| Commit message (Collapse) | Author | Age | Lines |
|---|
| |
|
|
|
|
|
| |
Remove userbutton command and do the detection in board config file using the gpio command
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* 'master' of git://git.denx.de/u-boot-net:
net/designware: Change timeout loop implementation
net/designware: Set ANAR to 0x1e1
net/designware: Program phy registers when auto-negotiation is ON
net/designware: Try configuring phy on each dw_eth_init
net/designware: Consecutive writes must have delay
net/designware: Phy address fix
net/designware: Fix the max frame length size
net/designware: Fix to restore hw mac address
microblaze: Wire up LL_TEMAC driver initialization
microblaze: Add faked LL_TEMAC driver configuration
microblaze: Enable several ethernet driver compilation
net: ll_temac: Add LL TEMAC driver to u-boot
Update net subsystem maintainer in doc/git-mailrc
net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall back
mvgbe: remove warning for unused methods
|
| | |
| |
| |
| |
| |
| |
| | |
Initialize ll_temac driver.
Reported-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Stephan Linz <linz@li-pro.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Expand the specific configuration for the microblaze-generic
board in xparameters.h with a faked setup to enable the
LL_TEMAC driver.
Note: From now the microblaze-generic board is no longer a
valid board configuration for a real piece of hardware. Rather
than, we use the file config.mk and xparameters.h as a faked
board configuration to force the compilation of all potential
driver code for Microblaze systems.
Signed-off-by: Stephan Linz <linz@li-pro.net>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
* 'master' of git://git.denx.de/u-boot-onenand:
onenand: samsung: Enable OneNAND support at Samsung's Exynos4210
onenand: Replace ONENAND_IS_MLC() with ONENAND_HAS_4KB()
onenand:samsung OneNAND chip probe functions added for GONI and Exynos4210
onenand:samsung Target dependent OneNAND chip probe function
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Separate callback for probing OneNAND memory chip.
Tested at:
Samsung S5PC110 GONI
Samsung Exynos4210 (S5PC210 Universal)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
|
| |/
|
|
|
|
|
| |
This avoids a compiler warning about unused variables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-By: Graeme Russ <graeme.russ@gmail.com>
|
| |
|
|
|
|
|
|
| |
two boards were redeclaring pciauto_region_allocate() in their local
scope for no obvious reason, the function is in <pci.h> anyway,
this is probably just copying artifacts and old cruft.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
lzma: fix printf warnings
Remove CONFIG_SYS_EXTBDINFO from snapper9260.h
cmd_pxe.c: fix strict-aliasing warnings
net: smc91111: use mdelay()
doc: Fix some typos in different files
disk/part.c: Fix device enumeration through API
mkenvimage: Really set the redundant byte when applicable
mkenvimage: Don't try to detect comments in the input file
mkenvimage: Use mmap() when reading from a regular file
mkenvimage: Read/Write from/to stdin/out by default or if the filename is "-"
mkenvimage: More error handling
mkenvimage: Correct an include and add a missing one
mkenvimage: correct and clarify comments and error messages
MAKEALL: display SPL size if present
ARMV7/Vexpress: add missing get_ticks() and get_tbclk()
mkenvimage: fix usage message
cmd_fat: add FAT write command
fs/fat/fat_write.c: Fix GCC 4.6 warnings
FAT write: Fix compile errors
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
commit f31a911fe (arm, post: add missing post_time_ms for arm)
enables get_ticks and get_tbclk for all arm based boards,
arm/vexpress also needs these functions to work.
