summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
...
* | | ARM: DRA7: EMIF: Update SDRAM_REF_CTRL register valueLokesh Vutla2015-02-16-2/+4
| |/ |/| | | | | | | | | | | | | | | | | | | The value in SDRAM_REF_CTRL controls the delay time between the initial rising edge of DDR_RESETn to rising edge of DDR_CKE (JEDEC specs this as 500us). In order to achieve this, SDRAM_REF_CTRL should be written with a value corresponding to 500us delay before starting DDR initialization sequence, and configure proper value at the end of sequence. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | Merge git://git.denx.de/u-boot-marvellTom Rini2015-02-16-0/+139
|\ \
| * | lsxl: add a README fileMichael Walle2015-02-16-0/+139
| |/ | | | | | | | | | | | | | | The README describes the recovery method which can be used if the NAS box is not reachable anymore. Addionally, it describes the different boot scripts. Signed-off-by: Michael Walle <michael@walle.cc>
* | Merge git://git.denx.de/u-boot-samsungTom Rini2015-02-13-10/+30
|\ \
| * | odroid: fix g2d sclk rateJoonyoung Shim2015-02-13-2/+2
| | | | | | | | | | | | | | | | | | | | | G2D core should be provided 200MHz clock rate. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | samsung: board: support eMMC reset using DTJoonyoung Shim2015-02-13-8/+28
| |/ | | | | | | | | | | | | | | | | | | | | Some exynos boards require special handling of nRESET_OUT line for eMMC memory to perform complete reboot e.g. Odroid X2/U3/XU3 boards. This will support eMMC reset using DT from reset_misc of samsung common board file. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | Merge git://git.denx.de/u-boot-dmTom Rini2015-02-13-2/+209
|\ \
| * | dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to KconfigSimon Glass2015-02-12-0/+6
| | | | | | | | | | | | | | | Move this option to Kconfig and update all boards. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | dm: omap3: Move driver model CONFIGs to KconfigSimon Glass2015-02-12-0/+55
| | | | | | | | | | | | | | | | | | | | | Remove driver model CONFIGs from the board config headers and use Kconfig instead. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | dm: exynos: Move driver model CONFIGs to KconfigSimon Glass2015-02-12-0/+24
| | | | | | | | | | | | | | | | | | | | | Remove driver model CONFIGs from the board config headers and use Kconfig instead. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | powerpc: ppc4xx: Enable CONFIG_DISPLAY_BOARDINFOStefan Roese2015-02-12-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This also displays the "Board:" line in the bootup text with the generic board support code. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
| * | dm: powerpc: ppc4xx: Move glacier to use driver model for serialSimon Glass2015-02-12-0/+14
| | | | | | | | | | | | | | | | | | | | | Adjust Kconfig to default to driver model for glacier, canyonlands and arches. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | powerpc: ppc4xx: Use CONFIG_OF_CONTROL for canyonlands boardsSimon Glass2015-02-12-2/+8
| | | | | | | | | | | | | | | | | | | | | Enable CONFIG_OF_CONTROL so that U-Boot on these three boards uses a device tree for its configuration. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | powerpc: ppc4xx: Add ramboot config for glacierSimon Glass2015-02-12-0/+80
| | | | | | | | | | | | | | | | | | | | | Add a new ramboot config for glacier so that it is possible to test U-Boot loaded over Ethernet instead of using JTAG. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | powerpc: ppc4xx: Move CANYONLANDS/GLACIER/ARCHES to KconfigSimon Glass2015-02-12-0/+20
| | | | | | | | | | | | | | | | | | Move these options to Kconfig and remove them from the CONFIG files. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | powerpc: ppc4xx: canyonlands: config: Tidy up CONFIGs and config.mkSimon Glass2015-02-12-2/+0
| |/ | | | | | | | | | | | | | | Many CONFIG options have an unnecessary value of 1. CONFIG_440 is set in the various board config files. Also simplify the CONFIG_440 check in config.mk Signed-off-by: Simon Glass <sjg@chromium.org>
* | Merge branch 'rmobile' of git://git.denx.de/u-boot-shTom Rini2015-02-13-0/+1155
|\ \ | |/ |/|
| * ARM: rmobile: silk: Remove initialization of ACTLR.SMPNobuhiro Iwamatsu2015-02-13-12/+0
| | | | | | | | | | | | | | Initialization of ACTLR.SMP is in lowlevel_init. This remove duplicate function. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * arm: rmobile: Add missed header file for Silk boardVladimir Barinov2015-02-13-0/+13
| | | | | | | | | | | | | | | | This file was missed in the commit https://patchwork.ozlabs.org/patch/427801/ Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * arm: rmobile: Add SILK board supportVladimir Barinov2015-02-13-0/+1154
| | | | | | | | | | | | | | | | | | | | | | SILK is an entry level development board based on R-Car E2 SoC (R8A7794) This commit supports the following peripherals: - SCIF, I2C, Ethernet, QSPI, MMC, USB Host Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Reviewed-by: Tom Rini <trini@ti.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-x86Tom Rini2015-02-10-2/+141
|\ \
| * | x86: Add basic Intel Galileo board supportBin Meng2015-02-06-0/+62
| | | | | | | | | | | | | | | | | | | | | | | | | | | New board/intel/galileo board directory with minimum codes, plus board dts, defconfig and configuration files. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
