summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
* MX35: mx35pdk: wrong board revisionStefano Babic2012-04-16-11/+0
| | | | | | | | | | | | | | | | | | | The board revision is detected accessing to the pmic, that is not available before relocation (I2C). This generates the following error: CPU: Freescale i.MX35 rev 2.0 at 532 MHz. Reset cause: WDOG <reg num> = 7 is invalid. Should be less than 0 Board: MX35 PDK 1.0 The revision number is wrong, as a default value is printed (tested on a mx35pdk Rev. 2.0). Move the output in the board_late_init(), when pmic can be accessed. Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX31: mx31pdk: drop enable_caches from board fileStefano Babic2012-04-16-8/+0
| | | | | | | | | enable_caches() is implemented now in cpu.c for ARM1136. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
* MX53: DDR: Fix ZQHWCTRL field TZQ_CSTroy Kisky2012-04-16-4/+4
| | | | | | | | | Currently, board files are setting this field to 0x01 which the manual says is a reserved value. Change to use the default of 0x02 - 128 cycles. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
* cm-t35: fix Ethernet reset timingIgor Grinberg2012-04-16-5/+6
| | | | | | | | | | | The reset_net_chip() function has wrong timings for the reset pulse. This appeared to work until: 0607e2b (ARMV7: OMAP: Write more than 1 byte at a time in i2c_write) Fix the Ethernet support by introducing right timings. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* BeagleBoard: Remove userbutton command and use gpio command insteadJoel Fernandes2012-04-16-55/+0
| | | | | | | Remove userbutton command and do the detection in board config file using the gpio command Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
* Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk2012-04-09-4/+50
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-net: net/designware: Change timeout loop implementation net/designware: Set ANAR to 0x1e1 net/designware: Program phy registers when auto-negotiation is ON net/designware: Try configuring phy on each dw_eth_init net/designware: Consecutive writes must have delay net/designware: Phy address fix net/designware: Fix the max frame length size net/designware: Fix to restore hw mac address microblaze: Wire up LL_TEMAC driver initialization microblaze: Add faked LL_TEMAC driver configuration microblaze: Enable several ethernet driver compilation net: ll_temac: Add LL TEMAC driver to u-boot Update net subsystem maintainer in doc/git-mailrc net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall back mvgbe: remove warning for unused methods
| * microblaze: Wire up LL_TEMAC driver initializationStephan Linz2012-04-04-0/+36
| | | | | | | | | | | | | | Initialize ll_temac driver. Reported-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Stephan Linz <linz@li-pro.net>
| * microblaze: Add faked LL_TEMAC driver configurationStephan Linz2012-04-04-4/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Expand the specific configuration for the microblaze-generic board in xparameters.h with a faked setup to enable the LL_TEMAC driver. Note: From now the microblaze-generic board is no longer a valid board configuration for a real piece of hardware. Rather than, we use the file config.mk and xparameters.h as a faked board configuration to force the compilation of all potential driver code for Microblaze systems. Signed-off-by: Stephan Linz <linz@li-pro.net>
* | Merge branch 'master' of git://git.denx.de/u-boot-onenandWolfgang Denk2012-04-09-0/+3
|\ \ | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-onenand: onenand: samsung: Enable OneNAND support at Samsung's Exynos4210 onenand: Replace ONENAND_IS_MLC() with ONENAND_HAS_4KB() onenand:samsung OneNAND chip probe functions added for GONI and Exynos4210 onenand:samsung Target dependent OneNAND chip probe function
| * | onenand:samsung OneNAND chip probe functions added for GONI and Exynos4210Lukasz Majewski2012-04-04-0/+3
