summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
* arm: bcmcygnus: Enable Ethernet supportJiandong Zheng2015-08-12-0/+11
| | | | | | | | Enable BCM SF2 ethernet and PHY for BCM Cygnus SoC Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com> Signed-off-by: Steve Rae <srae@broadcom.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* arm, at91: support for sam9260 based smartweb boardHeiko Schocher2015-08-12-0/+258
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | add support for the at91sam9260 based board smartweb from siemens. SPL is used without serial support, as this SoC has only 4k sram for running SPL. Here a U-Boot bootlog: RomBOOT > U-Boot 2015.07-rc2-00109-g4ae828c (Jun 15 2015 - 09:31:16 +0200) CPU: AT91SAM9260 Crystal frequency: 18.432 MHz CPU clock : 198.656 MHz Master clock : 99.328 MHz Watchdog enabled DRAM: 64 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: macb0 Hit any key to stop autoboot: 0 U-Boot> Signed-off-by: Heiko Schocher <hs@denx.de>
* ARM: highbank: remove DRAM bank setupRob Herring2015-08-12-6/+0
| | | | | | | | | | | On the highbank platform the SoC's management controller firmware will probe the DRAM modules and populates the initial device tree with the correct values. Therefore the memory sizes in the DT are already correct, so remove U-Boot's DRAM bank setup so the memory node is not "fixed up" by u-boot. Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Andre Przywara <osp@andrep.de>
* fsl: common: pfuze: no use original pfuze code if DM_PMICPeng Fan2015-08-12-0/+2
| | | | | | | | | | | | If enable DM PMIC and REGULATOR, we should not use original power framework. So need to comment out the pfuze code for original power framework, when CONFIG_DM_PMIC_PFUZE100 defined. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
* Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini2015-08-08-0/+34
|\
| * sunxi: display: Add composite video out supportHans de Goede2015-08-08-0/+7
| | | | | | | | | | | | | | | | | | | | Add composite video out support. This only gets enabled on the Mele M3 for now, since that is were it was tested. It will be enabled on more boards after testing. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * sunxi: nand: Add pinmux and clock settings for NAND supportKarol Gugala2015-08-08-0/+27
| | | | | | | | | | | | | | | | | | | | To enable NAND flash in sunxi SPL, pins 0-6, 8-22 and 24 on port C are configured. Signed-off-by: Karol Gugala <kgugala@antmicro.com> Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | ddr: altera: sequencer: add RW_MGR_MEM_NUMBER_OF_RANKSDinh Nguyen2015-08-08-0/+1
| | | | | | | | | | | | | | | | | | Fix build error for socfpga_cyclone5_defconfig: board/altera/socfpga/wrap_sdram_config.c:245:26: error: ‘RW_MGR_MEM_NUMBER_OF_RANKS’ undeclared here (not in a function) make[2]: *** [spl/board/altera/socfpga/wrap_sdram_config.o] Error 1 Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
* | ddr: altera: sequencer: Wrap misc remaining macrosMarek Vasut2015-08-08-0/+21
| | | | | | | | | | | | | | | | | | | | | | Introduce structure socfpga_sdram_misc_config to wrap the remaining misc configuration values in board file. Again, introduce a function, socfpga_get_sdram_misc_config(), which returns this the structure. This is almost the final step toward wrapping the nasty QTS generated macros in board files and reducing the pollution of the namespace. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
* | ddr: altera: sequencer: Wrap IO_* macrosMarek Vasut2015-08-08-0/+23
| | | | | | | | | | | | | | | | | | | | | | Introduce structure socfpga_sdram_io_config to wrap the IO configuration values in board file. Introduce socfpga_get_sdram_io_config() function, which returns this the structure. This is another step toward wrapping the nasty QTS generated macros in board files and reducing the pollution of the namespace. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
* | ddr: altera: sequencer: Wrap RW_MGR_* macrosMarek Vasut2015-08-08-0/+72
| | | | | | | | | | | | | | | | | | | | | | Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager configuration values in board file. Introduce a complementary function, socfpga_get_sdram_rwmgr_config(), which returns this the structure. This is another step toward wrapping the nasty QTS generated macros in board files and reducing the pollution of the namespace. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
* | ddr: altera: sequencer: Wrap ac_rom_init and inst_rom_initMarek Vasut2015-08-08-0/+15
| | | | | | | | | | | | | | | | | | | | Introduce two wrapper functions, socfpga_get_seq_ac_init() and socfpga_get_seq_inst_init() to avoid direct inclusion of the sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS generated files. This reduces namespace pollution again. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
