summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
* Merge git://git.denx.de/u-boot-mpc85xxTom Rini2014-12-08-70/+3877
|\
| * powerpc/hydra: fix judging condition of RGMII selectionMinghuan Lian2014-12-05-1/+2
| | | | | | | | | | | | | | | | | | | | BRDCFG1_EMI1_SEL_MASK has been changed to 0x78, which contains selection bits and connected status bit. So the Corresponding mux value of RGMII is changed to BRDCFG1_EMI1_SEL_RGMII | BRDCFG1_EMI1_EN. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/hydra: Update MDIO mux fixupsChunhe Lan2014-12-05-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | The new device trees use a more generic interface for supporting muxing mdio buses. The mux property is thus specified in "reg", rather than "fsl,hydra-mdio-muxval". In order to support using old device trees, we keep the old fixup in there. Linux will therefore see the both properties, but will ignore fsl,hydra-mdio-muxval. Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * board/t1024qds: add retimer support on t1024qdsShengzhou Liu2014-12-05-0/+57
| | | | | | | | | | | | | | Initialize retimer for XFI on t1024qds. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * t1024qds: increase IO drive strengthShengzhou Liu2014-12-05-0/+4
| | | | | | | | | | | | | | | | Increase IO drive strength to fix FCS error on RGMII ports on T1024QDS. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * board/t1024qds: update pin multiplexingShengzhou Liu2014-12-05-2/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | Add multiplexing support among SPI flash, TDM riser card and SDXC. it routes SPI pins to SPI flash by default. Route SPI pins to SD slot if "adaptor=sdxc" is set in hwconfig. Route SPI pins to TDM riser card and do fixup for dts if "pin_mux=tdm" is set in hwconfig. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/t1024rdb: Add T1024 RDB board supportShengzhou Liu2014-12-05-0/+1169
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC. T1024RDB board Overview ----------------------- - T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support - Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC - Ethernet interfaces: - Two 10M/100M/1G RGMII ports on-board - one 10Gbps XFI interface - PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors. - SerDes: 4 lanes up to 10.3125GHz - IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD - eSPI: 64MB N25Q512 SPI flash. - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) - USB: Two Type-A USB2.0 ports with internal PHY - eSDHC: Support SD, SDHC, SDXC and MMC/eMMC - I2C: Four I2C controllers - UART: Two UART serial ports Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT Fix Kconfig by adding SUPPORT_SPL] Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/t1024qds: Add T1024 QDS board supportShengzhou Liu2014-12-05-0/+1736
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1024QDS is a high-performance computing evaluation, development and test platform for T1024 QorIQ Power Architecture processor. T1024QDS board Overview ----------------------- - T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC - Ethernet interfaces: - Two 10M/100M/1G RGMII ports on-board - Three 1G/2.5Gbps SGMII ports - Four 1Gbps QSGMII ports - one 10Gbps XFI or 10Base-KR interface - SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora - PCIe: Three PCI Express controllers with five PCIe slots. - IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA - Video: DIU supports video up to 1280x1024x32 bpp. - Chrontel CH7201 for HDMI connection. - TI DS90C387R for direct LCD connection. - Raw (not encoded) video connector for testing or other encoders. - QUICC Engine block - 32-bit RISC controller for flexible support of the communications peripherals - Serial DMA channel for receive and transmit on all serial channels - Two universal communication controllers, supporting TDM, HDLC, and UART - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) - eSPI: Three SPI flash devices. - SATA: one SATA 2.O. - USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB) - eSDHC: Support SD, SDHC, SDXC and MMC/eMMC. - I2C: Four I2C controllers. - UART: Two UART on board. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT Fix Kconfig by adding SUPPORT_SPL] Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/t2080: updating rcw for silicon v1.1Shengzhou Liu2014-12-05-10/+26
| | | | | | | | | | | | | | | | | | T2080 v1.1 requires different MEM_PLL_RAT from previous v1.0, and also update core frequency to 1.8GHz for v1.1. We reserve the support for T2080 v1.0 and enable v1.1 by default. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * B4860QDS: Enable enet port as per fsl_b4860_serdes2 string in hwconfigSuresh Gupta2014-12-05-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp respectively in hwconfig. Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/b4860qds: add workaround for XFIShaohui Xie2014-12-05-0/+125
