summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
...
* | | | | igep00x0: Remove IGEP0020_NAND BOARD entry from MAINTAINERSLadislav Michl2017-01-14-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boards with NAND and OneNAND are supported by single configuration, thus remove now obsolete IGEP0020_NAND BOARD entry. Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
* | | | | igep00x0: enable CONFIG_FDT_FIXUP_PARTITIONSLadislav Michl2017-01-14-0/+17
|/ / / / | | | | | | | | | | | | | | | | | | | | | | | | SPL partition size depends on sector size and we want kernel to use the same layout, so let U-Boot modify FDT accordingly. Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
* | | | arm: Remove unregister MACH_TYPE_xxx usesTom Rini2017-01-14-19/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Before we can sync with the latest mach-types.h file from the Linux Kernel we need to remove some instances of MACH_TYPE_xxx from our sources. As these values have been removed from the canonical upstream source we should not be using them either, so drop. Cc: Tom Warren <twarren@nvidia.com> Cc: Lucas Stach <dev@lynxeye.de> Cc: Luka Perkov <luka@openwrt.org> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Heiko Schocher <hs@denx.de> Cc: Thomas Weber <weber@corscience.de> Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com> Cc: Matthias Weisser <weisserm@arcor.de> Cc: Suriyan Ramasami <suriyan.r@gmail.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Cc: Bo Shen <voice.shen@atmel.com> Cc: Nick Thompson <nick.thompson@gefanuc.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Erik van Luijk <evanluijk@interact.nl> Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* | | | omap3_logic: Rework MACH_TYPE and fdtfile logicTom Rini2017-01-14-34/+20
|/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MACH_TYPE values for the omap37xx based platforms are no longer officially valid, so we must not set and pass them. In order to not reference them but still be able to set the default fdtfile based on the board detection logic we need to combine the two steps into one. Cc: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Adam Ford <aford173@gmail.com>
* | | rockchip: board: popmetal: de-assert the host rst pin in board initKever Yang2017-01-11-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The PopMetal board have a on board FE1.1 usb 2.0 hub which connect to the usb host port, we need to de-assert its reset pin to enable it. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org> Added rockchip: tag: Signed-off-by: Simon Glass <sjg@chromium.org>
* | | SPL: Adjust more debug prints for ulong entry_pointTom Rini2017-01-11-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | With entry_point now being an unsigned long we need to adapt the last two debug prints to use %lX not %X. Fixes: 11e1479b9e67 ("SPL: make struct spl_image 64-bit safe") Signed-off-by: Tom Rini <trini@konsulko.com>
* | | Merge tag 'xilinx-for-v2017.03' of git://www.denx.de/git/u-boot-microblazeTom Rini2017-01-11-0/+11
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Xilinx changes for v2017.03 - ATF handoff - DT syncups - gem: Use wait_for_bit(), add simple clk support - Simple clk driver for ZynqMP - Other small changes
| * | | ARM: zynq: Setup modeboot variable based on boot modeMichal Simek2017-01-10-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | modeboot variable is used for saving inforation which bootmode is used. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | microblaze: Make the board configuration name user definableSai Pavan Boddu2017-01-10-0/+5
| | |/ | |/| | | | | | | | | | | | | | | | Add a prompt for editing in menuconfig Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | | ARM: sunxi: remove bare default for CONFIG_MMCMasahiro Yamada2017-01-11-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | The bare default entry is wrong. Just remove it since the (real) entry in drivers/mmc/Kconfig has "default ARM || PPC || SANDBOX". Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
* | | mmc: move more driver config options to KconfigMasahiro Yamada2017-01-11-25/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move (and rename) the following CONFIG options to Kconfig: CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI) CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS) CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC) CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS) CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA) CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI) They are the same option names as used in Linux. This commit was created as follows: [1] Rename the options with the following command: find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e ' s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g ' [2] Commit the changes [3] Create entries in driver/mmc/Kconfig. (copied from Linux) [4] Move the options with the following command tools/moveconfig.py -y -r HEAD \ MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI [5] Sort and align drivers/mmc/Makefile for readability Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
