summaryrefslogtreecommitdiff
path: root/board/xilinx
Commit message (Collapse)AuthorAgeLines
* Merge 'u-boot-microblaze/zynq' into (u-boot-arm/master'Albert ARIBAUD2013-09-03-0/+19
|\ | | | | | | | | | | | | Conflicts: arch/arm/include/asm/arch-zynq/hardware.h The conflict above was trivial and solved during merge.
| * zynq: Enable axi ethernet and emaclite driver initializationMichal Simek2013-08-12-0/+17
| | | | | | | | | | | | | | | | Zynq can have axi ethernet and emaclite IPs in programmable logic. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * zynq: Add new ddrc driver for ECC supportMichal Simek2013-08-12-0/+2
| | | | | | | | | | | | | | | | | | | | The first 1MB is not initialized by first stage bootloader. Check if memory is setup to 16bit mode and ECC is enabled. If it is, clear the first 1MB. Also u-boot should report only the half size of memory. Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | fpga: zynqpl: Add support for zc7100 device.Michal Simek2013-08-12-0/+4
|/ | | | | | | | | | - Add support for zc7100 device. - FPGA programming on few of the SOC(zc7100) takes more than 1sec, hence increased the program time by 4sec to sync' all soc's. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* xilinx: move microblaze-generic .dts to standard locationStephen Warren2013-08-02-1/+0
| | | | | | | | | | Aside from microblaze, all other SoCs/boards/vendors store their DT files in board/$vendor/dts/$soc-$board.dts. Move microblaze-generic.dts to this location for consistency. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Michal Simek <monstr@monstr.eu>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-238/+17
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-05-30-5/+12
|\ | | | | | | | | | | Conflicts: common/cmd_fpga.c drivers/usb/host/ohci-at91.c
| * gpio: Add support for microblaze xilinx GPIOMichal Simek2013-05-09-5/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Microblaze uses gpio which is connected to the system reset. Currently gpio subsystem wasn't used for it. Add gpio driver and change Microblaze reset logic to be done via gpio subsystem. There are various configurations which Microblaze can have that's why gpio_alloc/gpio_alloc_dual(for dual channel) function has been introduced and gpio can be allocated dynamically. Adding several gpios IP is also possible and supported. For listing gpio configuration please use "gpio status" command This patch also remove one compilation warning: microblaze-generic.c: In function 'do_reset': microblaze-generic.c:38:47: warning: operation on '*1073741824u' may be undefined [-Wsequence-point] Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master'Albert ARIBAUD2013-05-11-3/+12
|\ \ | |/
| * watchdog: Add support for Xilinx Microblaze watchdogMichal Simek2013-04-30-0/+8
| | | | | | | | | | | | | | Watchdog can be used on Microblaze, PPC and Zynq hw designs. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
| * microblaze: Disable all cpu features before resetMichal Simek2013-04-30-1/+2
| | | | | | | | | | | | | | | | | | | | Fix microblaze soft reset function and disable all cpu features. Especially disable caches because IRQs were off by disable_interrupts(). Reported-by: John Williams <john.williams@xilinx.com> Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * microblaze: Fix reset functionMichal Simek2013-04-30-2/+2
| | | | | | | | | | | | | | | | | | | | Remove CONFIG_SYS_RESET_ADDRESS macro. It was there from historical point of view when soft reset was just jump to u-boot text start (not used right now). Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | fpga: zynq: Add support for loading bitstreamMichal Simek2013-05-06-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | Devcfg device requires to load bitstream in binary format. But u-boot also has an option for loading bitstream in bit format. Let's handle both cases by zynqpl driver. Also add suport for loading partial bitstreams. The first driver version was done by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
* | mmc: Add support for Xilinx Zynq sdhci controllerMichal Simek2013-04-30-0/+17
| | | | | | | | | | | | | | Add support for SD, MMC and eMMC card on Xilinx Zynq. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
