summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
* MLK-14533 mx7ulp_evk: Change APLL and its PFD0 frequenciesYe Li2017-06-12-2/+26
| | | | | | | | | | | | | | | | | | | | | | | To support HDMI display on EVK board, the LCDIF pix clock must be 25.2Mhz. Since the its PCC divider range is from 1-8, the max rate of LCDIF PCC source clock is 201.6Mhz. This limits the source clock must from NIC1 bus clock or NIC1 clock, other sources from APLL PFDs are higher than this max rate. The NIC1 bus clock and NIC1 clock are from DDRCLK whose parent source is APLL PFD0, so we must change the APLL PFD0 and have impact to DDRCLK, NIC1 and NIC1 bus. Eventually, this requests to set the APLL PFD0 frequency to 302.4Mhz (25.2 * 12), with settings: PFD0 FRAC: 32 APLL MULT: 22 APLL NUM: 2 APLL DENOM: 5 Signed-off-by: Ye Li <ye.li@nxp.com> Tested-by: Fancy Fang <chen.fang@nxp.com> (cherry picked from commit 91be2789a93288cc087cd9e8db522c8308ef007c) (cherry picked from commit 40fd4ea8d86142a7182d13a99db4f2b4d1b55d35)
* MLK-14958 mx6slevk: Move setup_spi to board_initYe Li2017-05-22-5/+7
| | | | | | | | Current setup_spi is in board_early_init_f which is too early, so gpio_request can't reserve the gpio successfully. Move it to board_init. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 7c1b220f77313d9df84dbaf0da6ac820e85cba9a)
* MLK-14915 mx6ul_arm2/mx6ull_arm2: Fix ENET PHY reset issueYe Li2017-05-15-27/+59
| | | | | | | | | There are two pins used for ENET PHY reset, need to assert them before init the PHY. Current DM driver does not have such operation, need board level codes to handle. This patch moves the PHY reset operation into setup_fec, which is common for DM driver and non-DM driver. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14890 i2c: Enable I2C force idle busYe Li2017-05-15-9/+15
| | | | | | | | | | | This patch enables the I2C force idle bus for all i.MX6 and i.MX7 boards to avoid i2c bus problem during reboot. To use it, we must add some i2c properties in DTB file and the GPIO pinctrl for i2c. For mx6qsabreauto, mx6slevk, mx6sxsabresd and mx6sxscm, these boards call the setup_i2c. To remove conflict, change to use "setup_i2c" only for non-DM i2c driver. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14891 mx6slevk/mx6sll_arm2: Fix SPINOR CS GPIO usingYe Li2017-05-14-0/+4
| | | | | | | Needs to request the GPIO pin before assigning to GPIO to SPI driver which will directly setting it to output without request it. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14808 mx6sxsabresd: Fix wrong configuration name for QSPI bootYe Li2017-05-10-1/+1
| | | | | | | A wrong config name is used for QSPI boot, it causes IVT offset wrong. Fix the typo issue. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14845 mx6/mx7: Not call usb setup functions used by non-DM driverYe Li2017-05-09-1/+101
| | | | | | | | | | | Use CONFIG_DM_USB to comment out USB setup functions used by non-DM driver. So they won't be executed when using DM driver. These USB setup functions may setup power control pins to USB_PWR function not GPIO, which is different as the GPIO function used by USB vbus-supply. And cause the power control not work. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14779 mx6qdlsabreauto: Fix usb detect issueYe Li2017-05-08-26/+6
| | | | | | | | The recent ehci-mx6 driver can support vbus-supply property, no need to request io expander pins in usb setup. If did this, the regulator for vbus-supply will fail to get due to the pin is occupied. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14777 imx: mx6ul/mx6ull/mx7d: correct the usage of the macro ↵Fugang Duan2017-05-04-14/+14
| | | | | | | | | | | | | PFUZE3000_SW1AB_SETP() Commit:894a4b4da7e2 add the voltage configuration macro that base on the 0.1mV precision, and i.MX6UL/i.MX6ULL/i.MX7D use the macro as 1mV prevision that cause the conversion are wrong, then some boards cannot boot up in ldo bypass mode. The patch just correct the usage of PFUZE3000_SW1AB_SETP(). Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
