summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
* Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2014-11-26-9/+36
|\
| * arm: ls102xa: Select ge2_clk125 for eTSEC clock muxingAlison Wang2014-11-24-0/+1
| | | | | | | | | | | | | | | | | | | | EC1 pins in RCW can be selected as RGMII1, GPIO3, CAN1/2, FTM1 or SAI1/2. There is a bug that EC3 RGMII could not work when selecting EC1 as other functionality except RGMII. The workaround is to select ge2_clk125 for eTSEC clock muxing in register SCFG_ETSECCMCR. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * arm: ls102xa: Add SystemID EEPROM support for LS1021ATWR boardAlison Wang2014-11-24-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SystemID information could be read through I2C1 from EEPROM on LS1021ATWR board. As LS1 is a little-endian processor, getting the version ID by be32_to_cpu() is wrong. Fix it by using e.version directly. This change will be compatible for both ARM and PowerPC. As there is an errata that I2C1 could not work in SD boot, reading EEPROM through I2C1 is disabled too in SD boot. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * arm: ls102xa: Remove bit reversing for SCFG registersAlison Wang2014-11-24-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SCFG_SCFGREVCR is SCFG bit reverse register. This register must be written with 0xFFFFFFFF before writing to any other SCFG register. Then other SCFG register could be written in big-endian mode. Address: 157_0000h base + 200h offset = 157_0200h Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 W/R SCFGREV Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0-31 SCFGREV SCFG Bit Reverse Control Filed 32'h 0000_0000 - No bit reverse is applied 32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as 0:31 This patch removes the bit reversing for SCFG registers in u-boot. It will be implemented through PBI commands in RCW .pbi write 0x570200, 0xffffffff .end So other SCFG register could be written in big-endian mode in u-boot or kernel directly. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * arm: ls102xa: Add snoop disable for slave port 0, 1 and 2Jason Jin2014-11-24-0/+17
| | | | | | | | | | | | | | | | | | Disable the snoop for slave interface 0, 1 and 2 to avoid the interleaving on the CCI400 BUS. Signed-off-by: Jason Jin <Jason.Jin@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * qe: add qe support for ls1021a-twr boardZhao Qiang2014-11-19-0/+8
| | | | | | | | | | Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * qe: add qe support to ls1021aqdsZhao Qiang2014-11-19-0/+8
| | | | | | | | | | | | | | add qe support to ls1021aqds Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2014-11-26-9/+438
|\ \ | | | | | | | | | | | | | | | | | | Conflicts: drivers/mmc/fsl_esdhc.c Signed-off-by: Tom Rini <trini@ti.com>
| * | powerpc/t2080qds: fix for 1000BASE-KXShaohui Xie2014-11-19-0/+99
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1000BASE-KX(1G-KX) uses SGMII protocol but the serdes lane runs in 1G-KX mode. By default, the lane runs in SGMII mode, when a MAC uses a lane in 1G-KX mode, corresponding bit in PCCR1 for the lane needs to be set, and needs to fixup dtb accordingly for kernel to do proper initialization. Hwconfig "fsl_1gkx" is used to indicate a MAC runs in 1G-KX mode, FM1 MAC 1/2/5/6/9/10 are available for 1G-KX, MAC 3/4 run in RGMII mode. To set a MAC runs in 1G-KX mode, set its' corresponding env in "fsl_1gkx", 'fm1_1g1' stands for FM1-MAC1, 'fm1_1g2' stands for FM1-MAC2, etc. If all MAC 1/2/5/6/9/10 run in 1G-KX mode, the hwconfig should has below setting: fsl_1gkx:fm1_1g1,fm1_1g2,fm1_1g5,fm1_1g6,fm1_1g9,fm1_1g10 Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> [York Sun: Fix compiling warning] Reviewed-by: York Sun <yorksun@freescale.com>
| * | powerpc/t2080qds: fixup dtb for 10g-krshaohui xie2014-11-19-11/+98
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | XFI ports on t2080qds can work with fiber cable and direct attach cable(copper). We use hwconfig to define cable type for XFI, and fixup dtb based on the cable type. For copper cable, set below env in hwconfig: fsl_10gkr_copper:<10g_mac_name> the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4. fm1_10g1 stands for FM1-MAC9, fm1_10g2 stands for FM1-MAC10, fm1_10g3 stands for FM1-MAC1, fm1_10g4 stands for FM1-MAC2. The four <10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports, if a given 10G port will use the copper cable for 10GBASE-KR, set the <10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be assumed to be used for the port. For ex. if four XFI ports will both use copper cable, the hwconfig should contain: fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm1_10g3,fm1_10g4 Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | board/t2080qds: add readme for t2080qdsShengzhou Liu2014-11-19-0/+243
| |/ | | | | | | | | Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | Merge branch 'master' of http://git.denx.de/u-boot-samsungTom Rini2014-11-26-0/+64
|\ \
