summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
* am33xx: Drop gpio0_7_pin_mux from phytec pcm051Tom Rini2013-02-07-5/+0
| | | | | | | | This mux is not currently used and appears to be a carry-over from the am335x evm code. Acked-by: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Tom Rini <trini@ti.com>
* OMAP3: igep00x0: fix a build warning on IGEP boardsJavier Martinez Canillas2013-02-07-1/+1
| | | | | | | | | | | | | commit b689cd5 OMAP3: use a single board file for IGEP devices introduced the following build warning: igep00x0.h:168:24: warning: backslash-newline at end of file [enabled by default] This patch fixes the issue. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
* Add DDR3 support for AM335x-EVM (Version 1.5A)Jeff Lance2013-02-07-0/+41
| | | | | | | | | | | | | | AM335x EVM 1.5A uses Micron MT41J512M8RH-125 SDRAM 4Gb (512Mx8) as the DDR3 chip. [Hebbar Gururaja <gururaja.hebbar@ti.com>] - Resolve merge conflict while rebasing. File structure is changed in the mainline. So re-arrange the code accordingly. - Update commit message to reflect the DDR3 part number Signed-off-by: Jeff Lance <j-lance1@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
* am335x: display msg when reading MAC from efuseLars Poeschel2013-02-07-1/+1
| | | | | | | | When ethaddr is not set in environment the MAC address is read from efuse. The message was only printed in debug case, but this message could be of interest for the ordinary user, so printf it. Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
* pcm051: Add support for Phytec phyCORE-AM335xLars Poeschel2013-02-07-0/+478
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The board is named pcm051 and has this hardware: SOC: TI AM3359 DDR3-RAM: 2x MT41J256M8HX-15EIT:D 512MiB ETH 1: LAN8710AI SPI-Flash: W25Q64BVSSIG RTC: RV-4162-C7 I2C-EEPROM: CAT32WC32 NAND: MT29F4G08_VFPGA63 PMIC: TPS65910A3 LCD Supported: UART 1 MMC/SD ETH 1 USB I2C SPI Not yet supported: NAND RTC LCD Signed-off-by: Lars Poeschel <poeschel@lemonage.de> [trini: Add #define CONFIG_PHY_ADDR 0 to config] Signed-off-by: Tom Rini <trini@ti.com>
* OMAP3: igep00x0: add boot status GPIO LEDJavier Martinez Canillas2013-02-07-0/+21
| | | | | | | | | | | | | This patch adds an GPIO LED boot status for IGEP boards. The GPIO LED used is the red LED0 while the Linux kernel uses the green LED0 as the boot status. By using different GPIO LEDs, the user can know in which step of the boot process the board currently is. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* OMAP3: use a single board file for IGEP devicesJavier Martinez Canillas2013-02-07-333/+45
| | | | | | | | | | | | | | | | | Even when the IGEPv2 board and the IGEP Computer-on-Module are different from a form factor point of view, they are very similar in the fact that share many components and how they are wired. So, it is possible (and better) to have a single board file for both devices and just use the CONFIG_MACH_TYPE to make a differentiation between each board when needed. This change avoids code duplication by removing 298 lines of code and makes future maintenance easier. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* ARM: highbank: use wfi macro instead of inline asmRob Herring2013-02-03-1/+2
| | | | | | | Older compilers don't recognize v7 wfi instruction, so use wfi macro to fix builds on old compilers. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* arm: rmobile: kzm9g: Adjust ETM trace clockTetsuyuki Kobayashi2013-02-02-1/+1
| | | | | | | | Set ETM TRCLK down to 78MHz to get clear wave form. This patch makes difference only when you use ETM trace connecting JTAG debugger. Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp> Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
* arm: rmobile: kzm9g: Adjust SDRAM settingTetsuyuki Kobayashi2013-02-02-3/+14
| | | | | | | | | | After stress test, I found some of kzm9g board occures memory failure. This patch adust SDRAM setting. - Enlarge drivability on both SDRAM controller and SDRAM itself - Raise core voltage Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp> Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
* Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-02-02-715/+1262
|\
| * mx23evk: Add initial board supportOtavio Salvador2013-01-28-0/+234
| | | | | | | | | | | | | | | | | | | | The following features are supported: * 128 MB DDR1 SDRAM * DUART * SD/MMC Card Socket Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
| * mxs: mmc: mx23_olinuxino: Add MMC supportMarek Vasut2013-01-28-1/+30
| | | | | | | | | | | | | | | | | | Add support for the MMC attached to SSP1. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
| * mxs: mmc: Allow overriding default card detect implementationMarek Vasut2013-01-28-4/+4
| | | | | | | | | | | | | | | | | | | | Some MXS based boards do not implement the card-detect signal. Allow user to specify alternate card-detect implementation. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
| * mx6qsabrelite: search mii phy address 4-7Troy Kisky2013-01-28-3/+21
| | | | | | | | Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