* MLK-14776 imx6sl: add enet phy reset to i.MX6SL EVK boardFugang Duan2017-05-03-7/+8
| | | | | | | | For some i.MX6SL evk board, enet phy need reset. Add phy reset before phy clock enable and init the pinctrl earlier. Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
* MXSCM-292-2 mx6sxscm: convert to enable OF_CONTROL and DM driversJuan Gutierrez2017-04-28-16/+148
| | | | | | | | | | | | | Update mx6sxscm boards code and build configurations to enable OF_CONTROL and DM drivers. 1. Update GPIO codes for adding gpio request 2. Update PMIC and LDO by-pass codes for DM PMIC 3. Add lpddr2 512MB size and eMMC options tolocal Kconfig 4. Update license with NXP 2017 5. Add defconfigs for EVB boards Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
* MXSCM-292-1 mx6sxscm: add mx6sxscm boards codeJuan Gutierrez2017-04-28-0/+1321
| | | | | | | Move the scm mx6sxscm board generic support code from v2016.03 as the base for converting to use DTB OF_CONTROL Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
* MXSCM-291 mx6dqscm: set runtime fdt_file and other fixesJuan Gutierrez2017-04-28-3/+34
| | | | | | | | 1. set fdt_file according to board_rev which is set at runtime 2. Add macros for proper delimitation for different board builds 3. Fix and add proper iomux configuration Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
* MXSCM-290-2 mx6dqscm: convert to enable OF_CONTROL and DM driversJuan Gutierrez2017-04-28-90/+261
| | | | | | | | | | | | | | | Update mx6dqscm boards code and build configurations to enable OF_CONTROL and DM drivers. 1. Update GPIO codes for adding gpio request 2. Enable USB DM driver 3. Update PMIC and LDO by-pass codes for DM PMIC 4. Add spinor boot support 5. Add lpddr2 modes, sizes and boards on local Kconfig 6. Update license with NXP 2017 7. Add defconfigs for qwks boards Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
* MXSCM-290-1 mx6dqscm: add mx6dqscm boards codeJuan Gutierrez2017-04-28-0/+2569
| | | | | | | Move the scm mx6dqscm board generic support code from v2016.03 as the base for converting to use DTB OF_CONTROL. Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
* MLK-13141 mx6qpsabresd: Do not touch VGEN3 and VGEN5Robin Gong2017-04-21-23/+28
| | | | | | | | | | VGEN3 and VGEN5 have been fused the right value in PF0100 on i.mx6qp board, so software didn't need to change their voltage output anymore. Otherwise, VGEN3 will be wrongly updated from 1.8v to 2.8v. Signed-off-by: Robin Gong <yibin.gong@nxp.com> (cherry picked from commit 6f7f185664a401f03f6ce6c81b996c1f27fdbe73) Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14365 nand: replace the CONFIG_SYS_USE_NANDYe Li2017-04-06-2/+2
| | | | | | | The CONFIG_SYS_USE_NAND is not used in v2017.03. We have to replace it by other NAND configurations, like CONFIG_CMD_NAND or CONFIG_NAND_MXS. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-12527-5 android: Miss pad setting for buttonYe Li2017-04-06-0/+2
| | | | | | The button pad setting is missed during cherry-pick. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-13499 imx6sll: add epdc splash screen supportRobby Cai2017-04-06-0/+226
| | | | | | | | | add splash screen feature for epdc. it's tested on imx6sll arm2 board and evk board. Signed-off-by: Robby Cai <robby.cai@nxp.com> (cherry picked from commit c85c6f2a0f08dfc6c2859fe969b2021ab32b9370) Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-13586-2 mx7d_arm2/sabresd: Update ddr3 script to V2.0 for Bank interleaveYe Li2017-04-05-109/+155
| | | | | | | | | | | | | | | | | | | | | | | To improve the performance, enable the bank interleave for DDR3. Update the DDR3 settings to new script IMX7D_DDR3_533MHz_1GB_32bit_V2.0.ds Changes: 1. Enable bank interleave 2. Improve the drive strength for non-TO1.1 chips. 3. Updates ZQ_CON0 settings. 4. For 19x19 DDR3 ARM2 and 12x12 DDR3 ARM2, they are using old version scripts which were not upgrade with SABRESD script. According to DDR owner suggestion, to use same version script for all of them. File: http://compass.freescale.net/livelink/livelink?func=ll&objid=233861153&objAction=browse&sort=name&viewType=1 Test: Passed stress test on one TO1.2 SABRESD, one TO1.1 SABRESD and one TO1.0 SABRESD. Passed stress test on one 12x12 ddr3 ARM2. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 62e73b45c53e3302d869c373da72699199b90648)
