summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
* km_arm: enable POST for these boardsValentin Longchamp2011-10-05-0/+33
| | | | | | | | | | | | The current km_arm boards have a Power-On test jumper. When this jumper is set, this triggers some Power-On tests on the board. This patch enables the support of this jumper for starting the memory_regions test when the jumper is set. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com>
* TQM8xx: make room for growing code size due to I/O accessor cleanupWolfgang Denk2011-10-05-136/+2
| | | | | | | | | | | | | Commit "PPC: Cleanup tqm8xx_pcmcia.c" will clean up the PCMCIA code to use I/O accessors instead of plain volatile pointer accesses. This will result in about 300 byte bigger code. Fix custom linker script to make room for this. While we are at it, drop unmaintained u-boot.lds.debug linker script. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Tested-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk2011-10-04-35/+35
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-nand-flash: PPC: Fix socrates NAND problem PPC: Fix fsl_upm.c by renaming nand handling functions NAND: Make page, erase, oob size available via cmd_nand mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi NAND: Add -y option to nand scrub command NAND: Add nand read.raw and write.raw commands NAND: Really ignore bad blocks when scrubbing spl, nand: add 4bit HW ecc oob first nand_read_page function mxc_nand: fix a problem writing more than 32MB mxc_nand: fixed some typos (cosmetic) nand: increase chip_delay in mv kirkwood nand driver
| * PPC: Fix socrates NAND problemMarek Vasut2011-10-03-35/+35
| | | | | | | | | | | | | | | | | | nand.c:36: error: static declaration of 'nand_read_buf' follows non-static declaration /home/marex/u-boot/include/nand.h:139: error: previous declaration of 'nand_read_buf' was here Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2011-10-04-267/+3451
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-mpc85xx: powerpc/p3060: Add SoC related support for P3060 platform powerpc/85xx: Add support for setting up RAID engine liodns on P5020 powerpc/85xx: Refactor some defines out of corenet_ds.h fm-eth: Add ability for board code to disable a port powerpc/mpc8548: Add workaround for erratum NMG_LBC103 powerpc/mpc8548: Add workaround for erratum NMG_DDR120 powerpc/mpc85xxcds: Fix PCI speed powerpc/mpc8548cds: Fix booting message powerpc/p4080: Add support for secure boot flow powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards powerpc/p2041rdb: remove watch dog related codes powerpc/p2041rdb: updated description of cpld command powerpc/p2041rdb: add more ddr frequencies support powerpc/p2041rdb: set sysclk according to status of physical switch SW1 powerpc/p2041rdb: update cpld reset command according to CPLD 2.0 powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver powerpc/mpc8xxx: Add DDR2 to unified DDR driver powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps() powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en powerpc/85xx: Refactor P2041RDB to use common p_corenet files powerpc/85xx: refactor common P-Series CoreNet files for FSL boards powerpc/85xx: Enable CMD_REGINFO on corenet boards powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries powerpc/85xx: Fix USB protocol definitions for P1020RDB powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM powerpc/mpc8xxx: Move DDR RCW overriding to common code powerpc/mpc8xxx: Extend CWL table powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536 powerpc/85xx: Cleanup extern in corenet_ds board code powerpc/p2041rdb: Add ethernet support on P2041RDB board powerpc/85xx: Add networking support to P1023RDS powerpc/hydra: Add ethernet support on P5020/P3041 DS boards powerpc/85xx: Add FMan ethernet support to P4080DS powerpc/85xx: Add support for FMan ethernet in Independent mode powerpc/mpc8548cds: Cleanup mpc8548cds.c powerpc/mp: add support for discontiguous cores powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries fdt: Add new fdt_create_phandle helper fdt: Rename fdt_create_phandle to fdt_set_phandle powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010) powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC) fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010) powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB nand: Freescale Integrated Flash Controller NAND support powerpc/85xx: Add basic support for P1010RDB powerpc/85xx: Add support for new P102x/P2020 RDB style boards powerpc/85xx: relocate CCSR before creating the initial RAM area powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0 powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
| * powerpc/mpc85xxcds: Fix PCI speedchenhui zhao2011-10-03-12/+12
| | | | | | | | | | | | | | | | The CDS uses PCICLK as SYSCLK. The PCICLK should be 33333333Hz or 66666666Hz. Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com> Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/mpc8548cds: Fix booting messagechenhui zhao2011-10-03-3/+3
| | | | | | | | | | | | Align the output for PCI. Replace "PCI" with "PCI1". Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
| * powerpc/p2041rdb: remove watch dog related codesShaohui Xie2011-10-03-12/+1