Signed-off-by: Liming Wang <walimisdev@gmail.com>
Acked-by: Matt.Waddel@linaro.org
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
* 'master' of git://git.denx.de/u-boot-arm: (146 commits)
arm: Use common .lds file where possible
arm: add a common .lds link script
arm: Remove unneeded setting of LDCSRIPT
Define CPUDIR for the .lds link script
arm: Remove zipitz2 link script
Allow arch directory to contain .lds without requiring Makefile
OMAP: Remove omap1610inn-based boards
arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix build warnings
board/ti/beagle/beagle.c: Fix build warnings
sdrc.c: Fix typo in do_sdrc_init() for SPL
tegra: i2c: Add I2C driver
tegra: fdt: i2c: Add extra I2C bindings for U-Boot
tegra: i2c: Select I2C ordering for Seaboard
tegra: i2c: Enable I2C on Seaboard
tegra: i2c: Select number of controllers for Tegra2 boards
tegra: i2c: Initialise I2C on Nvidia boards
tegra: Enhance clock support to handle 16-bit clock divisors
fdt: Add function to allow aliases to refer to multiple nodes
tegra: Rename NV_PA_PMC_BASE to TEGRA2_PMC_BASE
tegra: fdt: Enable FDT support for Ventana
tegra: fdt: Enable FDT support for Seaboard
tegra: usb: Enable USB on Seaboard
tegra: usb: Add common USB defines for tegra2 boards
tegra: usb: Add USB support to nvidia boards
arm: Check for valid FDT after console is up
fdt: Avoid early panic() when there is no FDT present
tegra: usb: Add support for Tegra USB peripheral
tegra: fdt: Add function to return peripheral/clock ID
usb: Add support for txfifo threshold
tegra: usb: fdt: Add USB definitions for Tegra2 Seaboard
tegra: usb: fdt: Add additional device tree definitions for USB ports
tegra: fdt: Add clock bindings for Tegra2 Seaboard
tegra: fdt: Add clock bindings
tegra: fdt: Add additional USB binding
fdt: Add tegra-usb bindings file from linux
fdt: Add staging area for device tree binding documentation
tegra: fdt: Add device tree file for Tegra2 Seaboard from kernel
tegra: fdt: Add Tegra2x device tree file from kernel
arm: fdt: Add skeleton device tree file from kernel
fdt: Add basic support for decoding GPIO definitions
fdt: Add functions to access phandles, arrays and bools
fdt: Tidy up a few fdtdec problems
fdt: Add tests for fdtdec
fdt: Add fdtdec_find_aliases() to deal with alias nodes
arm: Tegra2: Fix ELDK42 gcc failure with inline asm stack pointer load
net: fec_mxc: allow use with cache enabled
net: force PKTALIGN to ARCH_DMA_MINALIGN
i.MX28: Enable caches by default
i.MX28: Make use of the bounce buffer
i.MX28: Do data transfers via DMA in MMC driver
MMC: Implement generic bounce buffer
i.MX28: Add cache support to MXS NAND driver
i.MX28: Add cache support into the APBH DMA driver
ARM926EJS: Implement cache operations
board/vpac270/onenand.c: Fix build errors
nhk8815: fix build errors
atmel-boards: add missing atmel_mci.h
ARM: highbank: setup env from boot source register
ARM: highbank: change env config to use nvram
ARM: highbank: add reset support
ARM: highbank: Add boot counter support
ARM: highbank: change TEXT_BASE to 0x8000
ARM: highbank: fix us_to_tick calculation
ARM: highbank: add missing get_tbclk
ARM: highbank: fix warning for calxedaxgmac_initialize
net: calxedaxgmac: fix build due to missing __aligned definition
EXYNOS: Add structure for Exynos4 DMC
EXYNOS: SMDK5250: Support all 4 UARTs
ARM: fix s3c2410 timer code
ARM: davinci: fixes for cam_enc_4xx board
omap3_spi: receive transmit mode
calimain, enbw_cmc: Fix typo in comments
Davinci: ea20: use gpio framework to access gpios
OMAP3: mt_ventoux: sets its own mtdparts
OMAP3: mt_ventoux: updated timing for FPGA
twl4030: fix potential power supply handling issues
NAND: TI: fix warnings in omap_gpmc.c
cam_enc_4xx: Rename 'images' to 'imgs'
arm: Add Prep subcommand support to bootm
OMAP3: twister: add support to boot Linux from SPL
SPL: call cleanup_before_linux() before booting Linux
OMAP3: SPL: do not call I2C init if no I2C is set.