* | ddr: altera: sequencer: Move qts-generated files to board dirMarek Vasut2015-08-08-0/+601
| | | | | | | | | | | | | | | | Move the files generated by QTS into the board directory, they should not be part of the driver files at all. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
* | ddr: altera: sdram: Introduce socfpga_sdram_get_config()Marek Vasut2015-08-08-1/+187
| | | | | | | | | | | | | | | | | | | | Introduce socfpga_sdram_get_config() function implement in a board file, which returns the socfpga_sdram_config structure. This is the last step in cleaning up the socfpga_mmr_init_full(), but not the last step which allows removing the inclusion of sdram.h from drivers/ddr/altera/sdram.c thus far. Signed-off-by: Marek Vasut <marex@denx.de>
* | arm: socfpga: system: Clean up pinmux_config.cMarek Vasut2015-08-08-8/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement new accessor, sysmgr_get_pinmux_table(), used to obtain pinmux table and it's size from the QTS-generated pinmux_config.c. The target here is again to get rid of poluting global namespace by including the pinmux_config.h into it. Furthermore, the pinmux_config.h declares some CONFIG_HPS_* macros, which are explicitly useless to us in U-Boot. Instead, U-Boot does use DT to detect exactly these configuration options. This patch makes sure that while this QTS-generated file can stay in the tree, these obscure macros do not ooze into the namespace anymore. Signed-off-by: Marek Vasut <marex@denx.de>
* | arm: socfpga: scan: Zap iocsr_scan_chain*_table()Marek Vasut2015-08-08-2/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Introduce accessor iocsr_get_config_table() for retrieving IOCSR config tables. This patch is again trimming down the namespace polution. The IOCSR config tables are used only by scan manager, they are generated by qts and are board specific. Before this patch, the approach to use these tables in scan manager was to define an extern variable to silence the compiler and compile board-specific iocsr_config.c into U-Boot which defined those extern variables. Furthermore, since these are tables and the scan manager needs to know the size of those tables, iocsr_config.h is included build-wide. This patch wraps all this into a single accessor which takes the scan chain ID and returns pointer to the table and it's size. All this is wrapped in wrap_iocsr_config.c board-specific file. The file includes the iocsr_config.c (!) to access the original tables and transitively iocsr_config.h . It is thus no longer necessary to include iocsr_config.h build-wide and the namespace polution is trimmed some more. Signed-off-by: Marek Vasut <marex@denx.de>
* | arm: socfpga: clock: Clean up pll_config.hMarek Vasut2015-08-08-1/+145
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extract the clock configuration horribleness caused by pll_config.h in the following manner. First of all, introduce a few new accessors which return values of various clocks used in clock_manager.c and use them in clock_manager.c . These accessors replace those few macros which came from pll_config.h originally. Also introduce an accessor which returns the struct cm_config default configuration for the clock manager used in SPL. The accessors are implemented in a board-specific wrap_pll_config.c file, whose sole purpose is to include the qts-generated pll_config.h and provide only the necessary values to the clock manager. The purpose of this design is to limit the scope of inclusion for the pll_config.h , which thus far was included build-wide and poluted the namespace. With this change, the inclusion is limited to just the new wrap_pll_config.c file, which in turn provides three simple functions for the clock_manager.c to use. Signed-off-by: Marek Vasut <marex@denx.de>
* | arm: socfpga: Move sdram_config.h to board dirMarek Vasut2015-08-08-0/+100
| | | | | | | | | | | | | | This file is absolutelly positively board specific, so move it into the correct place. Signed-off-by: Marek Vasut <marex@denx.de>
* | arm: socfpga: Move generated files into qts subdirMarek Vasut2015-08-08-1/+8
|/ | | | | | | | | Move all the files generated by Quartus into the qts/ subdir of the board/altera/socfpga dir to make them explicitly separate from the generic U-Boot code. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
* Merge git://git.denx.de/u-boot-dmTom Rini2015-08-06-466/+390
|\
| * exynos: Add support for springSimon Glass2015-08-05-0/+19
| | | | | | | | | | | | | | | | | | | | Spring is the first ARM-based HP Chromebook 11. It is similar to snow and it uses the same Samsung Exynos5250 chip. But has some unusual features. Mainline support for it has lagged snow (both in kernel and U-Boot). Now that the exynos5 code is common we can support spring just by adding a device tree and a few lines of configuration. Signed-off-by: Simon Glass <sjg@chromium.org>
