | | | | | | | | | Add ECC support for DDR RAM for MV64360 on esd CPCI-CPU/750 board. This patch also adds the "pldver" command to display the CPLD revision. Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
* | eNET: Implement eNET WatchdogGraeme Russ2010-05-06-0/+46
| | | | | | | | Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* | eNET: Add PC/AT compatibility setup functionGraeme Russ2010-05-06-0/+38
| | | | | | | | | | | | | | | | The eNET uses the sc520 software timers rather than the PC/AT clones Set all interrupts and timers up to be PC/AT compatible Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* | eNET: Add support for onboard RTL8100B (RTL8139) chipsGraeme Russ2010-05-06-0/+7
| | | | | | | | Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* | sc520: Board Specific PCI InitGraeme Russ2010-05-06-0/+33
| | | | | | | | Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* | x86: Use CONFIG_SERIAL_MULTIGraeme Russ2010-05-06-1/+2
| | | | | | | | Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* | x86: Add RAM bootstrap functionalityGraeme Russ2010-05-06-6/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a parameter to the 32-bit entry to indicate if entry is from Real Mode or not. If entry is from Real Mode, execute the destructive 'sizer' routine to determine memory size as we are booting cold and running in Flash. If not entering from Real Mode, we are executing a U-Boot image from RAM and therefore the memory size is already known (and running 'sizer' will destroy the running image) There are now two 32-bit entry points. The first is the 'in RAM' entry point which exists at the start of the U-Boot binary image. As such, you can load u-boot.bin in RAM and jump directly to the load address without needing to calculate any offsets. The second entry point is used by the real-to-protected mode switch This patch also changes TEXT_BASE to 0x6000000 (in RAM). You can load the resulting image at 0x6000000 and simple go 0x6000000 from the u-boot prompt Hopefully a later patch will completely elliminate any dependency on TEXT_BASE like a relocatable linux kernel (perfect world) Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* | x86: Fix MMCR AccessGraeme Russ2010-05-06-43/+43
|/ | | | | | Change sc520 MMCR Access to use memory accessor functions Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* mvsmr: fix link errorAnatolij Gustschin2010-05-04-5/+5
| | | | | | | | | | | MVSMR board support doesn't link since recent rework of U-Boot directory structure. Fix it now. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Andre Schwarz <andre.schwarz@matrix-vision.de> Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Fixed merge conflict Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2010-05-04-301/+842
|\
| * pm9263 converted to at91 soc accessAsen Dimov2010-04-30-101/+109
| | | | | | | | Signed-off-by: Asen Dimov <dimov@ronetix.at>
| * MX31: Removed erroneous board name from QONGStefano Babic2010-04-30-1/+1
| | | | | | | | | | | | | | QONG is a module that can be installed on several boards, not only on the QONG-EVB manufactured by Dave srl. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * MX31: Support 128MB RAM on QONG moduleStefano Babic2010-04-30-33/+97
| | | | | | | | | | | | | | | | | | The QONG module can be downsized and delivered with 128MB instead of 256MB. The patch adds run time support for the two different memory configurations. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * MX31: Add support for NAND to QONG boardStefano Babic2010-04-30-23/+74
| | | | | | | | | | | | | | | | The NAND device is connected to the FPGA of the QONG board and not to the NFC controller. For this reason, the FPGA must be set and initialized before accessing to the NAND itself. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * mx51evk: correct list of possible BOOT_FROM valuesStefano Babic2010-04-30-1/+1
| | | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
| * Marvell GuruPlug Board SupportSiddarth Gore2010-04-30-0/+446
| | | | | | | | | | | | | | | | | | | | | | | | | | | | GuruPlug Standard: 1 Gb Ethernet, 2 USB 2.0 GuruPlug Plus: 2 Gb Ethernet, 2 USB 2.0, 1 eSATA, 1 uSD slot References: http://www.globalscaletechnologies.com/t-guruplugdetails.aspx http://plugcomputer.org This patch is for GuruPlug Plus, but it supports Standard version as well. Signed-off-by: Siddarth Gore <gores@marvell.com>
| * MX51EVK: Remove CPLD related codeFabio Estevam2010-04-30-68/+0
| | | | | | | | | | | | There is no CPLD on MX51EVK board, so remove CPLD related function. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * arm, i.mx27: add support for magnesium board from projectiondesignHeiko Schocher2010-04-30-1/+17
| | | | | | | | | | | | | | | | | | | | | | This patch adds support for the magnesium board from projectiondesign. This board uses i.MX27 SoC and has 8MB NOR flash, 128MB NAND flash, FEC ethernet controller integrated into i.MX27. As this port is based on the imx27lite port, common config options are collected in include/configs/imx27lite-common.h Signed-off-by: Heiko Schocher <hs@denx.de>
| * pm9261 converted to at91 soc accessAsen Dimov2010-04-30-73/+97
| | | | | | | | Signed-off-by: Asen Dimov <dimov@ronetix.at>
* | ppc4xx: Add support for ICON board (PPC440SPe)Stefan Roese2010-04-29-0/+549
| | | | | | | | | | | | | | | | | | | | This patch adds support for the Mosaix Technologies, Inc. ICON board, based on the AppliedMicro (AMCC) PPC440SPe. It's equipped with an SODIMM (512MB standard) and 64MByte of NOR FLASH. Support for the onboard SM502 will be added later. Signed-off-by: Stefan Roese <sr@denx.de>
* | Fix typos in Korat board console outputLarry Johnson2010-04-29-3/+3
|/ | | | | Signed-off-by: Larry Johnson <lrj@acm.org> Signed-off-by: Stefan Roese <sr@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxxWolfgang Denk2010-04-27-4/+750
|\
| * mpc5121: add support for PDM360NG boardAnatolij Gustschin2010-04-24-4/+750
| | | | | | | | | | | | | | | | PDM360NG is a MPC5121E based board by ifm ecomatic gmbh. Signed-off-by: Michael Weiss <michael.weiss@ifm.com> Signed-off-by: Detlev Zundel <dzu@denx.de> Signed-off-by: Anatolij Gustschin <agust@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2010-04-27-3/+7
|\ \
| * | ppc: Split MPC83xx SERDES code from MPC85xx/MPC86xx/QorIQKumar Gala2010-04-26-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | The MPC83xx SERDES control is different from the other FSL PPC chips. For now lets split it out so we can standardize on interfaces for determining of a device on SERDES is configured. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Kim Phillips <kim.phillips@freescale.com>
| * | ppc/85xx: Fixup PCI nodes for P1_P2_RDBKumar Gala2010-04-26-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | While we had ft_pci_board_setup it wasn't being called by ft_board_setup. Fix that so we actually update the device tree PCI nodes on P1_P2_RDB boards. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit v1.1 at 2024-11-28 17:11:31 +0000