| * mxs: Boost the memory power supplyMarek Vasut2013-01-28-1/+1
| | | | | | | | | | | | | | | | | | | | | | The memory power supply on MX23 didn't pump out enough juice into the DRAM chip, thus caused occasional memory corruption. Fix this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
| * imximage.cfg: run files through C preprocessorTroy Kisky2013-01-22-692/+769
| | | | | | | | | | | | | | | | | | | | | | | | The '#' used as comments in the files cause the preprocessor trouble, so change to /* */. The mkimage command which uses this preprocessor output was moved to arch/arm/imx-common/Makefile .gitignore was updated to ignore .cfgtmp files. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
| * woodburn: Set Write Protection GPIO as inputFabio Estevam2013-01-21-1/+2
| | | | | | | | | | | | Set Write Protection GPIO as input. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * mxs: Add MX23 olinuxino board supportMarek Vasut2013-01-21-0/+188
| | | | | | | | | | | | | | | | | | This patch adds support for MX23-based Olinuxino board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
| * mxs: clock: Use 'mxs' prefix for methodsOtavio Salvador2013-01-21-15/+15
| | | | | | | | | | | | | | Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
* | tegra: fdt: sort dts filesAllen Martin2013-01-17-92/+80
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Sort nodes in dts files according the the following rules: 1) Any nodes that already exist in any /include/d file, in the order they appear in the /include/d file. 2) Any nodes with a reg property, in order of their address. 3) Any nodes without a reg property, alphabetically by node name. Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | tegra: fdt: remove clocks nodesAllen Martin2013-01-17-127/+0
| | | | | | | | | | | | | | These nodes are unused. Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | tegra: remove IRDA pinmux synonymAllen Martin2013-01-16-2/+2
| | | | | | | | | | | | | | | | | | IRDA is a synonym for UARTB in tegra pinmux, remove all usage of this synonym and replace with UARTB to disambiguate. Signed-off-by: Allen Martin <amartin@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | Tegra30: fdt: Update DT files with I2C info for T30/CardhuTom Warren2013-01-16-0/+41
| | | | | | | | | | | | | | | | | | | | | | Note that T30 does not have a separate/different DVC (power I2C) controller like T20 - all 5 I2C controllers are identical, but DVC_I2C is still used to designate the controller intended for power control (PWR_I2C in the schematics). On Cardhu, it's used to access the PMU and EEPROM, as well as the audio codec, temp sensor, and fuel gauge devices from the OS. Signed-off-by: Tom Warren <twarren@nvidia.com>
* | Tegra30: Add/enable Cardhu build (T30 reference board)Tom Warren2013-01-16-0/+563
| | | | | | | | | | | | | | | | | | | | | | This build is stripped down. It boots to the command prompt. GPIO is the only peripheral supported. Others TBD. include/configs/tegra-common.h now holds common config options for Tegra SoCs. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* | Tegra30: Add generic Tegra30 build supportTom Warren2013-01-16-3/+14
| | | | | | | | | | | | | | | | This patch adds basic Tegra30 (T30) build support - no specific board is targeted. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* | Tegra30: Cardhu: Add DT filesTom Warren2013-01-16-0/+14
| | | | | | | | | | | | | | | | | | These are stripped down for bringup, They'll be filled out later to match-up with the kernel DT contents, and/or as devices are brought up (mmc, usb, spi, etc.). Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* | tegra: enable LCD on PAZ00Marc Dietrich2013-01-16-0/+43
| | | | | | | | | | | | | | | | This adds LCD panel descriptions to the device tree of PAZ00 and enables LCD support in the configuration. Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | tegra: display: add board pinmuxMarc Dietrich2013-01-16-0/+7
| | | | | | | | | | | | | | | | Boards may require a different pinmux setup for DISPALY than the default one. Add a way to call into board specific code to set this up. Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | tegra: Enable LCD on TECThierry Reding2013-01-16-0/+32
| | | | | | | | | | | | | | | | | | The TEC ships with a 7" LCD panel that provides a resolution of 800x480 pixels. Add a corresponding panel description to the device tree and enable LCD support in the configuration. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | tegra: Enable LCD on Medcom-WideThierry Reding2013-01-16-0/+32
|/ | | | | | | | | The Medcom-Wide has a 15" LCD panel with a resolution of 1366x768 pixels. Add a corresponding panel description to the device tree and enable LCD support in the configuration. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
* Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-01-14-27/+74
|\