* | | mmc: move CONFIG_DWMMC to Kconfig, renaming to CONFIG_MMC_DWMasahiro Yamada2017-01-11-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit was created as follows: [1] Rename the option with the following command: find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g' [2] create the entry for MMC_DW in drivers/mmc/Kconfig (the prompt and help were copied from Linux) [3] run "tools/moveconfig.py -y MMC_DW" [4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry [5] Clean-up doc/README.socfpga by hand Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
* | | Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini2017-01-10-0/+27
|\ \ \ | |/ / |/| |
| * | sunxi: A64: enable SPLAndre Przywara2017-01-04-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that the SPL is ready to be compiled in AArch64 and the DRAM init code is ready, enable SPL support for the A64 SoC and in the Pine64 defconfig. For now we keep the boot0 header in the U-Boot proper, as this allows to still use boot0 as an SPL replacement without hurting the SPL use case. We disable FEL support for now by making its compilation conditional and disabling it for ARM64, as the code isn't ready yet. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
| * | sunxi: provide default DRAM config for sun50i in KconfigAndre Przywara2017-01-04-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To avoid enumerating the very same DRAM values in defconfig files for each and every Allwinner A64 board out there, let's put some sane default values in the Kconfig file. Boards with different needs can override them at any time. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
| * | sunxi: A64: do an RMR switch if started in AArch32 modeAndre Przywara2017-01-04-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Allwinner A64 SoC starts execution in AArch32 mode, and both the boot ROM and Allwinner's boot0 keep running in this mode. So U-Boot gets entered in 32-bit, although we want it to run in AArch64. By using a "magic" instruction, which happens to be an almost-NOP in AArch64 and a branch in AArch32, we differentiate between being entered in 64-bit or 32-bit mode. If in 64-bit mode, we proceed with the branch to reset, but in 32-bit mode we trigger an RMR write to bring the core into AArch64/EL3 and re-enter U-Boot at CONFIG_SYS_TEXT_BASE. This allows a 64-bit U-Boot to be both entered in 32 and 64-bit mode, so we can use the same start code for the SPL and the U-Boot proper. We use the existing custom header (boot0.h) functionality, but restrict the existing boot0 header reservation to the non-SPL build now. A SPL wouldn't need such header anyway. This allows to have both options defined and lets us use one for the SPL and the other for U-Boot proper. Also add arch/arm/mach-sunxi/rmr_switch.S, which contains the original ARM assembly code and instructions how to re-generate the encoded version. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
| * | sunxi: introduce extra config option for boot0 headerAndre Przywara2017-01-04-0/+9
| |/ | | | | | | | | | | | | | | | | | | | | | | The ENABLE_ARM_SOC_BOOT0_HOOK option is a generic option shared with other boards. To allow alternative code to be inserted, we create another, now function specific config symbol on top of it to simplify later additions. No functional change at this time. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
* | mx6ullevk: Add missing MAINTAINERS for mx6ull_14x14_evk_plugin_defconfigJagan Teki2017-01-08-0/+1
| | | | | | | | | | | | | | | | | | | | | | Add 'Peng Fan' as MAINTAINERS of configs/mx6ull_14x14_evk_plugin_defconfig which is missing in below commit "imx: mx6ull_14x14_evk: add plugin defconfig" (sha1: b90ebf49bb8f74afe68f696f59a0e24cc79f2031) Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Jagan Teki <jagan@openedev.com>
* | ddr: fsl: Merge macro CONFIG_NUM_DDR_CONTROLLERS and CONFIG_SYS_NUM_DDR_CTRLSYork Sun2017-01-04-5/+5
| | | | | | | | | | | | | | | | These two macros are used for the same thing, the total number of DDR controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and merge existing usage. Signed-off-by: York Sun <york.sun@nxp.com>
* | powerpc: T2081QDS: Remove macro T2081QDSYork Sun2017-01-04-10/+10
| | | | | | | | | | | | Use TARGET_T2081QDS from Kconfig instead. Signed-off-by: York Sun <york.sun@nxp.com>
* | powerpc: T2080RDB: Remove macro CONFIG_T2080RDBYork Sun2017-01-04-1/+1
| | | | | | | | | | | | Use TARGET_T2080RDB from Kconfig instead. Signed-off-by: York Sun <york.sun@nxp.com>
* | powerpc: T2080QDS: Remove macro T2080QDSYork Sun2017-01-04-12/+12
| | | | | | | | | | | | Use TARGET_T2080QDS from Kconfig instead. Signed-off-by: York Sun <york.sun@nxp.com>
* | powerpc: T1024RDB: Remove macro CONFIG_T1024RDBYork Sun2017-01-04-10/+10
| | | | | | | | | | | | | | | | Use TARGET_T1024RDB from Kconfig instead. Signed-off-by: York Sun <york.sun@nxp.com> [trini: Get missing hunk in board/freescale/t102xrdb/ddr.c] Signed-off-by: Tom Rini <trini@konsulko.com>
* | powerpc: T1023RDB: Remove macro CONFIG_T1023RDBYork Sun2017-01-04-10/+10
|/ | | | | | Use TARGET_T1023RDB from Kconfig instead. Signed-off-by: York Sun <york.sun@nxp.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2017-01-02-4/+46
|\
| * udoo: neo: Fix indentationFabio Estevam2017-01-02-2/+2
| | | | | | | | | | | | The standard way is to put ifdef/endif in the very first column. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
| * imx6ul: geam6ul: Add MAINTAINERS for nand_defconfigJagan Teki2017-01-02-0/+1