| * | x86: Add support for Intel Minnowboard MaxSimon Glass2015-02-06-0/+78
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a relatively low-cost x86 board in a small form factor. The main peripherals are uSD, USB, HDMI, Ethernet and SATA. It uses an Atom 3800 series CPU. So far only the dual core 2GB variant is supported. This uses the existing FSP support. Binary blobs are required to make this board work. The microcode update is included as a patch (all 3000 lines of it). Change-Id: I0088c47fe87cf08ae635b343d32c332269062156 Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
| * | x86: Rename MMCONF_BASE_ADDRESS and make it common across x86Simon Glass2015-02-05-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | This setting will be used by more than just ivybridge so make it common. Also rename it to PCIE_ECAM_BASE which is a more descriptive name. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini2015-02-10-0/+170
|\ \ \
| * | | ARM: atmel: sama5d4_xplained: enable spl supportBo Shen2015-02-07-0/+85
| | | | | | | | | | | | | | | | Signed-off-by: Bo Shen <voice.shen@atmel.com>
| * | | ARM: atmel: sama5d4ek: enable SPL supportBo Shen2015-02-07-0/+85
| |/ / | | | | | | | | | | | | | | | | | | The sama5d4ek support boot up from NAND flash, SD/MMC card and also the SPI flash. Signed-off-by: Bo Shen <voice.shen@atmel.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini2015-02-10-0/+1
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: include/splash.h Signed-off-by: Tom Rini <trini@ti.com>
| * | | lcd: dt: extract simplefb supportNikita Kiryanov2015-02-10-0/+1
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We now have api functions that can support compiling simplefb code as its own module. Since this code is not part of the display functionality, extract it to its own file. Raspberry Pi is updated to accommodate the changes. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Bo Shen <voice.shen@atmel.com> Tested-by: Josh Wu <josh.wu@atmel.com> Cc: Simon Glass <sjg@chromium.org> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stephen Warren <swarren@wwwdotorg.org>
* | | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2015-02-10-155/+1672
|\ \ \ | |_|/ |/| |
| * | mx53loco: Fix boot hang during reboot stress testFabio Estevam2015-02-10-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently by running the following test: => setenv bootcmd reset => save => reset , we observe a hang after approximately 20-30 minutes of stress reboot test. Investigation of this issue revealed that when a single DDR chip select is used, the hang does not happen. It only happens when the two chip selects are active. MX53 reference manual states at "28.6.2 Memory ZQ calibration sequence": "The controller must keep the memory lines quiet (except for CK) for the ZQ calibration time as defined in the Jedec (512 cycles for ZQCL after reset, 256 for other ZQCL and 64 for ZQCS)." According to the SDE_0 and SDE_1 bit descriptions from register ESDCTL_ESDCTL: "Writing 1 to SDE0 or SDE1 will initiate power up delays as JEDEC defines. Power up delays are a function of the configured memory type (DDR2/DDR3/LPDDR2)" So make sure to activate one chip select at time (CS0 first and then CS1 later), so that the required JEDEC delay is respected for each chip select. With this change applied the board has gone through three days of reboot stress test without any hang. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * | imx: mx6qsabreauto: Change to use common GPMI IO clock functionYe.Li2015-02-10-23/+2
| | | | | | | | | | | | | | | | | | | | | | | | Since a clock function setup_gpmi_io_clk is implemented for GPMI IO clock settings, change to use this common function in GPMI setup. Signed-off-by: Ye.Li <B37916@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * | arm, imx6, aristainetos: board updatesHeiko Schocher2015-01-29-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - use linux display timing settings - change backlight duty cycle 500ns - some defaultenvironment changes - change fit_addr_r to 0x14000000 as needed if MAX_LOCKDEP_SUBCLASSES in linux gets increased. - Environment now at 0xd0000 in nand flash Signed-off-by: Heiko Schocher <hs@denx.de>
| * | common: convert compulab splash load code to common codeNikita Kiryanov2015-01-29-191/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move board/compulab/common/splash.c code to common/splash_source.c to make it available for everybody. This move renames cl_splash_screen_prepare() to splash_source_load(), and the compilation of this code is conditional on CONFIG_SPLASH_SOURCE. splash_source features: * Provide a standardized way for declaring board specific splash screen locations * Provide existing routines for auto loading the splash image from the locations as declared by the board * Introduce the "splashsource" environment variable, which makes it possible to select the splash image source. cm-t35 and cm-fx6 are updated to use the modified version. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Anatolij Gustschin <agust@denx.de> Reviewed-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * | arm: mx6: cm-fx6: add splash screen supportNikita Kiryanov2015-01-29-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for splash screen. The splash screen is loaded from the SPI flash and is displayed on the HDMI display. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> [grinberg@compulab.co.il: minor code and commit message updates] Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il>