Add cache functions to SPL for armv7
devkit8000: Implement and activate direct OS boot
omap/spl: change output of spl_parse_image_header
omap-common/spl: Add linux boot to SPL
devkit8000/spl: init GPMC for dm9000 in SPL
omap-common: Add NAND SPL linux booting
devkit8000: add config for spl command
Add cmd_spl command
mx53ard: Initialize return code with error
mx53: Make PLL2 to be the parent of UART clock
configs: imx: Use CONFIG_SF_DEFAULT_CS
mx28evk: Provide default values for SPI bus and chip select
USB: ehci-mx6: Add proper IO accessors
mx6: Read silicon revision from register
i.MX28: Drop __naked function from spl_mem_init
mxs_spi: Return proper timeout error
i.MX28: Make the stabilization delays shorter
pmic_i2c: Return error in case of invalid pmic_i2c_tx_num
mx6: Remove duplicate definition of ANATOP_BASE_ADDR
mx6: Fix reset cause for Power On Reset case
i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITE
i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG
i.MX28: Enable additional DRAM address bits
mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use for environment
mx31: add "ARM11P power gating" to get_reset_cause
mx31pdk: Fix CONFIG_SYS_MEMTEST_END
efikamx: Fix CONFIG_SYS_MEMTEST_END
mx53smd: Fix CONFIG_SYS_MEMTEST_END
mx53evk: Fix CONFIG_SYS_MEMTEST_END
mx51evk: Fix CONFIG_SYS_MEMTEST_END
i.MX6: mx6qsabrelite: add ext2 support
imximage: Remove overwriting of flash_offset
IXP: Fix GPIO_INT_ACT_LOW_SET()
IXP: Fix NAND build warning on PDNB3 and SCPU
IXP: Move PDNB3 and SCPU from Makefile to boards.cfg
IXP: Squash warnings in IXP NPE
IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST}
IXP: Make IXP buildable with arm-linux- toolchains
Examples: Properly append LDFLAGS to LD command
SPL: Enable YMODEM support on BeagleBone and AM335x EVM
SPL: Add YMODEM over UART load support
SPL: Add README.omap3
README: document more SPL config options
spl.c: Use __noreturn decorator
config.mk: Check for -fstack-usage support
config.mk: Make cc-option create a file under include/generated
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
This link script doesn't appear to do anything useful or unique, so
drop it, and rely on the CPU one.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The CS_AUTOBOOT configurations have been broken for a long time.
Kshitij Gupta is no longer at TI making these broken and orphaned
boards, so remove.
Signed-off-by: Tom Rini <trini@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fix:
beagle.c:257:13: warning: function declaration isn't a prototype
[-Wstrict-prototypes]
beagle.c:257:13: warning: function declaration isn't a prototype
[-Wstrict-prototypes]
Also make beagle_dvi_pup() checkpatch clean, fix:
ERROR: open brace '{' following function declarations go on the
next line
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Select the port ordering for I2C on Seaboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This enables I2C on all Nvidia boards including Seaboard and
Harmony.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This adds basic USB support for port 0. The other port is not supported
yet.
Tegra2 (SeaBoard) # usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 5 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Tegra2 (SeaBoard) # ext2load usb 0:3 10000000 /boot/vmlinuz
Loading file "/boot/vmlinuz" from usb device 0:3 (ROOT-A)
2932976 bytes read
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
We set up two USB ports, one of which can be host or device.
For some reason the kernel version does enable both ports.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add the definition of the oscillator clock frequency and the 32KHz clock.
The latter is provided by a PMIC on I2C which we don't actually use at
present, but we expect this definition to be used in the kernel and want
to keep our .dts the same.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This was taken from commit b48c54e2 at:
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Building for vpac270_ond_256 configuration fails:
arch/arm/lib/libarm.o: In function `icache_disable':
/home/ag/git/u-boot/arch/arm/lib/cache-cp15.c:156: multiple
definition of `icache_disable'
board/vpac270/libvpac270.o:/home/ag/git/u-boot/board/vpac270/onenand.c:65:
first defined here
arch/arm/lib/libarm.o: In function `dcache_disable':
/home/ag/git/u-boot/arch/arm/lib/cache-cp15.c:188: multiple
definition of `dcache_disable'
board/vpac270/libvpac270.o:/home/ag/git/u-boot/board/vpac270/onenand.c:66:
first defined here
make[1]: *** [/home/ag/git/u-boot/spl/u-boot-spl] Error 1
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
commit 72fa467988e7944407a634ddc4bc6a2df685c04c moved atmel_mci_init() into
include/atmel_mci.h. Some AT91 boards are also using this interface and need
to include atmel_mci.h now.
This patch fixes MAKEALL complaints like this:
---8<---
Configuring for ethernut5 - Board: ethernut5, Options: AT91SAM9XE
ethernut5.c: In function 'board_mmc_init':
ethernut5.c:235:2: warning: implicit declaration of function 'atmel_mci_init' [-Wimplicit-function-declaration]
--->8---
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Reinhard Meyer <u-boot@emk-elektronik.de>
CC: egnite GmbH <info@egnite.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add support to read the boot src register and set bootcmd env from the
selected bootcmdX env setting.