| | | | | | | | | | | | | | | | | | | | CPLD 2.2 removed board watch dog support due to the limitation of CPLD capacity after adding all the requested features, such as switch overriding. There is no pin-compatible upgrade part available for current PCB design. So remove codes related to it. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/p2041rdb: updated description of cpld commandShaohui Xie2011-10-03-8/+8
| | | | | | | | | | | | | | | | According to CPLD 2.2, the default configuration is changed, so updated the description of CPLD command, otherwise it will confusing. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/p2041rdb: add more ddr frequencies supportShaohui Xie2011-10-03-1/+4
| | | | | | | | | | | | | | | | | | This table covers DDR frequencies from 666 to 1666. Frequencies 666, 833, 1000, 1066 and 1333 were verified on this board with SO-DIMM (UG51U6400N8SU-ACF). Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/p2041rdb: set sysclk according to status of physical switch SW1Shaohui Xie2011-10-03-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | P2041RDB supports 3 sysclk frequencies, it's selected by SW1[6~8], software need to read the SW1 status to decide what the sysclk needs. SW1[8~6] : frequency 0 0 1 : 83.3MHz 0 1 0 : 100MHz others: 66.667MHz Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/p2041rdb: update cpld reset command according to CPLD 2.0Shaohui Xie2011-10-03-7/+11
| | | | | | | | | | | | | | | | | | CPLD 2.0 provides a new register which bit[0] is set to '1' will reset board with initializing the CPLD registers to default values. And add bit[6] of register at offset 0x5 to use to enable flash bank selection. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driverYork Sun2011-09-29-11/+123
| | | | | | | | | | | | | | | | | | | | Update MPC8349EMDS to use unified DDR driver instead of spd_sdram.c. The unified driver can initialize data using DDR controller. No need to use DMA if just to initialze for ECC. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Refactor P2041RDB to use common p_corenet filesKumar Gala2011-09-29-202/+13
| | | | | | | | | | | | | | | | | | | | | | The P2041RDB has almost identical setup for TLB, LAWS, and PCI with other P-Series CoreNet platforms. The only difference between P2041RDB & P3041DS/P4080DS/P5020DS is the CPLD vs PIXIS FPGA which we can handle via some simple #ifdefs in the TLB and LAW setup tables. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: refactor common P-Series CoreNet files for FSL boardsKumar Gala2011-09-29-5/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We currently support 4 SoC/Boards from the P-Series of QorIQ SoCs that are based on the 'CoreNet' Architecture: P2041RDB, P3041DS, P4080DS, and P5020DS. There is a significant amount of commonality shared between these boards that we can refactor into common code: * Initial LAW setup * Initial TLB setup * PCI setup We start by moving the shared code between P3041DS, P4080DS, and P5020DS into a common directory to be shared with other P-Series CoreNet boards. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entriesKumar Gala2011-09-29-15/+19
| | | | | | | | | | | | | | We shouldn't be setting execute permissions on TLB entries that will not actually have any code run from them. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMMYork Sun2011-09-29-19/+84
| | | | | | | | | | | | | | | | | | | | | | RDIMM has different timing parameters from UDIMM. Create new tables for RDIMMs. Single-, dual- and quad-rank RDIMMs have been verified with speeds from 800 to 1333MT/s. Speed table expands to include 1600MT/s for future use. Single- and quad-rank RDIMM entries are copied into UDIMM tables for future use. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/mpc8xxx: Move DDR RCW overriding to common codeYork Sun2011-09-29-14/+0
| | | | | | | | | | | | | | | | DDR RCW varies at different speeds. It is common for all platform. Move it out from corenet_ds. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Cleanup extern in corenet_ds board codeKumar Gala2011-09-29-2/+1
| | | | | | | | | | | | Move extern of pci_of_setup() into corenet_ds.h Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/p2041rdb: Add ethernet support on P2041RDB boardMingkai Hu2011-09-29-0/+230
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for RGMII, SGMII and XAUI Ethernet on P2041RDB board. The five dTSEC can be routed to two on-board RGMII phy, three on-board SGMII phy or four SGMII phy on SGMII riser card according to different serdes protocol configuration and board lane configuration. Also updated the device tree to direct the Fmac MAC to the correct PHY. Removed CONFIG_SYS_FMAN_FW as its not used anywhere. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add networking support to P1023RDSRoy Zang2011-09-29-0/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The P1023 has two 1G ethernet controllers the first can run in SGMII, RGMII, or RMII. The second can only do SGMII & RGMII. We need to setup a for SoC & board registers based on our various configuration for ethernet to function properly on the board. Removed CONFIG_SYS_FMAN_FW as its not used anywhere. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Lei Xu <B33228@freescale.com> Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com> Signed-off-by: Shaohui Xie <b21989@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/hydra: Add ethernet support on P5020/P3041 DS boardsTimur Tabi2011-09-29-0/+555