| * | compulab: splash: support loading splash from sfNikita Kiryanov2015-01-29-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for loading splash from sf. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> [grinberg@compulab.co.il: staticize the sf global variable] Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il>
| * | compulab: splash: support multiple splash sourcesNikita Kiryanov2015-01-29-11/+85
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Define a generic way for boards to define splash image locations: - introduce struct splash_location - introduce enum splash_storage - update cl_splash_screen_prepare() to take an array of above struct and select the appropriate one based on the splashsource environment variable (if it is not defined- use the first splash location as default). cm-t35 is updated to work with the new interface. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * | compulab: splash: refactor splash.cNikita Kiryanov2015-01-29-19/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move storage device specific code into its own function instead of calling it directly from an otherwise storage device independent function (cl_splash_screen_prepare). This is a preparation for supporting multiple splash locations. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * | compulab: splash: use errno valuesNikita Kiryanov2015-01-29-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | Use errno values to improve return reporting. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * | arm: mx6: cm-fx6: add hdmi console supportNikita Kiryanov2015-01-29-0/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for hdmi console. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * | arm: mx6: cm-fx6: pass 2nd nic mac addr to LinuxNikita Kiryanov2015-01-29-7/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | Obtain 2nd NIC MAC address from baseboard EEPROM and pass it to Linux. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * | compulab: eeprom: allow reading mac address from multiple eepromsNikita Kiryanov2015-01-29-14/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement the option to select the eeprom i2c bus when reading mac address. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Ledvich <ilya@compulab.co.il> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * | arm: mx6: cm-fx6: change dtb node for ethaddrNikita Kiryanov2015-01-29-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When passing eth address to Linux via dtb, the "local-mac-address" property should be set for "/soc/aips-bus@02100000/ethernet@02188000", not "/fec". Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * | ot1200: add basic SPL supportChristian Gmeiner2015-01-22-0/+166
| | | | | | | | | | | | | | | | | | Currently we only support the Micron MT41K128M16JT-125 ddr3 chip. Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
| * | ot1200: enable spi clock directly in ccgr_init(..)Christian Gmeiner2015-01-22-4/+1
| | | | | | | | | | | | Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
| * | ot1200: move ccgr and gpr init to c functionsChristian Gmeiner2015-01-22-14/+28
| | | | | | | | | | | | | | | | | | We need this way for SPL boot. Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
| * | ot1200: make use of imx_ddr_size(..)Christian Gmeiner2015-01-22-1/+2
| | | | | | | | | | | | | | | | | | | | | To support different ddr3 memory sizes we should start using imx_ddr_size(..) instead of the define PHYS_SDRAM_SIZE. Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
| * | mx6: fix warning in platinum boardStefano Babic2015-01-22-0/+1
| | | | | | | | | | | | | | | | | | | | | Fix warning due to missing prototype for writel Signed-off-by: Stefano Babic <sbabic@denx.de> Acked-by: Stefan Roese <sr@denx.de>
| * | imx:mx6sxsabresd board spl supportPeng Fan2015-01-22-0/+169
| | | | | | | | | | | | | | | | | | Add board level spl support for mx6sxsabresd board. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
| * | arm: mx6: Add Barco platinum-picon and platinum-titaniumStefan Roese2015-01-19-0/+1183
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the new Barco platinum platform. It currently includes those two boards: platinum-titanium ----------------- This is the same board as the titanium that is already supported in mainline U-Boot. But its now moved to this new platform to support multiple "flavors" of imx6 boards in one directory. Its also moved to support SPL booting. And with this we use the run-time DDR configuration of this SPL support. The board is equipped with the Micron MT41J128M16JT-125 DDR chips. We now can remove the DDR related registers tuples from the imximage.cfg file. As all this is done in the SPL at run-time. platinum-picon -------------- This board is new and based on the MX6DL with 1GiB DDR using the Micron MT41K256M16HA DDR3 chips. Its also equipped with 2 NAND chips (each 512MiB). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Pieter Ronsijn <pieter.ronsijn@barco.com>
generated by cgit v1.1 at 2024-11-01 08:19:35 +0000