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | XFI does not work stable on current board, it's due to heat sink issue, to make it work stable the board needs additional heat sink, enable two XFI lanes only. Right now we do not have such an erratum for the issue, so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it. The workaround will only be used in XFI protocols and only if the hwconfig indicates that XFI is prefered. A new VSC3308 config function is used instead of re-use the original function, to avoid making the function complex and ugly. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * B4860QDS: Enable SFP or AMC on basis of hwconfig stringSuresh Gupta2014-12-05-8/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | SerDes2 lanes EFGH either go to SFP or AMC riser card slot2. By default AMC will be configured even if no hwconfig is specified. To enable XFI via SFP use the below hwconfig: fsl_b4860_serdes2:sfp_amc=sfp Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@ffeescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/b4860qds: dtb fixup for xfiShaohui Xie2014-12-05-0/+38
| | | | | | | | | | | | | | | | Since xfi has no phy, we delete the property "phy-handle" and use a "fixed-link" property for a xfi port. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/b4860qds: add xfi supportShaohui Xie2014-12-05-7/+39
| | | | | | | | | | | | | | | | | | | | We need following changes to make xfi work on B4: 1. set cross-point switch VSC3308 to use sfp config when running xfi; 2. add 10G interface check for xfi; 3. set phy address for xfi so the 10G ports can be registered by mdio; Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * B4860: Add alternate LC VCO serdes protocols support in board fileShaveta Leekha2014-12-05-0/+13
| | | | | | | | | | | | | | | | | | Add the support of newly added LC VCO SerDes protocols for configuration of IDT and VSC crossbar Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * B4860QDS: SGMII related updatesShaveta Leekha2014-12-05-26/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | - Enable SGMII support for 0x8d Serdes 2 protocol. - Correct Phy address for DTSECx for 0x8d/0xb2 Serdes 2 protocol. - Updated debug statement - Add Alternate LC VCO protocols(0x8d-->0x8c, 0xb2-->0xb1) - Rename onboard PHY address defines for more readability - Add these new Defines in B4860QDS.h file Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/b4860: Enable law creation of MAPLEShaveta Leekha2014-12-05-3/+8
| | | | | | | | | | | | | | | | | | B4860, B4440, B4420 and B4220 have MAPLE, so enable law creation for them only. Remove static LAW creation for MAPLE. Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc, muas3001: remove CONFIG_SYS_RAMBOOTHeiko Schocher2014-12-05-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | cppcheck reports: [board/muas3001/muas3001.c:270]: (error) Uninitialized variable: psize remove the CONFIG_SYS_RAMBOOT define to prevent this error report. Signed-off-by: Heiko Schocher <hs@denx.de> Reported-by: Wolfgang Denk <wd@denx.de> Reviewed-by: York Sun <yorksun@freescale.com>
| * km/km82xx: remove CONFIG_SYS_RAMBOOTHolger Brunck2014-12-05-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | This define is never set in our setup, so we can remove it safely. The former code causes cppcheck to complain about: [board/keymile/km82xx/km82xx.c:311]: (error) Uninitialized variable: psize Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Wolfgang Denk <wd@denx.de> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/t208xqds: VID supportYing Zhang2014-12-05-0/+525
| | | | | | | | | | | | | | | | | | | | | | | | The fuse status register provides the values from on-chip voltage ID efuses programmed at the factory. These values define the voltage requirements for the chip. u-boot reads FUSESR and translates the values into the appropriate commands to set the voltage output value of an external voltage regulator. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * board/t104xrdb: Conditional workaround of errata A-008044Prabhakar Kushwaha2014-12-05-8/+14
| | | | | | | | | | | | | | | | | | | | Workaround of Errata A-008044 was implemented without errata number and it is enabled by default. Errata A-008044 is only valid for T1040 Rev 1.0. So put errata number and make it conditional. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/mpc85xx:Put errata number for T104x NAND boot issuePrabhakar Kushwaha2014-12-05-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | When device is configured to load RCW from NAND flash IFC_A[16:31] are driven low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using IFC_A[16:31] lines are not accessible. Workaround is already in-place. Put the errata number to adhere errata handling framework. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * mpc85xx/t208xqds: Adjust DDR timing parametersYork Sun2014-12-05-8/+7
| | | | | | | | | | | | | | | | | | | | | | Adjust timing for dual-rank UDIMM, verified on M3CQ-8GHS3C0E for speed of 1066, 1333, 1600, 1866MT/s. The 1866 timing is copied to 2133 timing in case such DIMM comes available. Also update single-rank 1866 timing. Enable interactive debugging as well. Signed-off-by: York Sun <yorksun@freescale.com> CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-tiTom Rini2014-12-08-40/+671
|\ \