* MLK-13586-1 mx7d_arm2: Update lpddr3 script to V2.0 for Bank interleaveYe Li2017-04-05-60/+88
| | | | | | | | | | | | | | | | | | | | | To improve the performance, enable the bank interleave for LPDDR3. Update the LPDDR3 settings to new script IMX7D_LPDDR3_533MHz_2GB_32bit_V2.0.ds5. Changes: 1. Enable bank interleave 2. Improve the drive strength for non-TO1.1 chips. 3. Updates ZQ_CON0 settings. 4. Change to 0 for reserved bits. File: http://compass.freescale.net/livelink/livelink?func=ll&objid=233861153&objAction=browse&sort=name&viewType=1 Test: Passed stress test on one 19x19 lpddr3 arm2 and one 12x12 lpddr3 arm2. Passed LPSR test on one 12x12 lpddr3 arm2. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 9a4fa3f8d2762791a76fd90e83feec8c8c9235b0)
* MLK-14248-3: mx6ul: update lpddr2 script to latest versionAdrian Alonso2017-04-05-2/+2
| | | | | | | | | | Update lpddr2 settings to latest version IMX6UL_LPDDR2_400MHz_16bit_V1.1.inc Use pre-charge command 0x1 per DDR register programming aid Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com> (cherry picked from commit e7aa25c2c7313b00475e3e0ce394a2fbaa569fbd)
* MLK-14248-1: mx6sl: update lpddr2 script to latest versionAdrian Alonso2017-04-05-2/+2
| | | | | | | | | | Update lpddr2 settings to latest version MX6SL_MMDC_LPDDR2_register_programming_aid_v0.9.inc Use pre-charge command 0x1 per DDR register programming aid Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com> (cherry picked from commit 7c15f3afbd2cfa97b14a0013ef959e9e73fd2f1e)
* MLK-13539: mx6sl: evk: lpddr2: add pre charge command allAdrian Alonso2017-04-05-0/+1
| | | | | | | | | | | | | LPDDR2 script MX6SL_MMDC_LPDDR2_register_programming_aid_v0.9.inc Updated to add Precharge all command per JEDEC The memory controller may optionally issue a precharge-all command prior to the MRW reset command This is strongly recommended to ensure robust DRAM initialization Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 498f4a791593069220213c6d777527f4d899fb8a)
* MLK-13407: mx6qarm2: mt128x64mx3 2: add init pre charge all commandAdrian Alonso2017-04-05-3/+10
| | | | | | | | | | | | | | - Adjust ZQ delay for MMDC clock frequency at 400MHz - Precharge all commands per JEDEC The memory controller may optionally issue a Precharge-All command prior to the MRW Reset command, this is strongly recommended to ensure a robust DRAM initialization DDR Calibration script: http://sw-stash.freescale.net/projects/IMX/repos/ddr-scripts-rel/commits/a72e010a1fd8c7fe0fda7bdc4d058c478e94c3da Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com> (cherry picked from commit 03cc626df73d6c2bb36daf280b1cd43170c298a0)
* MLK-13131: mx6qarm2: add fastboot and recovery supportAdrian Alonso2017-04-05-0/+33
| | | | | | | Add fastboot and recovery mode support for mx6qarm Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com> (cherry picked from commit 505e899ce582118da28ca1f4487ce7f179225bd7)
* MA-9213 imx: mx7ulp-evk: Add android supportSanshan Zhang2017-04-05-0/+58
| | | | | | | | | | | Add android features on i.MX7ULP EVK board. Implement the code to get boot device and the serial number on mx7ulp. TODO: will add the code which check misc partition after porting BCB. Change-Id: I9d06fecba303fa4dfdcaf73da1b6246444697bba Signed-off-by: Sanshan Zhang <sanshan.zhang@nxp.com> (cherry picked from commit 4c60cba3a017b921aebb84dd1268c898e549c99a) Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-12527-3 android: Add board support to enable android fastbootYe Li2017-04-05-1/+748
| | | | | | | | | | | | Add board level support for android fastboot feature. Each board has a android specified header file for defining android related configuraitons. And add build targets for their android uboot images building. For mx6qsabreauto, mx6sabresd and mx7dsabresd, we enable the android fastboot exclusive with DFU. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 43fe988af28c5e51fb23aa846e04bc9698256926)