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for RGMII, SGMII, and XAUI (10Gb) Ethernet on P3041DS & P5020DS ("Hydra"). The lane_to_slot[] array is initialized dynamically, since board switches can be used to control the muxing of SERDES lanes to slots. The BRDCFG1 PIXIS register is used to route the MII bus to the appropriate slot. The SERDES configuration is queried to help determine the routing between MACs and slot/phy combination. If a XAUI card is inserted, muxing for that card is enabled and never turned off. The PHY address for the 10G XAUI card depends on the slot in which it's inserted. If it's in slot 1, the address is 4. If it's in slot 2, the address is 0. Update the MDIO routing in the P3041DS and P5020DS device trees based on the board-level muxing. The SERDES configuration determines which SGMII/XGMII boards are located in which slots, and so the MDIO bus needs to be muxed correctly whenever talking to a PHY connected to any Fman MAC. The Fman Ethernet nodes in the device tree also need to be routed to the correct PHYs. Removed CONFIG_SYS_FMAN_FW as its not used anywhere. Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add FMan ethernet support to P4080DSAndy Fleming2011-09-29-4/+632
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for RGMII, SGMII, and XAUI (10Gb) Ethernet on P4080DS. The board supports add-on cards for SGMII and XAUI functionality. Which slots on the board these cards are in is a function of the SERDES option selected and muxes on the board. Additionally because of the high-configurablity which MDIO bus one is connected to is "selected" via an FPGA register. We create dummy MDIO bus for the phy layer and hide the mux manipulation in this dummy layer. Add fman fdt helper function in board common code it'll be used by several freescale boards that do various muxing of the MDIO signals based on which controller/interface one is trying to talk to. Removed CONFIG_SYS_FMAN_FW as its not used anywhere. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/mpc8548cds: Cleanup mpc8548cds.cZhao Chenhui2011-09-29-7/+0
| | | | | | | | | | | | | | Remove unnecessary or dead code/includes. Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entriesKumar Gala2011-09-29-15/+15
| | | | | | | | | | | | | | We shouldn't be setting execute permissions on TLB entries that will not actually have any code run from them. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add basic support for P1010RDBPoonam Aggrwal2011-09-29-0/+765
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot methods supported: NOR Flash, SPI Flash and SDCARD This patch adds the following basic interfaces: DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash. P1010RDB Overview ----------------- 1Gbyte DDR3 (on board DDR) Local Bus (IFC): 32Mbyte 16bit NOR flash 32Mbyte SLC NAND Flash 64KB CPLD device(GPCM interface) SPI Flash: 128 Mbit SPI Flash memory SD/MMC: connector to interface with the SD memory card SATA: 1 internal SATA connect to 2.5. 160G SATA2 HDD 1 eSATA connector to rear panel USB 2.0: x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface. x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet eTSEC: eTSEC1: Connected to RGMII PHY VSC8641XKO eTSEC2: Connected to SGMII PHY VSC8221 eTSEC3: Connected to SGMII PHY VSC8221 eCAN: Two DB-9 female connectors for Field bus interface UART: supports two UARTs up to 115200 bps for console TDM: 2 FXS ports connected via an external SLIC to the TDM interface. SLIC: SPI SLIC I2C: Serial EEprom Real time clock 256 Kbit M24256 I2C EEPROM PCIe: PCIe and mPCIe connectors. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add support for new P102x/P2020 RDB style boardsLi Yang2011-09-29-0/+946
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following boards share a common design but with minor variations between them: P1020MSBG-PC P1020RDB-PC P1020UTM-PC P1021RDB-PC P1024RDB P1025RDB P2020RDB-PC The P1020RDB-PC shares its roots in the existing P1020RDB board design, however uses DDR3 instead of DDR2. P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK. Key features on these boards include: * DDR3 * NOR flash * NAND flash (on RDB's only) * SPI flash (on RDB's only) * SDHC/MMC card slot * VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB) * PCIE slot and mini-PCIE slots As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM is used to store SPD data. In case of absent or corrupted SPD, falling back to timing data embedded in the source code will be used. Raw timing data is extracted from DDR chip datasheet. Different speeds of DDR are supported with this approach. ODT option is forced to fit this set of boards, again because they don't have regular DIMMs. CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet specification for writing timing. VSC firmware Address is defined by default in config file for eTSEC1. SD width is based off DIP switch. DIP switch is detected on the board by reading i2c bus and setting the appropriate mux values. Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC have pins multiplexing. QE function needs to be disabled to access Nor Flash and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe" in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below 'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD. 'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Zhao Chenhui <b26998@freescale.com> Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Tang Yuantian <b29983@freescale.com> Signed-off-by: ramneek.mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>