| * | arm, am335x: siemens boards add FIT supportHeiko Schocher2014-12-04-19/+75
| | | | | | | | | | | | | | | | | | | | | | | | add FIT support and set "boardid" from factoryset records "DEV/id" and "COMP/ver". "boardid" is used for selecting which fit configuration gets booted on the board. Signed-off-by: Heiko Schocher <hs@denx.de>
| * | arm, am335x, siemens: read COMP/ver from factorysetHeiko Schocher2014-12-04-0/+11
| | | | | | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de>
| * | arm, am335x, siemens: fix factoryset interpretationHeiko Schocher2014-12-04-8/+18
| | | | | | | | | | | | | | | | | | | | | | | | a record could contain other records, so after an ">" (begin mark) there not always come an end mark "<", instead a ">" is possible. Take care of this. Signed-off-by: Heiko Schocher <hs@denx.de>
| * | ARM: OMAP5: DRA7xx: Fix misleading comments in mux_data.hLubomir Popov2014-12-04-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The comments on the QSPI pad assignments erronously swapped the qspi1_d0 and qspi1_d1 functionality and could cause confusion. QSPI1_D[0] is in fact muxed on pad U1 (gpmc_a16), and QSPI1_D[1] - on pad P3 (gpmc_a17). Fixing comments. Signed-off-by: Lubomir Popov <l-popov@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
| * | omap_hsmmc: Board-specific TWL4030 MMC power initializationsPaul Kocialkowski2014-12-04-0/+96
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boards using the TWL4030 regulator may not all use the LDOs the same way (e.g. MMC2 power can be controlled by another LDO than VMMC2). This delegates TWL4030 MMC power initializations to board-specific functions, that may still call twl4030_power_mmc_init for the default behavior. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@ti.com> [trini: Fix omap3_evm warning, add twl4030.h] Signed-off-by: Tom Rini <trini@ti.com>
| * | beagle_x15: add board support for Beagle x15Felipe Balbi2014-12-04-0/+470
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BeagleBoard-X15 is the next generation Open Source Hardware BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHZ A15 processor. The platform features 2GB DDR3L (w/dual 32bit busses), eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60), separate LCD port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G Ethernet. For more information, refer to: http://www.elinux.org/Beagleboard:BeagleBoard-X15 Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
| * | arm: omap5: don't enable misc_init_r by defaultFelipe Balbi2014-12-04-12/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Out of all OMAP5-like boards, only one of them needs CONFIG_MISC_INIT_R, so it's best to enable that for that particular board only, instead of enabling for all boards unconditionally. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* | | powerpc: mpc8xx: remove hermes board supportMasahiro Yamada2014-12-08-1266/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This board sprinkles #ifdef(CONFIG_HERMES) over various global files such as include/common.h, common/board_r.c, common/cmd_bdinfo.c. Let's zap such an ill-behaved board. It has not been converted to generic board yet and mpc8xx is old enough. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Wolfgang Denk <wd@denx.de>
* | | ARM: rpi: rename rpi_b to rpiStephen Warren2014-12-08-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | The U-Boot port runs on a variety of RPi models, not just the B. So, rename the port to something slightly more generic. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* | | ARM: rpi_b: detect board revisionStephen Warren2014-12-08-3/+119
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Detect the board revision early during boot, and print the decoded model name. Eventually, this information can be used for tasks such as: - Allowing/preventing USB device mode; some models have a USB device on- board so only host mode makes sense. Others connect the SoC directly to the USB connector, so device-mode might make sense. - The on-board USB hub/Ethernet requires different GPIOs to enable it, although luckily the default appears to be fine so far. - The compute module contains an on-board eMMC device, so we could store the environment there. Other models use an SD card and so don't support saving the environment (unless we store it in a file on the FAT boot partition...) Set $fdtfile based on this information. At present, the mainline Linux kernel doesn't contain a separate DTB for most models, but I hope that will change soon. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* | Merge git://git.denx.de/u-boot-x86Tom Rini2014-12-01-4/+3
|\ \ | |/ |/|
| * x86: chromebook_link: Enable the Chrome OS ECSimon Glass2014-11-25-0/+4
| | | | | | | | | | | | Enable the Chrome OS EC so that it can be used from U-Boot. Signed-off-by: Simon Glass <sjg@chromium.org>
| * x86: Remove board_early_init_r()Simon Glass2014-11-25-5/+0
| | | | | | | | | | | | | | | | This function is not needed. Remove it to improve the generic init sequence slightly. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2014-11-26-9/+36
|\ \