| |/ | | | | | | | | | | | | | | | | | | | | | | Separate callback for probing OneNAND memory chip. Tested at: Samsung S5PC110 GONI Samsung Exynos4210 (S5PC210 Universal) Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
* | x86: Remove dead code in eNETSimon Glass2012-04-01-5/+0
|/ | | | | | | This avoids a compiler warning about unused variables. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-By: Graeme Russ <graeme.russ@gmail.com>
* pci: get rid of local prototypesLinus Walleij2012-03-30-8/+0
| | | | | | | | two boards were redeclaring pciauto_region_allocate() in their local scope for no obvious reason, the function is in <pci.h> anyway, this is probably just copying artifacts and old cruft. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-stagingWolfgang Denk2012-03-30-0/+10
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'agust@denx.de' of git://git.denx.de/u-boot-staging: lzma: fix printf warnings Remove CONFIG_SYS_EXTBDINFO from snapper9260.h cmd_pxe.c: fix strict-aliasing warnings net: smc91111: use mdelay() doc: Fix some typos in different files disk/part.c: Fix device enumeration through API mkenvimage: Really set the redundant byte when applicable mkenvimage: Don't try to detect comments in the input file mkenvimage: Use mmap() when reading from a regular file mkenvimage: Read/Write from/to stdin/out by default or if the filename is "-" mkenvimage: More error handling mkenvimage: Correct an include and add a missing one mkenvimage: correct and clarify comments and error messages MAKEALL: display SPL size if present ARMV7/Vexpress: add missing get_ticks() and get_tbclk() mkenvimage: fix usage message cmd_fat: add FAT write command fs/fat/fat_write.c: Fix GCC 4.6 warnings FAT write: Fix compile errors
| * ARMV7/Vexpress: add missing get_ticks() and get_tbclk()Liming Wang2012-03-26-0/+10
| | | | | | | | | | | | | | | | | | commit f31a911fe (arm, post: add missing post_time_ms for arm) enables get_ticks and get_tbclk for all arm based boards, arm/vexpress also needs these functions to work. Signed-off-by: Liming Wang <walimisdev@gmail.com> Acked-by: Matt.Waddel@linaro.org
* | Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2012-03-30-1565/+386
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-arm: (146 commits) arm: Use common .lds file where possible arm: add a common .lds link script arm: Remove unneeded setting of LDCSRIPT Define CPUDIR for the .lds link script arm: Remove zipitz2 link script Allow arch directory to contain .lds without requiring Makefile OMAP: Remove omap1610inn-based boards arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix build warnings board/ti/beagle/beagle.c: Fix build warnings sdrc.c: Fix typo in do_sdrc_init() for SPL tegra: i2c: Add I2C driver tegra: fdt: i2c: Add extra I2C bindings for U-Boot tegra: i2c: Select I2C ordering for Seaboard tegra: i2c: Enable I2C on Seaboard tegra: i2c: Select number of controllers for Tegra2 boards tegra: i2c: Initialise I2C on Nvidia boards tegra: Enhance clock support to handle 16-bit clock divisors fdt: Add function to allow aliases to refer to multiple nodes tegra: Rename NV_PA_PMC_BASE to TEGRA2_PMC_BASE tegra: fdt: Enable FDT support for Ventana tegra: fdt: Enable FDT support for Seaboard tegra: usb: Enable USB on Seaboard tegra: usb: Add common USB defines for tegra2 boards tegra: usb: Add USB support to nvidia boards arm: Check for valid FDT after console is up fdt: Avoid early panic() when there is no FDT present tegra: usb: Add support for Tegra USB peripheral tegra: fdt: Add function to return peripheral/clock ID usb: Add support for txfifo threshold tegra: usb: fdt: Add USB definitions for Tegra2 Seaboard tegra: usb: fdt: Add additional device tree definitions for USB ports tegra: fdt: Add clock bindings for Tegra2 Seaboard tegra: fdt: Add clock bindings tegra: fdt: Add additional USB binding fdt: Add tegra-usb bindings file from linux fdt: Add staging area for device tree binding documentation tegra: fdt: Add device tree file for Tegra2 Seaboard from kernel tegra: fdt: Add Tegra2x device tree file from kernel arm: fdt: Add skeleton device tree file from kernel fdt: Add basic support for decoding GPIO definitions fdt: Add functions to access phandles, arrays and bools fdt: Tidy up a few fdtdec problems fdt: Add tests for fdtdec fdt: Add fdtdec_find_aliases() to deal with alias nodes arm: Tegra2: Fix ELDK42 gcc failure with inline asm stack pointer load net: fec_mxc: allow use with cache enabled net: force PKTALIGN to ARCH_DMA_MINALIGN i.MX28: Enable caches by default i.MX28: Make use of the bounce buffer i.MX28: Do data transfers via DMA in MMC driver MMC: Implement generic bounce buffer i.MX28: Add cache support to MXS NAND driver i.MX28: Add cache support into the APBH DMA driver ARM926EJS: Implement cache operations board/vpac270/onenand.c: Fix build errors nhk8815: fix build errors atmel-boards: add missing atmel_mci.h ARM: highbank: setup env from boot source register ARM: highbank: change env config to use nvram ARM: highbank: add reset support ARM: highbank: Add boot counter support ARM: highbank: change TEXT_BASE to 0x8000 ARM: highbank: fix us_to_tick calculation ARM: highbank: add missing get_tbclk ARM: highbank: fix warning for calxedaxgmac_initialize net: calxedaxgmac: fix build due to missing __aligned definition EXYNOS: Add structure for Exynos4 DMC EXYNOS: SMDK5250: Support all 4 UARTs ARM: fix s3c2410 timer code ARM: davinci: fixes for cam_enc_4xx board omap3_spi: receive transmit mode calimain, enbw_cmc: Fix typo in comments Davinci: ea20: use gpio framework to access gpios OMAP3: mt_ventoux: sets its own mtdparts OMAP3: mt_ventoux: updated timing for FPGA twl4030: fix potential power supply handling issues NAND: TI: fix warnings in omap_gpmc.c cam_enc_4xx: Rename 'images' to 'imgs' arm: Add Prep subcommand support to bootm OMAP3: twister: add support to boot Linux from SPL SPL: call cleanup_before_linux() before booting Linux OMAP3: SPL: do not call I2C init if no I2C is set. Add cache functions to SPL for armv7 devkit8000: Implement and activate direct OS boot omap/spl: change output of spl_parse_image_header omap-common/spl: Add linux boot to SPL devkit8000/spl: init GPMC for dm9000 in SPL omap-common: Add NAND SPL linux booting devkit8000: add config for spl command Add cmd_spl command mx53ard: Initialize return code with error mx53: Make PLL2 to be the parent of UART clock configs: imx: Use CONFIG_SF_DEFAULT_CS mx28evk: Provide default values for SPI bus and chip select USB: ehci-mx6: Add proper IO accessors mx6: Read silicon revision from register i.MX28: Drop __naked function from spl_mem_init mxs_spi: Return proper timeout error i.MX28: Make the stabilization delays shorter pmic_i2c: Return error in case of invalid pmic_i2c_tx_num mx6: Remove duplicate definition of ANATOP_BASE_ADDR mx6: Fix reset cause for Power On Reset case i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITE i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG i.MX28: Enable additional DRAM address bits mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use for environment mx31: add "ARM11P power gating" to get_reset_cause mx31pdk: Fix CONFIG_SYS_MEMTEST_END efikamx: Fix CONFIG_SYS_MEMTEST_END mx53smd: Fix CONFIG_SYS_MEMTEST_END mx53evk: Fix CONFIG_SYS_MEMTEST_END mx51evk: Fix CONFIG_SYS_MEMTEST_END i.MX6: mx6qsabrelite: add ext2 support imximage: Remove overwriting of flash_offset IXP: Fix GPIO_INT_ACT_LOW_SET() IXP: Fix NAND build warning on PDNB3 and SCPU IXP: Move PDNB3 and SCPU from Makefile to boards.cfg IXP: Squash warnings in IXP NPE IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST} IXP: Make IXP buildable with arm-linux- toolchains Examples: Properly append LDFLAGS to LD command SPL: Enable YMODEM support on BeagleBone and AM335x EVM SPL: Add YMODEM over UART load support SPL: Add README.omap3 README: document more SPL config options spl.c: Use __noreturn decorator config.mk: Check for -fstack-usage support config.mk: Make cc-option create a file under include/generated ...