| * exynos: Drop old exynos5250-specific board codeSimon Glass2015-08-05-310/+0
| | | | | | | | | | | | | | Now that most exynos5250 boards can use the generic exynos5 code, switch over to it and remove the old code. Signed-off-by: Simon Glass <sjg@chromium.org>
| * exynos: Drop old exynos5420-specific board codeSimon Glass2015-08-05-147/+0
| | | | | | | | | | | | | | | | Now that exynos5420 boards can use the generic exynos5 code, switch over to it and remove the old code. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
| * exynos: Remove unneeded device tree control #ifdefsSimon Glass2015-08-05-9/+8
| | | | | | | | | | | | | | Since device tree is used for all exynos5 boards, we can remove the #ifdef and reduce confusion. Signed-off-by: Simon Glass <sjg@chromium.org>
| * exynos: Enable new features for exynos5 boardsSimon Glass2015-08-05-1/+1
| | | | | | | | | | | | | | Enable PMICs, regulators and the like so that new drivers will be made available. Signed-off-by: Simon Glass <sjg@chromium.org>
| * exynos: Add common board code for exynos5 boards that use device treeSimon Glass2015-08-05-0/+363
| | | | | | | | | | | | | | | | | | | | Some boards use device tree for almost all board-specific configuration. They therefore do not need their own separate board code, but can all use the same version. Add a common version of the board code. It uses the PMIC, regulator and video bridge uclasses. This will support smdk5250, smdk5420, snow, spring, pit and pi. Signed-off-by: Simon Glass <sjg@chromium.org>
* | ARM: tegra: Add p2371-0000 boardStephen Warren2015-08-06-0/+345
| | | | | | | | | | | | | | | | | | | | | | P2371-0000 is a P2581 or P2530 CPU board married to a P2595 I/O board. The combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB micro-B port, Ethernet via USB3, USB3 host port, SATA, a GPIO expansion header, and an analog audio jack. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | ARM: tegra: Add e2220-1170 boardStephen Warren2015-08-06-0/+354
| | | | | | | | | | | | | | | | | | E2220-1170 is a Tegra210 bringup board with onboard SoC, DRAM, eMMC, SD card slot, HDMI, USB micro-B port, and sockets for various expansion modules. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | ARM: tegra: enable GPU DT node when appropriateAlexandre Courbot2015-08-06-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T124/210 requires some specific configuration (VPR setup) to be performed by the bootloader before the GPU can be used. For this reason, the GPU node in the device tree is disabled by default. This patch enables the node if U-boot has performed VPR configuration. Boards enabled by this patch are T124's Jetson TK1 and Venice2 and T210's P2571. Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <twarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | ARM: tegra: add comment re: autogeneration to pinmux headersStephen Warren2015-08-06-0/+32
| | | | | | | | | | | | | | | | | | | | Add a comment block to the top of each generated Tegra pinmux header file indicating that the file was auto-generated, should not be manually edited, and with a pointer to the tool and command used to generate it. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | T210: P2571: Turn CPU fan onTom Warren2015-08-05-0/+12
| | | | | | | | | | | | | | | | CPU board (E2530) has a fan - turn it on via GPIO to keep the SoC cool. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | T210: P2571: Enable SD-card power via PMIC LDO2Tom Warren2015-08-05-87/+24
|/ | | | | | | | This was done in the 32-bit AVP loader (SPL) but is board-specific so should be moved to the CPU portion. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Stephen Warren <swarren@nvidia.com>
* Merge git://git.denx.de/u-boot-x86Tom Rini2015-08-05-16/+148
|\
| * x86: qemu: Support operation as an EFI payloadSimon Glass2015-08-05-2/+3
| | | | | | | | | | | | | | | | | | Disable a few things which interfere with the EFI init. This allows QEMU to to boot into EFI, load a U-Boot payload then boot to the U-Boot prompt. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
| * x86: baytrail: Support operation as an EFI payloadSimon Glass2015-08-05-2/+3
| | | | | | | | | | | | | | | | | | Disable a few things which interfere with the EFI init. This allows the Minnowboard MAX to boot into EFI, load a U-Boot payload then boot to the U-Boot prompt. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
| * x86: Add EFI board codeBen Stoltz2015-08-05-0/+65
| | | | | | | | | | | | | | | | | | | | Add support for the efi-x86 board, which supports running U-Boot as an EFI 32-bit application. Signed-off-by: Ben Stoltz <stoltz@google.com> Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
| * x86: Add Intel Bayley Bay board supportBin Meng2015-08-05-0/+77
| | | | | | | | | | | | | | | | Intel Bayley Bay board is a BayTrail based board. Add this board with existing baytrail fsp support. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