| * | arm: ls102xa: Select ge2_clk125 for eTSEC clock muxingAlison Wang2014-11-24-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EC1 pins in RCW can be selected as RGMII1, GPIO3, CAN1/2, FTM1 or SAI1/2. There is a bug that EC3 RGMII could not work when selecting EC1 as other functionality except RGMII. The workaround is to select ge2_clk125 for eTSEC clock muxing in register SCFG_ETSECCMCR. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | arm: ls102xa: Add SystemID EEPROM support for LS1021ATWR boardAlison Wang2014-11-24-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SystemID information could be read through I2C1 from EEPROM on LS1021ATWR board. As LS1 is a little-endian processor, getting the version ID by be32_to_cpu() is wrong. Fix it by using e.version directly. This change will be compatible for both ARM and PowerPC. As there is an errata that I2C1 could not work in SD boot, reading EEPROM through I2C1 is disabled too in SD boot. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | arm: ls102xa: Remove bit reversing for SCFG registersAlison Wang2014-11-24-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SCFG_SCFGREVCR is SCFG bit reverse register. This register must be written with 0xFFFFFFFF before writing to any other SCFG register. Then other SCFG register could be written in big-endian mode. Address: 157_0000h base + 200h offset = 157_0200h Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 W/R SCFGREV Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0-31 SCFGREV SCFG Bit Reverse Control Filed 32'h 0000_0000 - No bit reverse is applied 32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as 0:31 This patch removes the bit reversing for SCFG registers in u-boot. It will be implemented through PBI commands in RCW .pbi write 0x570200, 0xffffffff .end So other SCFG register could be written in big-endian mode in u-boot or kernel directly. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | arm: ls102xa: Add snoop disable for slave port 0, 1 and 2Jason Jin2014-11-24-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | Disable the snoop for slave interface 0, 1 and 2 to avoid the interleaving on the CCI400 BUS. Signed-off-by: Jason Jin <Jason.Jin@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | qe: add qe support for ls1021a-twr boardZhao Qiang2014-11-19-0/+8
| | | | | | | | | | | | | | | Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | qe: add qe support to ls1021aqdsZhao Qiang2014-11-19-0/+8
| | | | | | | | | | | | | | | | | | | | | add qe support to ls1021aqds Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2014-11-26-9/+438
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/mmc/fsl_esdhc.c Signed-off-by: Tom Rini <trini@ti.com>
| * | | powerpc/t2080qds: fix for 1000BASE-KXShaohui Xie2014-11-19-0/+99
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1000BASE-KX(1G-KX) uses SGMII protocol but the serdes lane runs in 1G-KX mode. By default, the lane runs in SGMII mode, when a MAC uses a lane in 1G-KX mode, corresponding bit in PCCR1 for the lane needs to be set, and needs to fixup dtb accordingly for kernel to do proper initialization. Hwconfig "fsl_1gkx" is used to indicate a MAC runs in 1G-KX mode, FM1 MAC 1/2/5/6/9/10 are available for 1G-KX, MAC 3/4 run in RGMII mode. To set a MAC runs in 1G-KX mode, set its' corresponding env in "fsl_1gkx", 'fm1_1g1' stands for FM1-MAC1, 'fm1_1g2' stands for FM1-MAC2, etc. If all MAC 1/2/5/6/9/10 run in 1G-KX mode, the hwconfig should has below setting: fsl_1gkx:fm1_1g1,fm1_1g2,fm1_1g5,fm1_1g6,fm1_1g9,fm1_1g10 Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> [York Sun: Fix compiling warning] Reviewed-by: York Sun <yorksun@freescale.com>
| * | | powerpc/t2080qds: fixup dtb for 10g-krshaohui xie2014-11-19-11/+98
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | XFI ports on t2080qds can work with fiber cable and direct attach cable(copper). We use hwconfig to define cable type for XFI, and fixup dtb based on the cable type. For copper cable, set below env in hwconfig: fsl_10gkr_copper:<10g_mac_name> the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4. fm1_10g1 stands for FM1-MAC9, fm1_10g2 stands for FM1-MAC10, fm1_10g3 stands for FM1-MAC1, fm1_10g4 stands for FM1-MAC2. The four <10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports, if a given 10G port will use the copper cable for 10GBASE-KR, set the <10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be assumed to be used for the port. For ex. if four XFI ports will both use copper cable, the hwconfig should contain: fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm1_10g3,fm1_10g4 Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | | board/t2080qds: add readme for t2080qdsShengzhou Liu2014-11-19-0/+243
| |/ / | | | | | | | | | | | | Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | | Merge branch 'master' of http://git.denx.de/u-boot-samsungTom Rini2014-11-26-0/+64
|\ \ \
| * | | odroid: Turn blue LED onSuriyan Ramasami2014-11-24-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To indicate that U-Boot is active, turn on the blue LED. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
generated by cgit v1.1 at 2024-11-11 08:40:18 +0000