| * | arm: Remove zipitz2 link scriptSimon Glass2012-03-30-56/+0
| | | | | | | | | | | | | | | | | | | | | This link script doesn't appear to do anything useful or unique, so drop it, and rely on the CPU one. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | OMAP: Remove omap1610inn-based boardsTom Rini2012-03-29-1327/+0
| | | | | | | | | | | | | | | | | | | | | | | | The CS_AUTOBOOT configurations have been broken for a long time. Kshitij Gupta is no longer at TI making these broken and orphaned boards, so remove. Signed-off-by: Tom Rini <trini@ti.com>
| * | board/ti/beagle/beagle.c: Fix build warningsAnatolij Gustschin2012-03-29-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix: beagle.c:257:13: warning: function declaration isn't a prototype [-Wstrict-prototypes] beagle.c:257:13: warning: function declaration isn't a prototype [-Wstrict-prototypes] Also make beagle_dvi_pup() checkpatch clean, fix: ERROR: open brace '{' following function declarations go on the next line Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Tom Rini <trini@ti.com>
| * | tegra: i2c: Select I2C ordering for SeaboardSimon Glass2012-03-29-0/+18
| | | | | | | | | | | | | | | | | | | | | Select the port ordering for I2C on Seaboard. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | tegra: i2c: Initialise I2C on Nvidia boardsSimon Glass2012-03-29-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | This enables I2C on all Nvidia boards including Seaboard and Harmony. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | tegra: usb: Add USB support to nvidia boardsSimon Glass2012-03-29-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds basic USB support for port 0. The other port is not supported yet. Tegra2 (SeaBoard) # usb start (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 5 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Tegra2 (SeaBoard) # ext2load usb 0:3 10000000 /boot/vmlinuz Loading file "/boot/vmlinuz" from usb device 0:3 (ROOT-A) 2932976 bytes read Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | tegra: usb: fdt: Add USB definitions for Tegra2 SeaboardSimon Glass2012-03-29-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | We set up two USB ports, one of which can be host or device. For some reason the kernel version does enable both ports. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | tegra: fdt: Add clock bindings for Tegra2 SeaboardSimon Glass2012-03-29-0/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the definition of the oscillator clock frequency and the 32KHz clock. The latter is provided by a PMIC on I2C which we don't actually use at present, but we expect this definition to be used in the kernel and want to keep our .dts the same. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | tegra: fdt: Add device tree file for Tegra2 Seaboard from kernelSimon Glass2012-03-29-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | This was taken from commit b48c54e2 at: git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | board/vpac270/onenand.c: Fix build errorsAnatolij Gustschin2012-03-28-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Building for vpac270_ond_256 configuration fails: arch/arm/lib/libarm.o: In function `icache_disable': /home/ag/git/u-boot/arch/arm/lib/cache-cp15.c:156: multiple definition of `icache_disable' board/vpac270/libvpac270.o:/home/ag/git/u-boot/board/vpac270/onenand.c:65: first defined here arch/arm/lib/libarm.o: In function `dcache_disable': /home/ag/git/u-boot/arch/arm/lib/cache-cp15.c:188: multiple definition of `dcache_disable' board/vpac270/libvpac270.o:/home/ag/git/u-boot/board/vpac270/onenand.c:66: first defined here make[1]: *** [/home/ag/git/u-boot/spl/u-boot-spl] Error 1 Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
| * | atmel-boards: add missing atmel_mci.hAndreas Bießmann2012-03-28-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 72fa467988e7944407a634ddc4bc6a2df685c04c moved atmel_mci_init() into include/atmel_mci.h. Some AT91 boards are also using this interface and need to include atmel_mci.h now. This patch fixes MAKEALL complaints like this: ---8<--- Configuring for ethernut5 - Board: ethernut5, Options: AT91SAM9XE ethernut5.c: In function 'board_mmc_init': ethernut5.c:235:2: warning: implicit declaration of function 'atmel_mci_init' [-Wimplicit-function-declaration] --->8--- Signed-off-by: Andreas Bießmann <biessmann@corscience.de> CC: Albert Aribaud <albert.u.boot@aribaud.net> CC: Reinhard Meyer <u-boot@emk-elektronik.de> CC: egnite GmbH <info@egnite.de>