* | net: gem: Preserve clk on emio interfaceDavid Andrey2013-04-30-2/+2
| | | | | | | | | | | | | | | | | | | | | | Avoid overwriting GEMx_RCLK_CTRL and GEMx_CLK_CTRL if the Ethernet interface is connect on EMIO Do not enable emio for this standard board configuration for now. Signed-off-by: David Andrey <david.andrey@netmodule.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
* | net: gem: Pass phy address to initDavid Andrey2013-04-30-2/+4
| | | | | | | | | | | | | | | | | | Pass the PHY address to the driver init to allow parallel use of both interfaces Signed-off-by: David Andrey <david.andrey@netmodule.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
* | zynq: Move macros to hardware.hMichal Simek2013-04-30-3/+9
|/ | | | | | | | Add all fixed addresses to hardware.h and change petalinux configuration to support this. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
* microblaze: Remove FSL support from generic boardMichal Simek2013-02-04-20/+0
| | | | | | | | This code was targetting one specific Microblaze platform configuration which is obsolete and fsl bus isn't used in this way. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* board: xilinx: Remove common folderMichal Simek2013-02-04-5865/+0
| | | | | | | | All these files was used for ancient xilinx drivers which are finally gone. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Rommel Custodio <sessyargc@gmail.com>
* board: xilinx: Remove unused ancient i2c driverMichal Simek2013-02-04-634/+0
| | | | | | | | There is new driver in the driver folder. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Rommel Custodio <sessyargc@gmail.com> Acked-by: Heiko Schocher <hs@denx.de>
* xilinx: Add new Zynq boardMichal Simek2012-10-04-0/+108
| | | | | | | | Add support for Xilinx Zynq board. Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Marek Vasut <marex@denx.de> CC: Joe Hershberger <joe.hershberger@gmail.com>
* microblaze: Clean microblaze initializationMichal Simek2012-09-11-0/+9
| | | | | | | | | Move board specific function to board_init function in board/ folder Remove externs from generic board.c Use board_init_f function in board.c file. Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Stephan Linz <linz@li-pro.net>
* microblaze: Wire up dts configurationStephan Linz2012-07-10-0/+8
| | | | | | | | | - enable OF control and embedded OF - set default device tree file name to 'microblaze' - add CPP to dtc proxy: board/xilinx/dts/microblaze.dts - add an empty but processable dts for microblaze-generic Signed-off-by: Stephan Linz <linz@li-pro.net>
* microblaze: Move individual board linker scripts to common script in cpu tree.Michal Simek2012-07-09-71/+0
| | | | | | Unification for all microblaze boards. Signed-off-by: Michal Simek <monstr@monstr.eu>
* microblaze: Wire up LL_TEMAC driver initializationStephan Linz2012-04-04-0/+36
| | | | | | | Initialize ll_temac driver. Reported-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Stephan Linz <linz@li-pro.net>
* microblaze: Add faked LL_TEMAC driver configurationStephan Linz2012-04-04-4/+14
| | | | | | | | | | | | | | Expand the specific configuration for the microblaze-generic board in xparameters.h with a faked setup to enable the LL_TEMAC driver. Note: From now the microblaze-generic board is no longer a valid board configuration for a real piece of hardware. Rather than, we use the file config.mk and xparameters.h as a faked board configuration to force the compilation of all potential driver code for Microblaze systems. Signed-off-by: Stephan Linz <linz@li-pro.net>
* microblaze: Wire up axi_ethernet driver initializationMichal Simek2011-10-24-0/+6
| | | | | | Initialize axi_ethernet driver. Signed-off-by: Michal Simek <monstr@monstr.eu>
* net: xilinx_enet: drop unused !NET_MULTI driverMike Frysinger2011-10-23-4957/+0
| | | | | | | This driver doesn't support the NET_MULTI framework, and I can't find any boards/configs/files that reference this subdir, so punt it all. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* net: emaclite: Move RX/TX ping pong initialization toMichal Simek2011-10-23-6/+12
| | | | | | Init RX/TX ping pong directly from board not in the driver. Signed-off-by: Michal Simek <monstr@monstr.eu>