Based on Linkstation boot choice selection.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Implement reset for highbank platform. Reset is triggered via a wfi
instruction, so enabling armv7 for the compiler is necessary.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
| | | |
| | |
| | |
| | |
| | |
| | | |
Add boot counter support using an sysreg which is persistent across reset.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
| | | |
| | |
| | |
| | |
| | |
| | | |
Add include of netdev.h to pick-up declaration of calxedaxgmac_initialize.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This properly configures the mux to enable all UARTs.
This also fixes things so that we don't configure balls XUCTSN_1 and
XURTSN_1 as UART1 configuration (RTS/CTS), since they aren't
connected.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Chander kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
- change CONFIG_ENV_RANGE to contain 2 nand erase blocks,
one for bad block reserve.
- remove from the envvariable "img_writeramdisk" the
ubifsmount command, as it is not needed.
- erase the hole mtd partition containing u-boot
- save environment variable "dvn_app_vers" and "dvn_boot_vers"
only after installing the new image.
changes requested from Marek Vasut:
- arm, davinci: fix eldk-4.2 warnings for cam_enc_4xx board
- get rid of run_command2 usage
needed since patch:
commit 009dde1955583e306cf904c864068f3acb0db499
Author: Simon Glass <sjg@chromium.org>
Date: Tue Feb 14 19:59:20 2012 +0000
Rename run_command2() to run_command()
is now in mainline.
- add CONFIG_SPL_LIBGENERIC_SUPPORT support
- remove CONFIG_CMD_PXE support
- fix warning:
cam_enc_4xx.c: In function 'menu_handle':
cam_enc_4xx.c:609: warning: dereferencing type-punned pointer
will break strict-aliasing rules
- fix error:
arm-linux-ld: u-boot-spl: Not enough room for program headers,
try linking with -N
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Fletzer Martin <Martin.Fletzer@ait.ac.at>
Cc: Wolfgang Denk <wd@denx.de>
|
| | | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Drop direct access to SOC's registers and use
the function of the GPIO driver for da8xx.
[Tom: Remove gpio[68]_base as it's now unused]
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Bastian Ruppert <Bastian.Ruppert@Sewerin.de>
CC: dzu@denx.de
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fix chipselect timing for FPGA
Signed-off-by: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
To avoid a conflict with common/cmd_bootm.c's 'images' (which is
exposed as part of the Linux SPL series), rename the board-specific
'images' to 'imgs'.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
- Implements spl_start_uboot() for devkit8000
- Add configs to activate direct OS boot from SPL
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Linux crashes if the GPMC isn't configured for the dm9000.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The variable "rc" is the return of board_eth_init() function. Initialize
it with an error code, so that this function can return an error when
CONFIG_SMC911X is not set.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This is needed to support Freescale-supplied userspaces.
At the moment, both the IPU and VPU libraries provided by Freescale
in the "imx-lib" package contain routines which scrape the system
revision from /proc/cpuinfo. In the VPU library, this information is
used to load the proper firmware, allowing a single binary to be used
across various i.MX processors.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
|
| | | |
| | |
| | |
| | |
| | |
| | | |
for environment
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
nand.c: In function ‘pdnb3_nand_read_buf’:
nand.c:107:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
nand.c: In function ‘pdnb3_nand_dev_ready’:
nand.c:124:18: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
Remove the 4-byte-at-time read mode altogether, the most is bogus and will
likely cause unaligned accesses.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
These symbols are no longer defined in Linux-ARM's mach-types files. Replace
these with CONFIG_MACH_TYPE instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
This prototype version SoM is unused and not available to public.
Support this only for internal debugging purposes.
Signed-off-by: Marek Vasut <marex@denx.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The LCD pins configuration was wrong in U-Boot, configure pins properly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
|
| | | |
| | |
| | |
| | |
| | |
| | | |
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Configuring for zipitz2 board...
zipitz2.c: In function ‘board_mmc_init’:
zipitz2.c:85:2: warning: implicit declaration of function ‘pxa_mmc_register’ [-Wimplicit-function-declaration]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This link script seems old and incompatible with relocation and its
own sa1000 start.S file. It isn't used because the CPU's link script
was picked up in preference to this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
|
| | |/
| |
| |
| | |
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Build error was with board/renesas/ecovec/lowlevel_init.S
include/version.h: Assembler messages:
include/version.h:41: Error: unknown opcode
lowlevel_init.S:48: Error: unknown opcode
lowlevel_init.S:51: Error: unknown opcode
etc
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
| | |
| |
| |
| | |
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
| | |
| |
| |
| | |
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
| |/
|
|
|
|
|
| |
The sh7757lcr has 2GByte eMMC chip. This patch supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