| * | ARM: highbank: setup env from boot source registerRob Herring2012-03-28-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add support to read the boot src register and set bootcmd env from the selected bootcmdX env setting. Based on Linkstation boot choice selection. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
| * | ARM: highbank: add reset supportRob Herring2012-03-28-0/+8
| | | | | | | | | | | | | | | | | | | | | Implement reset for highbank platform. Reset is triggered via a wfi instruction, so enabling armv7 for the compiler is necessary. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
| * | ARM: highbank: Add boot counter supportRob Herring2012-03-28-0/+1
| | | | | | | | | | | | | | | | | | Add boot counter support using an sysreg which is persistent across reset. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
| * | ARM: highbank: fix warning for calxedaxgmac_initializeRob Herring2012-03-28-0/+1
| | | | | | | | | | | | | | | | | | Add include of netdev.h to pick-up declaration of calxedaxgmac_initialize. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
| * | EXYNOS: SMDK5250: Support all 4 UARTsDoug Anderson2012-03-27-2/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This properly configures the mux to enable all UARTs. This also fixes things so that we don't configure balls XUCTSN_1 and XURTSN_1 as UART1 configuration (RTS/CTS), since they aren't connected. Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Chander kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | ARM: davinci: fixes for cam_enc_4xx boardHeiko Schocher2012-03-27-17/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - change CONFIG_ENV_RANGE to contain 2 nand erase blocks, one for bad block reserve. - remove from the envvariable "img_writeramdisk" the ubifsmount command, as it is not needed. - erase the hole mtd partition containing u-boot - save environment variable "dvn_app_vers" and "dvn_boot_vers" only after installing the new image. changes requested from Marek Vasut: - arm, davinci: fix eldk-4.2 warnings for cam_enc_4xx board - get rid of run_command2 usage needed since patch: commit 009dde1955583e306cf904c864068f3acb0db499 Author: Simon Glass <sjg@chromium.org> Date: Tue Feb 14 19:59:20 2012 +0000 Rename run_command2() to run_command() is now in mainline. - add CONFIG_SPL_LIBGENERIC_SUPPORT support - remove CONFIG_CMD_PXE support - fix warning: cam_enc_4xx.c: In function 'menu_handle': cam_enc_4xx.c:609: warning: dereferencing type-punned pointer will break strict-aliasing rules - fix error: arm-linux-ld: u-boot-spl: Not enough room for program headers, try linking with -N Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Tom Rini <tom.rini@gmail.com> Cc: Fletzer Martin <Martin.Fletzer@ait.ac.at> Cc: Wolfgang Denk <wd@denx.de>
| * | calimain, enbw_cmc: Fix typo in commentsChristian Riesch2012-03-27-2/+2
| | | | | | | | | | | | | | | | | | Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
| * | Davinci: ea20: use gpio framework to access gpiosStefano Babic2012-03-27-29/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Drop direct access to SOC's registers and use the function of the GPIO driver for da8xx. [Tom: Remove gpio[68]_base as it's now unused] Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Bastian Ruppert <Bastian.Ruppert@Sewerin.de> CC: dzu@denx.de CC: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
| * | OMAP3: mt_ventoux: updated timing for FPGAStefano Babic2012-03-27-6/+5
| | | | | | | | | | | | | | | | | | | | | Fix chipselect timing for FPGA Signed-off-by: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com>
| * | cam_enc_4xx: Rename 'images' to 'imgs'Tom Rini2012-03-27-24/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To avoid a conflict with common/cmd_bootm.c's 'images' (which is exposed as part of the Linux SPL series), rename the board-specific 'images' to 'imgs'. Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de>