| * x86: minnowmax: Remove smsc47x superio codesBin Meng2015-08-05-12/+0
| | | | | | | | | | | | | | | | | | On Intel BayTrail SoC, there is a legacy UART (I/O 0x3f8) integrated into the SoC which is enabled by the FSP. Remove the smsc47x superio initialization codes. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* | sunxi: Drop our own copy of the USB_KEYBOARD optionsHans de Goede2015-08-05-7/+0
| | | | | | | | | | | | | | USB_KEYBOARD is now defined in drivers/usb/Kconfig, drop our own duplicate definition. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | sunxi: usb: USB_MUSB_SUNXI move to musb-new KconfigPaul Kocialkowski2015-08-05-9/+0
| | | | | | | | | | | | | | | | | | | | | | Now that the musb-new driver has a Kconfig, we can move Kconfig options to enable controllers to it, so that it's easier in e.g. menuconfig. In addition, this allows declaring support for USB_MUSB_HOST/GADGET in defconfigs instead of the USB_MUSB_SUNXI controller, that will get selected automatically when needed. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* | usb: musb-new: CONFIG_MUSB prefix replacement with CONFIG_USB_MUSBPaul Kocialkowski2015-08-05-18/+18
|/ | | | | | | | | USB-related options are usually prefixed with CONFIG_USB and platform-specific adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for consistency. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* armv7/ls1021a: allow OCRAM access permission as R/W in SPLAlison Wang2015-08-03-171/+184
| | | | | | | | | On LS1021A Rev2.0, OCRAM's security level needs to be changed to non-secure access for SD boot. This patch will allow OCRAM access permission as R/W in SPL. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv7/ls1021atwr: program the regulator for deep sleepchenhui zhao2015-08-03-0/+34
| | | | | | | | Program the external regulator to switch off voltage in deep sleep. Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com> Acked-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv7/ls1021atwr: added deep sleep support in ubootTang Yuantian2015-08-03-3/+65
| | | | | | Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Acked-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2015-08-02-128/+1707
|\
| * imx: mx6ul_14x14_evk add basic board supportPeng Fan2015-08-02-0/+663
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. Add USDHC, I2C, UART, 74LV, USB, QSPI support. 2. Support SPL 3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default supports sd for usdhc2, but can do hardware rework to make usdhc2 support emmc. Boot Log: U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59) reading u-boot.img reading u-boot.img U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800) CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz) CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0 - invalid sensor device Reset cause: POR Board: MX6UL 14x14 EVK I2C: ready DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
| * arm: mx6: cm-fx6: setup hdmi only on hdmi enableNikita Kiryanov2015-08-02-6/+3
| | | | | | | | | | | | | | | | | | Refactor display code to only setup hdmi if do_enable_hdmi() is invoked. Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * arm: mx6: cm-fx6: add support for displaytype env varNikita Kiryanov2015-08-02-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | Add support for selecting display preset using the environment variable "displaytype". This is a preparation for future merging of compulab omap3_display.c display selection code with the cm-fx6 display selection code. The "panel" environment variable is retained for backwards compatibility. Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * arm: mx6: cm-fx6: make it possible to not init displayNikita Kiryanov2015-08-02-24/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement a cm-fx6 specific board_video_skip() to provide the option to not initialize the display. The new function does not init display if the environment variable "panel" is not defined, or if it is set to an unsupported value. Collateral changes: - Don't use the global displays array (it's CONFIG_IMX_VIDEO_SKIP specific). - Don't use detect_hdmi(), since env controlled init makes it unnecessary. Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
| * arm: mx6: cm-fx6: map HDMI to IPU1 DI0 explicitlyNikita Kiryanov2015-08-02-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | U-Boot does not explicitly assign the display to an IPU interface. Instead, it relies on the power-on default of DI0. Since the kernel reassigns HDMI display to DI1, after a warm reset the HDMI display no longer works in U-Boot. Fix this by explicitly assigning HDMI to IPU1 DI0 in U-Boot. Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
generated by cgit v1.1 at 2024-10-30 13:05:01 +0000