| * | odroid: Turn blue LED onSuriyan Ramasami2014-11-24-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | To indicate that U-Boot is active, turn on the blue LED. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | odroid: usbhost - Add missing gpio_request callSuriyan Ramasami2014-11-24-2/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The USB host code was missing gpio_request() calls before using the gpio functions, causing errors to be printed out. As a side note calls to max77686_set_buck_mode(OPMODE_OFF/OPMODE_ON) have been removed, as they did not have any effect. This is as per Przemyslaw: I looked into the documentation and there is a "ENB8" pin in PMIC package. This pin allows steering BUCK8 ON/OFF by the hardware. If ENB8 is set to low then you can do on/off. If high, then you cannot change its state by I2C write, which seems to be the case with the Odroids. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | arm: odroid: usb: add support for usb host including ethernetSuriyan Ramasami2014-11-17-0/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | This change adds support for enabling the USB host features of the board. This includes the USB3503A hub and the SMC LAN9730 ethernet controller as well. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Config: Exynos5800: Enable build for Peach-PiAkshay Saraswat2014-11-17-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds following things : - New config and defconfig for Peach-Pi board. - Alterations in Kconfig and MAINTAINERS. - Addition of CONFIG_EXYNOS5800. - ADdition of exynos5800-peach-pi in dts list. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | | Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini2014-11-26-0/+72
|\ \ \
| * | | sun7i: Set ARMV7_BOOT_SEC_DEFAULT when OLD_SUNXI_KERNEL_COMPAT is setHans de Goede2014-11-25-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Old kernels cannot handle booting in non-secure (hyp) mode, so when OLD_SUNXI_KERNEL_COMPAT is set, also set ARMV7_BOOT_SEC_DEFAULT. Note that whether to booting secure or non-secure can always be overriden using the bootm_boot_mode environment variable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | sun6i: Add gmac support for sun6i boardsHans de Goede2014-11-25-0/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Hookup the gmac found on the sun6i / A31 SoCs. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | sunxi: ahci: Add a delay after enabling target powerHans de Goede2014-11-25-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the target power is connected through a gpio, then give the target some time to power up before continuing with ahci / sata probing, this avoids link timeouts, without penalizing other boards where there is no target power gpio. Why 500 ms ? I started with 200, that was not enough, then I went to 500 which worked, lowering it to 350 broke things again, so 500 seems the minimum my vertex2 needs to be ready to get probed. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | sunxi: Add usb keyboard Kconfig optionHans de Goede2014-11-25-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | For use together with the hdmi console. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ian.campbell@citrix.com>
| * | | sunxi: video: Add simplefb supportLuc Verhaegen2014-11-25-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add simplefb support, note this depends on the kernel having support for the clocks property which has recently been added to the simplefb devicetree binding. Signed-off-by: Luc Verhaegen <libv@skynet.be> [hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as disussed on the devicetree list] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>.
| * | | sunxi: video: Add cfb console driver for sunxiLuc Verhaegen2014-11-25-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds a fixed mode hdmi driver for the sunxi platform. The fixed mode is a relatively safe 1024x768, more complete EDID handling is currently not provided. Only HDMI is supported today. This code is enabled when HPD detects an attached monitor. Current config is such that 8MB is shaved off at the top of the RAM. This avoids several memory handling issues, most significant is the fact that on linux on ARM you are not allowed to remap known RAM as IO. A clued in display driver will be able to recycle this reserved RAM in future though. cfbconsole was chosen as it provides the most important functionality: a working u-boot console, allowing for the debugging of certain issues without the need for a UART. Signed-off-by: Luc Verhaegen <libv@skynet.be> [hdegoede@redhat.com: Major cleanups and some small bugfixes] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | Merge git://git.denx.de/u-boot-fdtTom Rini2014-11-26-164/+355
|\ \ \ \ | |/ / / |/| | |
| * | | fdt: Try to use fdt_address_cells()/fdt_size_cells()Simon Glass2014-11-21-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use these new functions where possible. They default to a value of 2 so we cannot use them in some places where we need a default value of 1. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
| * | | fdt: Allow ft_board_setup() to report failureSimon Glass2014-11-21-161/+351
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This function can fail if the device tree runs out of space. Rather than silently booting with an incomplete device tree, allow the failure to be detected. Unfortunately this involves changing a lot of places in the code. I have not changed behvaiour to return an error where one is not currently returned, to avoid unexpected breakage. Eventually it would be nice to allow boards to register functions to be called to update the device tree. This would avoid all the many functions to do this. However it's not clear yet if this should be done using driver model or with a linker list. This work is left for later. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-11-24-0/+2
|\ \ \ \