* | sbc82xx: delete support for obsolete SBC8240/SBC8260Paul Gortmaker2011-10-01-1664/+0
| | | | | | | | | | | | | | | | | | | | The EST SBC8260 is over 10 years old, and the SBC8240 older than that. With the tiny amount of RAM (by today's standards), there really isn't anyone interested in running the latest U-boot on these EOL products anymore. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> CC: jon.diekema@smiths-aerospace.com
* | Merge branch 'post' of git://git.denx.de/u-boot-blackfinWolfgang Denk2011-10-01-237/+2
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'post' of git://git.denx.de/u-boot-blackfin: Blackfin: uart: implement loop callback for post Blackfin: bf537-stamp/bf548-ezkit: update POST flash block range Blackfin: post: generalize led/button tests with GPIOs Blackfin: bf537-stamp: drop uart/flash post tests Blackfin: post: drop custom test list Blackfin: bf537-stamp: convert to gpio post hotkey
| * | Blackfin: post: generalize led/button tests with GPIOsMike Frysinger2011-09-29-88/+1
| | | | | | | | | | | | | | | | | | Make it easy for any Blackfin board to enable led/push button tests. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | Blackfin: bf537-stamp: drop uart/flash post testsMike Frysinger2011-09-29-54/+0
| | | | | | | | | | | | | | | | | | | | | The flash code has been generalized for everyone, and the uart stub is simply useless. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | Blackfin: bf537-stamp: convert to gpio post hotkeyMike Frysinger2011-09-29-95/+1
| |/ | | | | | | | | | | | | No need for our custom implementations now that common code supports the generic gpio layer. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | EfikaSB: Add preliminary EfikaSB supportMarek Vasut2011-09-30-25/+99
| | | | | | | | | | Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
* | EfikaMX: Add imximage config for Efika SBMarek Vasut2011-09-30-0/+122
| | | | | | | | | | Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
* | vision2: Place machine ID into board configFabio Estevam2011-09-30-1/+0
| | | | | | | | | | | | | | | | Let common code set the machine ID. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* | zmx25: Place machine ID into board configFabio Estevam2011-09-30-2/+0
| | | | | | | | | | | | | | Let common code set the machine ID. Cc: Matthias Weisser <weisserm@arcor.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | zmx25: Remove dram_init_banksize()Fabio Estevam2011-09-30-6/+0
| | | | | | | | | | | | | | | | As only one RAM bank is used we can rely on the code from arch/arm/lib/board.c Cc: Matthias Weisser <weisserm@arcor.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* | mx53evk: Place machine ID into board configFabio Estevam2011-09-30-1/+0
| | | | | | | | | | | | | | | | Let common code set the machine ID. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
* | mx53ard: Place machine ID into board configFabio Estevam2011-09-30-1/+0
| | | | | | | | | | | | Let common code set the machine ID. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | mx53smd: Place machine ID into board configFabio Estevam2011-09-30-1/+0
| | | | | | | | | | | | Let common code set the machine ID. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | mx53loco: Place machine ID into board configFabio Estevam2011-09-30-1/+0
| | | | | | | | | | | | | | Let common code set the machine ID. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <jason.hui@linaro.org>
* | mx51evk: Place machine ID into board configFabio Estevam2011-09-30-1/+0
| | | | | | | | | | | | Let common code set the machine ID. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | imx31_litekit: Place machine ID into board configFabio Estevam2011-09-30-1/+0
| | | | | | | | | | | | Let common code set the machine ID. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | mx31ads: Place machine ID into board configFabio Estevam2011-09-30-1/+0
| | | | | | | | | | | | Let common code set the machine ID. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | mx25pdk: Place machine ID into board configFabio Estevam2011-09-30-1/+0
| | | | | | | | | | | | Let common code set the machine ID. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | mx31pdk: Place machine ID into board configFabio Estevam2011-09-30-1/+0
| | | | | | | | | | | | Let common code set the machine ID. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | imx31_litekit: Remove dram_init_banksize()Fabio Estevam2011-09-30-6/+0
| | | | | | | | | | | | As only one RAM bank is used we can rely on the code from arch/arm/lib/board.c Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | mx31ads: Remove dram_init_banksize()Fabio Estevam2011-09-30-6/+0
| | | | | | | | | | | | As only one RAM bank is used we can rely on the code from arch/arm/lib/board.c Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | mx25pdk: Remove dram_init_banksize()Fabio Estevam2011-09-30-6/+0
| | | | | | | | | | | | As only one RAM bank is used we can rely on the code from arch/arm/lib/board.c Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | mx31pdk: Remove dram_init_banksize()Fabio Estevam2011-09-30-6/+0
| | | | | | | | | | | | As only one RAM bank is used we can rely on the code from arch/arm/lib/board.c Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
generated by cgit v1.1 at 2024-12-26 08:15:10 +0000