| | | | | | | | | | | | | | | | | | Add Jagan as MAINTAINERS of configs/imx6ul_geam_nand_defconfig Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * mx6qsabreauto: Fix the EIM clock for the mx6qp variantFabio Estevam2017-01-02-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the MX6Q the aclk_eim_slow_podf field is '1' after POR, while on the MX6DQP it is '3'. This makes the EIM clock to be only 66MHz on the mx6qp variant, instead of 132 MHz. Instead of relying on the POR values for the CSMR1 register, make sure to manually configure the clk_eim_slow_sel field as '00' so that EIM clock is derived from AXI clock and the aclk_eim_slow_podf field as '1' so that EIM clock can be AXI clock divided by 2. This way a consistent EIM clock frequency is configured for all the mx6 variants. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
| * ARM: imx7s-warp: enable USB gadget ethernetKevin Hilman2017-01-02-0/+14
| | | | | | | | | | | | | | | | | | Enable USB gadget ethernet by default to have networking capabilities. Tested using DHCP and TFTP to transfer kernel, DT, ramdisk. Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
| * udoo_neo: Remove USDHC3 entryFabio Estevam2017-01-02-2/+1
| | | | | | | | | | | | | | | | Commit c94981efa20cc58 ("udoo_neo: Remove USDHC3 support") removed the SDHC3 support, but missed to remove the entry from the usdhc_cfg structure, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
* | arm: am57xx: cl-som-am57x: add ETH supportDmitry Lifshitz2017-01-02-0/+223
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add MAC support. Use PHY, connected to RGMII1 as a default Eth adapter, by appropriate setting of 'cpsw_data.active_slave'. 'cpsw_phy' env variable can override this setting. Set the MAC addresses in the U-Boot environment. The addresses are retrieved from the on-board EEPROM or from the SOC's MAC fuses. Set the following PHYs RGMII clock delays: - Enable RX delay - Disable TX delay Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> [uri.mashiach@compulab.co.il: add RGMII clock delays] Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@konsulko.com>
* | arm: am57xx: cl-som-am57x: fetch board rev from EEPROMDmitry Lifshitz2017-01-02-0/+14
| | | | | | | | | | | | | | | | | | | | | | Add PCB revision message. Implement board revision get_board_rev API. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Commit description update. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@konsulko.com>
* | arm: am57xx: cl-som-am57x: add initial board supportDmitry Lifshitz2017-01-02-0/+429
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Features supported : * Serial console * SPI Flash * MMC/SD Card * eMMC storage * SATA * PCA9555 - GPIO expander over I2C5 bus * USB Use spl alternate boot device feature to define fallback to the main boot device as it is defined by hardware. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> [uri.mashiach@compulab.co.il: Adjust to v2016.11] Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* | digsy_mtc.c: Minor spelling/grammar fixes.Robert P. J. Day2017-01-02-2/+2
|/ | | | Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
* mmc: move some SDHCI related options to KconfigMasahiro Yamada2016-12-29-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While I moved the options, I also renamed them so that they are all prefixed with MMC_SDHCI_. This commit was created in the following steps. [1] Rename with the following command find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e ' s/CONFIG_MMC_SDMA/CONFIG_MMC_SDHCI_SDMA/g s/CONFIG_BCM2835_SDHCI/CONFIG_MMC_SDHCI_BCM2835/g s/CONFIG_KONA_SDHCI/CONFIG_MMC_SDHCI_KONA/g s/CONFIG_MV_SDHCI/CONFIG_MMC_SDHCI_MV/g s/CONFIG_S5P_SDHCI/CONFIG_MMC_SDHCI_S5P/g s/CONFIG_SPEAR_SDHCI/CONFIG_MMC_SDHCI_SPEAR/g ' [2] create the Kconfig entries in drivers/mmc/Kconfig [3] Move the options by the following command tools/moveconfig.py -y MMC_SDHCI_SDMA MMC_SDHCI_BCM2835 \ MMC_SDHCI_KONA MMC_SDHCI_MV MMC_SDHCI_S5P MMC_SDHCI_SPEAR [4] Sort drivers/mmc/Makefile for readability Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: move CONFIG_SDHCI to Kconfig, renaming to CONFIG_MMC_SDHCIMasahiro Yamada2016-12-29-1/+1
| | | | | | | | | | | | | | | | | | | | | | | Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI. My motivation for the rename is, ultimately, to make all the MMC options prefixed with MMC_ and SDHCI options with MMC_SDHCI_, like Linux. This commit was created as follows: [1] Rename the config option with the following command: find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g' [2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig [3] run "tools/moveconfig.py -y MMC_SDHCI" [4] add "depends on MMC_SDHCI" to existing SDHCI driver entries Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* imx: mx6sllevk: add MAINTAINERS filePeng Fan2016-12-27-0/+7
| | | | | | | add MAINTAINERS files Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* board: samsung: update the MAINTAINERS fileJaehoon Chung2016-12-27-5/+5
| | | | | | Update the maintainer from Przemyslaw and Lukasz to me. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
* Update Maintainer and Author's email addressAjay Bhargav2016-12-27-3/+3
| | | | | | | | I am not longer using my old email address "ajay.bhargav@einfochips.com". For U-Boot development email address is now updated to contact@8051projects.net Signed-off-by: Ajay Bhargav <contact@8051projects.net>
* Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini2016-12-23-424/+1
|\
| * spi: Zap mpc52xx_spi.c, config and related codeJagan Teki2016-12-21-424/+1
| | | | | | | | | | | | | | | | | | armada100_spi.c, related config options and related codes are zapping becuase of "no DM conversion". Cc: Werner Pfister <Pfister_Werner@intercontrol.de> Signed-off-by: Jagan Teki <jagan@openedev.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM64: zynqmp: Replace board specific with generic memory bank decodingNathan Rossi2016-12-20-109/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The dram_init and dram_init_banksize functions were using a board specific implementation for decoding the memory banks from the fdt. This board specific implementation uses a static variable 'tmp' which makes these functions unsafe for execution from within the board_init_f context. This change makes the dram_init* functions use a generic implementation of decoding and populating memory bank and size data. Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Fixes: 8d59d7f63b ("ARM64: zynqmp: Read RAM information from DT") Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | ARM: zynq: Replace board specific with generic memory bank decodingNathan Rossi2016-12-20-109/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The dram_init and dram_init_banksize functions were using a board specific implementation for decoding the memory banks from the fdt. This board specific implementation uses a static variable 'tmp' which makes these functions unsafe for execution from within the board_init_f context. This unsafe use of a static variable was causing a specific bug when using the zynq_zybo configuration, U-Boot would generate the following error during image load. This was caused due to dram_init overwriting the relocations for the 'image' variable within the do_bootm function. Out of coincidence the un-initialized memory has a compression type which is the same as the value for the relocation type R_ARM_RELATIVE. Uncompressing Invalid Image ... Unimplemented compression type 23 It should be noted that this is just one way the issue could surface, other cases my not be observed in normal boot flow. Depending on the size of various sections, and location of relocations within __rel_dyn and the compiler/linker the outcome of this bug can differ greatly. This change makes the dram_init* functions use a generic implementation of decoding and populating memory bank and size data. Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Fixes: 758f29d0f8 ("ARM: zynq: Support systems with more memory banks") Cc: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | block: Move ceva driver to DMMichal Simek2016-12-20-11/+0
|/ | | | | | | | | This patch also includes ARM64 zynqmp changes: - Remove platform non DM initialization - Remove hardcoded sata base address Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-12-18-188/+6814
|\ | | | | | | | | | | Migrate CONFIG_ARCH_USE_MEMSET/MEMCPY with this merge. Signed-off-by: Tom Rini <trini@konsulko.com>
| * imx6: icorem6: Rename engicam icorem6 defconfig filesJagan Teki2016-12-16-14/+11
| | | | | | | | | | | | | | | | | | | | Rename defconfig files for better compatible with respective board names and dts files. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx6q: Add Engicam i.CoreM6 Solo/Duallite RQS Starter Kit initial supportJagan Teki2016-12-16-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from MMC: ------------- U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07) Trying to boot from MMC1 U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07 +0530) CPU: Freescale i.MX6DL rev1.3 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 DualLite/Solo RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl-rqs> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx6q: Add Engicam i.CoreM6 Quad/Dual RQS Starter Kit initial supportJagan Teki2016-12-16-0/+453
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from MMC: ------------- U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44) Trying to boot from MMC1 U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44 +0530) CPU: Freescale i.MX6D rev1.2 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl-rqs> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * imx6: geam6ul: Add NAND supportJagan Teki2016-12-16-0/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add NAND support for Engicam GEAM6UL board. Boot Log: -------- U-Boot SPL 2016.11-g537fa5f (Nov 28 2016 - 11:42:28) Trying to boot from NAND NAND : 256 MiB U-Boot 2016.11-g537fa5f (Nov 28 2016 - 11:20:06 +0100) CPU: Freescale i.MX6UL rev1.1 69 MHz (running at 396 MHz) CPU: Automotive temperature grade (-40C to 125C) at 42C Reset cause: WDOG Model: Engicam GEAM6UL DRAM: 128 MiB NAND: 256 MiB MMC: FSL_SDHC: 0 * Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx6ul: Add Engicam GEAM6UL Starter Kit initial supportJagan Teki2016-12-16-0/+298
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot Log: -------- U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30) Trying to boot from MMC1 U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530) CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 43C Reset cause: POR Model: Engicam GEAM6UL DRAM: 128 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 geam6ul> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>