| * mx51evk: Add DVI output supportFabio Estevam2013-01-13-5/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | Add DVI output support and make it the default video output. Currently the CLAA WVGA panel is supported, but this panel has to be purchased separately, so using the DVI output as the default would allow more people to try the splash screen feature on a mx51evk. If someone still wants to use the CLAA WVGA, just set the panel variable as: set panel claa Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * mx31/mx35/mx51/mx53/mx6: add watchdogTroy Kisky2013-01-13-17/+3
| | | | | | | | | | | | | | Use a common watchdog driver for all these cpus. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * mx53loco: Add support for SEIKO 4.3'' WVGA panelFabio Estevam2013-01-09-5/+35
| | | | | | | | | | | | | | | | | | | | | | Add support for the Seiko 4.3'' WVGA panel on mx53loco. By default, the CLAA WVGA panel is selected. In order to support the Seiko panel, the enviroment variable 'panel' must be set to 'seiko'. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD2013-01-14-42/+266
|\ \
| * | EXYNOS5: Make all display related code dependent on CONFIG_LCDAjay Kumar2013-01-11-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | u-boot compilation fails for smdk5250 when we deselect CONFIG_LCD from the main config file. Following error was observed: drivers/video/libvideo.o: In function `exynos_lcd_init': /home/ajay/u-boot-samsung/drivers/video/exynos_fb.c:68: undefined reference to `lcd_set_flush_dcache' This is because exynos video drivers have dependency on CONFIG_LCD. Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | EXYNOS5: Add support for FIMD and DPAjay Kumar2013-01-10-0/+97
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add panel_info structure required by LCD driver and DP panel platdata for SMDK5250. Add GPIO configuration for LCD. Enable FIMD and DP support on SMDK5250. DP Panel size: 2560x1600. We use 16BPP resolution to get LCD console. Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Acked-by: Simon Glass <sjg@chomium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | EXYNOS5: Add device node for PMICRajeshwari Shinde2013-01-10-0/+7
| | | | | | | | | | | | | | | | | | | | | Add device node for MAX77686 Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | SMDK5250: Enable VBus for USB 2.0 controllerVivek Gautam2013-01-08-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | This patch enables Vbus required for USB 2.0 controller. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | EXYNOS5 : FDT: Add Aliases for SPI deviceRajeshwari Shinde2013-01-08-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds aliases for SPI. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | EXYNOS5: FDT: Add sound and codec device nodeRajeshwari Shinde2013-01-08-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | Adds sound and codec device node parameters Signed-off-by: R. Chandrasekar <rcsekar@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | SMDK5250: Initialise I2C using FDTRajeshwari Shinde2013-01-08-19/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch initialises I2C using FDT. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | EXYNOS5 : FDT: Add Aliases for I2C deviceRajeshwari Shinde2013-01-08-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds aliases for I2C. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | spl:falcon:trats Update Trats default board configuration file to support ↵Łukasz Majewski2013-01-03-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FALCON MODE Support for a new command (defined at envs) - spl_export generates the ATAGS image necessary for fast boot. Afterwards, it is stored at ext4 partition. Generated image format: CRC [4B] SIZE [4B] PAYLOAD(ATAGS/DT) [SIZE] Remarks: - CRC is calculated only for PAYLOAD - SIZE is the size of PAYLOAD It is important to adjust ${splsize} when large image is generated. It is defined as hex, since ext4 related commands expect it. The ${spladdr} environment variable corresponds to CONFIG_SYS_SPL_ARGS_ADDR Additionally definitions for DFU have been refactored and support for EFI has been added as well. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | exynos5: Add DT based driver for SMC911X ethernetHatim RV2012-12-26-30/+85
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add device tree based ethernet driver for SMC911X controller on SMDK5250 boards. Signed-off-by: Hatim Ali <hatim.rv@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | EXYNOS5: FDT: add initial dts file for EXYNOS5250, SMDK5250Hatim RV2012-12-26-0/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds initial dts file for EXYNOS5250 SoC. This dts file currently include only ethernet devices and properties. More devices to be added in subsequent patches. Also add the dts file for SMDK5250 board which uses the EXYNOS5250 dts file. Signed-off-by: Hatim Ali <hatim.rv@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-01-11-86/+336
|\ \ \
| * \ \ Merge 'u-boot-atmel/master' into 'u-boot-arm/master'Albert ARIBAUD2013-01-09-0/+3
| |\ \ \
| | * | | at91sam9x5: enable USB support for 9x5ek board.Richard Genoud2012-12-09-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Acked-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
generated by cgit v1.1 at 2024-08-20 17:51:10 +0000