| * | OMAP3: twister: add support to boot Linux from SPLStefano Babic2012-03-27-0/+23
| | | | | | | | | | | | | | | | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> CC: Wolfgang Denk <wd@denx.de> CC: Simon Schwarz <simonschwarzcor@gmail.com>
| * | devkit8000: Implement and activate direct OS bootSimon Schwarz2012-03-27-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Implements spl_start_uboot() for devkit8000 - Add configs to activate direct OS boot from SPL Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
| * | devkit8000/spl: init GPMC for dm9000 in SPLSimon Schwarz2012-03-27-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | Linux crashes if the GPMC isn't configured for the dm9000. Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
| * | mx53ard: Initialize return code with errorFabio Estevam2012-03-27-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | The variable "rc" is the return of board_eth_init() function. Initialize it with an error code, so that this function can return an error when CONFIG_SMC911X is not set. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * | i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAGEric Nelson2012-03-27-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is needed to support Freescale-supplied userspaces. At the moment, both the IPU and VPU libraries provided by Freescale in the "imx-lib" package contain routines which scrape the system revision from /proc/cpuinfo. In the VPU library, this information is used to load the proper firmware, allowing a single binary to be used across various i.MX processors. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
| * | mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use ↵Eric Nelson2012-03-27-4/+4
| | | | | | | | | | | | | | | | | | for environment Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * | IXP: Fix NAND build warning on PDNB3 and SCPUMarek Vasut2012-03-26-13/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | nand.c: In function ‘pdnb3_nand_read_buf’: nand.c:107:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] nand.c: In function ‘pdnb3_nand_dev_ready’: nand.c:124:18: warning: variable ‘val’ set but not used [-Wunused-but-set-variable] Remove the 4-byte-at-time read mode altogether, the most is bogus and will likely cause unaligned accesses. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
| * | IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST}Marek Vasut2012-03-26-13/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | These symbols are no longer defined in Linux-ARM's mach-types files. Replace these with CONFIG_MACH_TYPE instead. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
| * | M28: Support for the old M28 SoM v1.0Marek Vasut2012-03-26-0/+5
| | | | | | | | | | | | | | | | | | | | | This prototype version SoM is unused and not available to public. Support this only for internal debugging purposes. Signed-off-by: Marek Vasut <marex@denx.de>
| * | M28: Fix LCD PINMUXMarek Vasut2012-03-26-9/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The LCD pins configuration was wrong in U-Boot, configure pins properly. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com>
| * | mx6qsabrelite: add and enable USB Host 1 supportWolfgang Grandegger2012-03-26-0/+18
| | | | | | | | | | | | | | | | | | Cc: Stefano Babic <sbabic@denx.de> Cc: Jason Liu <jason.hui@linaro.org> Signed-off-by: Wolfgang Grandegger <wg@denx.de>
| * | PXA: Fix warning in zipitz2Marek Vasut2012-03-26-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | Configuring for zipitz2 board... zipitz2.c: In function ‘board_mmc_init’: zipitz2.c:85:2: warning: implicit declaration of function ‘pxa_mmc_register’ [-Wimplicit-function-declaration] Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
| * | arm: Remove jornada link scriptSimon Glass2012-03-26-58/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | This link script seems old and incompatible with relocation and its own sa1000 start.S file. It isn't used because the CPU's link script was picked up in preference to this. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
| * | zipitz2: use pxa_mmc_gen as MMC driverVasily Khoruzhick2012-03-26-0/+8
| |/ | | | | | | Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>