* punt unused clean/distclean targetsMike Frysinger2011-10-15-18/+0
| | | | | | | | | | The top level Makefile does not do any recursion into subdirs when cleaning, so these clean/distclean targets in random arch/board dirs never get used. Punt them all. MAKEALL didn't report any errors related to this that I could see. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Handle most LDSCRIPT setting centrallyScott Wood2011-04-30-12/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, some linker scripts are found by common code in config.mk. Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is sometimes in arch config.mk and sometimes in board config.mk. Some are found using an arch-specific rule for looking in CPUDIR, etc. Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds. Replace all of this -- except for a handful of boards that are actually selecting a linker script in a unique way -- with centralized ldscript finding. If board code specifies LDSCRIPT, that will be used. Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used. If neither of these are specified, then the central config.mk will check for the existence of the following, in order: $(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT) $(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT) $(TOPDIR)/board/$(BOARDDIR)/u-boot.lds $(TOPDIR)/$(CPUDIR)/u-boot.lds Some boards (sc3, cm5200, munices) provided their own u-boot.lds that were dead code, because they were overridden by a CPUDIR u-boot.lds under the old powerpc rules. These boards' own u-boot.lds have bitrotted and no longer work -- these lds files have been removed. Signed-off-by: Scott Wood <scottwood@freescale.com> Tested-by: Graeme Russ <graeme.russ@gmail.com>
* xilinx-ppc4xx-generic: Fix Makefile to work with MAKEALLRicardo Ribalda Delgado2011-01-11-18/+7
| | | | | | | | | config.mk only mkdirs $(obj), but we have objects shared with other boards located on other dirs. This patch mkdirs the needed dirs for the xlnx-generic boards. Signed-off-by: Stefan Roese <sr@denx.de>
* xilinx-ppc4xx-generic: Use common u-boot.ldsRicardo Ribalda Delgado2010-12-17-548/+6
| | | | | | | Use common ppc4xx linker script for xilinx ppc440 and ppc405 related boards. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
* do_reset: unify duplicate prototypesMike Frysinger2010-11-28-1/+2
| | | | | | | The duplication of the do_reset prototype has gotten out of hand, and they're not all in sync. Unify them all in command.h. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Switch from archive libraries to partial linkingSebastien Carlier2010-11-17-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | Before this commit, weak symbols were not overridden by non-weak symbols found in archive libraries when linking with recent versions of binutils. As stated in the System V ABI, "the link editor does not extract archive members to resolve undefined weak symbols". This commit changes all Makefiles to use partial linking (ld -r) instead of creating library archives, which forces all symbols to participate in linking, allowing non-weak symbols to override weak symbols as intended. This approach is also used by Linux, from which the gmake function cmd_link_o_target (defined in config.mk and used in all Makefiles) is inspired. The name of each former library archive is preserved except for extensions which change from ".a" to ".o". This commit updates references accordingly where needed, in particular in some linker scripts. This commit reveals board configurations that exclude some features but include source files that depend these disabled features in the build, resulting in undefined symbols. Known such cases include: - disabling CMD_NET but not CMD_NFS; - enabling CONFIG_OF_LIBFDT but not CONFIG_QE. Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
* Makefile: move all Power Architecture boards into boards.cfgWolfgang Denk2010-10-18-76/+12
| | | | | | | | | | Clean up Makefile, and drop a lot of the config.mk files on the way. We now also automatically pick all boards that are listed in boards.cfg (and with all configurations), so we can drop the redundant entries from MAKEALL to avoid building these twice. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Rename TEXT_BASE into CONFIG_SYS_TEXT_BASEWolfgang Denk2010-10-18-5/+5