* MLK-12527-2 android: Add FSL android fastboot supportYe Li2017-04-05-0/+81
| | | | | | | | | | | | | | | | | | | | | | Integrate the FSL android fastboot features into community's fastboot. 1. Use USB gadget g_dnl driver 2. Integrate the FSL SD/SATA/NAND flash operations, since the GPT and EFI partitions are not support by i.MX. 3. Add FDT support to community's android image. 4. Add a new boot command "boota" for android image boot. The boota implements to load ramdisk and fdt to their loading addresses specified in boot.img header, while bootm won't do it for android image. 5. Support the authentication of boot.img at the "load_addr" for both SD and NAND. 6. We use new configuration CONFIG_FSL_FASTBOOT for Freescale's fastboot with relevant header file "fsl_fastboot.h". While disabling the configuration, the community fastboot is used. 7. Overwrite the cmdline in boot.img by using bootargs saved in local environment. 8. Add recovery and reboot-bootloader support. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 23d63ff185929fff5e392efc853d69b606ba081a)
* MLK-14484-3 mx7ulp_arm2: Convert to use OF_CONTROLYe Li2017-04-05-13/+1
| | | | | | | | | | Add the 10x10 ARM2 and 14x14 ARM2 DTS files. Also convert the board codes to use OF_CONTROL and DM drivers. Since the DTS files only have UART and SD1 supported. So we only enable the DM for these two modules. QSPI and USB are still kept in non-DM fashion. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14484-2 mx7ulp_arm2: Add 10x10 and 14x14 ARM2 codesYe Li2017-04-05-0/+925
| | | | | | | | | | | | | Copy the mx7ulp ARM2 codes from v2016.03 as the base for using OF_CONTROL and DM drivers. The 14x14 ARM2 LPDDR3 script is v1.5: - IMX7ULP1_LPDDR3_320MHz_512MB_32bit_V1.5.inc The 10x10 ARM2 LPDDR2 script is v1.1: - IMX7ULP1_LPDDR2_320MHz_1GB_32bit_V1.1.inc Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14445-8 mx7ulp_evk: Add dynamical MMC device detectionYe Li2017-04-05-0/+14
| | | | | | | Add board_late_mmc_env_init to support MMC device detection for environment variables. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-13929-6 mx7ulp_evk: Enable the MIPI DSI splashscreenYe Li2017-04-05-0/+70
| | | | | | | | Enable and setup board level codes for MIPI DSI splashscreen on EVK board. User needs set env variable"panel=HX8363_WVGA" for displaying. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 49cb68f5c17e42f9290336e1252ace6ac7d0b5ce)
* MLK-14445-6 mx7ulp_evk: Add USB OTG0 supportYe Li2017-04-05-0/+39
| | | | | | | Porting codes to support USB OTG0 on the EVK board. Convert to use DM USB driver. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14445-2 mx7ulp_evk: Add QSPI flash supportYe Li2017-04-05-0/+35
| | | | | | | | | Porting the QSPI flash board support from v2016.03, and convert to use DM QSPI driver. Since we need to support QSPI at default in u-boot, change the default DTS file to qspi enabled DTS. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-13925-1 mx7ulp_evk: Update LPDDR3 script to V1.4Ye Li2017-04-05-18/+4
| | | | | | | | | | | | | | | | | | | | Update LPDDR3 script from v1.2 to v1.4 EVK_IMX7ULP1_LPDDR3_320MHz_1GB_32bit_V1.4.inc with the changes below: Version 1.3 -Update the precharge command to CMD=01 at the DDR initialization phase Version 1.4 -remove unimplemented registers Write data bit delay --refer to the DDR_TRIM bits in IOMUXC1_DDR_SW_PAD_CTL_PAD_DDRn File: http://compass.freescale.net/livelink/livelink?func=ll&objid=235761218&objAction=browse&sort=name&viewType=1 Test: One EVK board passes overnight stress test. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit e3343cb38eac2cc69b58247b5adcb500e5f19834)
* MLK-13924 mx7ulp: Fix APLL num and denom setting issueYe Li2017-04-05-24/+1