| * | | | ARM: Add arch/arm/cpu/armv7/Kconfig with non-secure and virt optionsHans de Goede2014-11-24-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add arch/arm/cpu/armv7/Kconfig with non-secure and virt options, this is a preparation patch for adding an env variable to choose between secure / non-secure boot on non-secure boot capable systems, specifically this prepares for adding CONFIG_ARMV7_BOOT_SEC_DEFAULT as a proper Kconfig option. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | | | | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2014-11-24-349/+458
|\ \ \ \ \
| * | | | | mx6boards: Fix error handling in board_mmc_init()Fabio Estevam2014-11-24-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Cc: Eric Benard <eric@eukrea.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | | nitrogen6x: Fix error handling in board_mmc_init()Fabio Estevam2014-11-24-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Cc: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | | ot1200: Fix error handling in board_mmc_init()Fabio Estevam2014-11-24-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Cc: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | | arm: mx6: cm_fx6: implement board specific sata stopNikita Kiryanov2014-11-24-3/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Provide board specific implementation for sata stop command for cm_fx6. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de>
| * | | | | gw_ventana: Use the generic spl_sd.cfgFabio Estevam2014-11-24-23/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | gw_ventana can boot from SPI or NAND and both of these interfaces boot from the same 0x400 offset. This means that we could simplify the code and replace the custom gw_ventana.cfg with the generic spl_sd.cfg, as it provides the same boot offset of 0x400. Cc: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | | mx53ard: Fix error handling in board_mmc_init()Fabio Estevam2014-11-21-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | | mx53evk: Fix error handling in board_mmc_init()Fabio Estevam2014-11-21-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | | mx53smd: Fix error handling in board_mmc_init()Fabio Estevam2014-11-21-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | | mx6qarm2: Fix error handling in board_mmc_init()Fabio Estevam2014-11-21-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | | mx51evk: Fix error handling in board_mmc_init()Fabio Estevam2014-11-21-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | | tbs2910: Fix error handling in board_mmc_init()Soeren Moch2014-11-21-7/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Based on similar patches by Fabio Estevam for mx6sabresd, mx53loco, wandboard Signed-off-by: Soeren Moch <smoch@web.de> Acked-by: Stefano Babic <sbabic@denx.de>
| * | | | | imx: imx6q/dlsabreauto: Add PMIC Pfuze100 supportYe.Li2014-11-20-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the pfuze100 initialization in power_init_board for imx6q/dl sabreauto board. Signed-off-by: Ye.Li <B37916@freescale.com>
| * | | | | imx: mx6sxsabresd: Use the pfuze common init functionYe.Li2014-11-20-41/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Modify the pfuze init for mx6sxsabresd to use the shared "pfuze_common_init" function. And move this initialization to power_init_board. Signed-off-by: Ye.Li <B37916@freescale.com>
| * | | | | imx: mx6sabresd: Use the pfuze common init functionYe.Li2014-11-20-43/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Modify the pfuze init for mx6sabresd to use the shared "pfuze_common_init" function. And move this initialization to power_init_board. Signed-off-by: Ye.Li <B37916@freescale.com>
| * | | | | imx: mx6sabre common: Factorize the Pfuze init functionYe.Li2014-11-20-0/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the Pfuze initializations are similar on various mx6 SABRE boards. Factorize the initialization to a common function in file board/freescale/common/pfuze.c. So that all SABRE boards BSP can share the function. Signed-off-by: Ye.Li <B37916@freescale.com>
| * | | | | imx: mx6sxsabresd: Add board support for USDHC2 and USDHC3Ye.Li2014-11-20-5/+94
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add full support for USDHC2, USDHC3, USDHC4 on mx6sx sabresd board. The default boot socket is USDHC4, so the MMC environment device and mmcdev variable are set to this device. Signed-off-by: Ye.Li <B37916@freescale.com>
| * | | | | mx6sabresd: Access SRC_SBMR1 register via structureFabio Estevam2014-11-20-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In U-boot it is preferred to access the register via structure pointer, so convert it such style. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | | tqma6: use imx_ddr_sizeMarkus Niebel2014-11-20-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
| * | | | | tqma6: add warning on failed setup_i2cMarkus Niebel2014-11-20-4/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | setup_i2c has a return value. Use it to give feedback on error. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
| * | | | | tqma6: add missing includeMarkus Niebel2014-11-20-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add include needed to have prototype for board_spi_cs_gpio Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
| * | | | | mx6sabresd: Add mx6sabresd_spl_defconfig to MAINTAINERS entryFabio Estevam2014-11-20-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Let's add mx6sabresd_spl_defconfig entry into MAINTAINERS, so that we avoid getting a warning that the mx6sabresd_spl is not maintained. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
generated by cgit v1.1 at 2024-11-18 15:55:04 +0000