| | | | | | | | | | | | | For the current APLL setting, as we want the APLL PFD0 to meet DDR clock 320Mhz requirement. We set MULT to 20, NUM to 4 and DENOM to 2, to get final 22 multiplier. But according to the RM, the NUM should always be less than the DENOM. So our setting violates the rule. Actually the ROM has already set the MULT to 22 and leave NUM/DENOM in default value. The calculated APLL PFD0 clock is 318.9888Mhz, which also meet the DDR requirement. To fix the issue, we remove the PLL settings in DCD to use default value from ROM, and only set the PFD0 FRAC. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 8cc70b1ded5309dee522aa00b43bd702a209ba51)
* imx: imx7ulp: add EVK board supportPeng Fan2017-04-05-0/+438
| | | | | | | | | | | | | | | | | | | | | | | | Add EVK board support. Add the evk dts file. LOG: U-Boot 2017.03-rc2-00038-gab86c1d (Feb 22 2017 - 15:59:58 +0800) CPU: Freescale i.MX7ULP rev1.0 at 500 MHz Reset cause: POR Boot mode: Dual boot Model: NXP i.MX7ULP EVK DRAM: 1 GiB MMC: FSL_SDHC: 0 In: serial@402D0000 Out: serial@402D0000 Err: serial@402D0000 Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* MLK-14419-3 imx: mx7d_arm2: add 19x19 LPDDR2/LPDDR3/DDR3 ARM2 supportPeng Fan2017-04-05-0/+2626
| | | | | | | | | Add 19x19 LPDDR2/LPDDR3/DDR3 ARM2 board supports. Enable the OF_CONTROL and convert them to use DM driver. Since the DTB lacks the support for some modules. We have to use QSPI and FEC with non-DM driver. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14419-2 imx: mx7d_arm2: add 12x12 ddr3 arm2 board supportPeng Fan2017-04-05-0/+644
| | | | | | | | Add 12x12 ddr3 arm2 board support and convert it to use OF_CONTROL and DM drivers. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14419-1 imx: mx7d_arm2: add 12x12 lpddr3 arm2 supportPeng Fan2017-04-05-0/+1493
| | | | | | | | Add mx7d 12x12 lpddr3 arm2 support, which has enabled the OF_CONTROL and DM drivers Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14418-13 imx: mx7dsabresd: Update Misc codesYe Li2017-04-05-6/+15
| | | | | | | | 1. Add BMODE support 2. Update environment variables to align with v2016.03 3. Remove the wdog WCR bit 4 clear. Since we have implemented reset_cpu for mx7d. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14418-12 imx: mx7dsabresd: Update LCD splash screen codesYe Li2017-04-05-10/+27
| | | | | | | Update LCD setup codes to use the parameters structure used for all i.mx platforms, discard to use videmode environment variable. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14418-10 imx: mx7dsabresd: update ddr script and add plugin supportPeng Fan2017-04-05-0/+360
| | | | | | Update ddr script and add plugin support. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* MLK-14418-9 imx: mx7dsabresd: add nand/qspi boot supportPeng Fan2017-04-05-0/+4
| | | | | | | | | | Add nand/qspi build configurations for their boot support. Also Add gpmi-nand and qspi specified DTS files for enable them. For QSPI, this patch changes it to use DM driver. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14418-8 imx: mx7dsabresd: add epdc supportPeng Fan2017-04-05-0/+235
| | | | | | | | Add epdc support from v2016.03. Add a epdc specified DTS file for using epdc Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14418-7 imx: mx7dsabresd: add FEC DM supportPeng Fan2017-04-05-49/+92
| | | | | | | | Add FEC2 and convert to use FEC DM driver. Add board rev check. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14418-6 imx: mx7dsabresd: switch to DM USBPeng Fan2017-04-05-25/+0
| | | | | | Switch to use DM USB. Enable GPIO regulator to handle vbus supply. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* MLK-14418-5 imx: mx7dsabresd: reset ENET_RST_BPeng Fan2017-04-05-0/+16
| | | | | | | | Reset ENET_RST_B to make ENET function stable. Since DM_GPIO enabled, we use "gpio_spi@0_5" which corresponds to ENET_RST_B. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* MLK-14418-4 imx: mx7dsabresd: enable dm driversPeng Fan2017-04-05-256/+15
| | | | | | | Enable GPIO/I2C/MMC/SPI/74X164 DM drivers. Discard mxc spi support. Signed-off-by: Peng Fan <peng.fan@nxp.com>
generated by cgit v1.1 at 2024-11-14 16:06:46 +0000