| | | | | | | | | | | | The change is currently needed to be able to remove the board configuration scripting from the top level Makefile and replace it by a simple, table driven script. Moving this configuration setting into the "CONFIG_*" name space is also desirable because it is needed if we ever should move forward to a Kconfig driven configuration system. Signed-off-by: Wolfgang Denk <wd@denx.de>
* microblaze: Add support for NET_MULTI apiMichal Simek2010-10-12-0/+13
| | | | | | Microblaze hasn't supported NET_MULTI support. Signed-off-by: Michal Simek <monstr@monstr.eu>
* Merge branch 'master' of git://git.denx.de/u-boot-microblazeWolfgang Denk2010-04-24-4/+3
|\
| * microblaze: Move FSL initialization to board.cMichal Simek2010-04-16-4/+3
| | | | | | | | | | | | Move FSL out of interrupt controller. Signed-off-by: Michal Simek <monstr@monstr.eu>
* | Move arch/ppc to arch/powerpcStefan Roese2010-04-21-2/+2
|/ | | | | | | | | | | | | | | | | As discussed on the list, move "arch/ppc" to "arch/powerpc" to better match the Linux directory structure. Please note that this patch also changes the "ppc" target in MAKEALL to "powerpc" to match this new infrastructure. But "ppc" is kept as an alias for now, to not break compatibility with scripts using this name. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Wolfgang Denk <wd@denx.de> Acked-by: Detlev Zundel <dzu@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Anatolij Gustschin <agust@denx.de>
* microblaze: Move cpu/microblaze/* to arch/microblaze/cpu/*Peter Tyser2010-04-13-1/+1
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* ppc: Move cpu/$CPU to arch/ppc/cpu/$CPUPeter Tyser2010-04-13-2/+2
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Replace "#include <asm-$ARCH/$FILE>" with "#include <asm/$FILE>"Peter Tyser2010-04-13-1/+1
| | | | | | | | | | The appropriate include/asm-$ARCH directory should already by symlinked to include/asm so using the whole "asm-$ARCH" path is unnecessary. This change should also allow us to move the include/asm-$ARCH directories into their appropriate lib/$ARCH/ directories. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* ml300: remove support for broken, orphaned boardWolfgang Denk2010-03-28-1434/+0
| | | | | | | | The ml300 board has a number of issues, but nobody cares about this long-orphaned board any more. Remove it. Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Michal Simek <monstr@monstr.eu>
* ppc4xx: Add custom linker script to board/*/config.mkStefan Roese2009-11-02-0/+3
| | | | | | | | These boards have special linker scripts right now. We can't use the common 4xx linker script here. So overrride the linker script (LDSCRIPT) in board/*/config.mk and choose the board specific version. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc: Enable full relocation to RAMPeter Tyser2009-10-03-6/+0
| | | | | | | | | | | | | The following changes allow U-Boot to fully relocate from flash to RAM: - Remove linker scripts' .fixup sections from the .text section - Add -mrelocatable to PLATFORM_RELFLAGS for all boards - Define CONFIG_RELOC_FIXUP_WORKS for all boards Previously, U-Boot would partially relocate, but statically initialized pointers needed to be manually relocated. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* microblaze: Add sbss, scommon and COMMON symbols for clearingMichal Simek2009-09-14-0/+3
| | | | Signed-off-by: Michal Simek <monstr@monstr.eu>
* unify HOST_CFLAGS and HOSTCFLAGSMike Frysinger2009-07-23-3/+3
| | | | | | | | The top build system sets up HOSTCFLAGS a bit and exports it, but other places use HOST_CFLAGS instead. Unify the two as HOSTCFLAGS so that the values stay in sync. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Fix all linker script to handle all rodata sectionsTrent Piepho2009-03-20-16/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A recent gcc added a new unaligned rodata section called '.rodata.str1.1', which needs to be added the the linker script. Instead of just adding this one section, we use a wildcard ".rodata*" to get all rodata linker section gcc has now and might add in the future. However, '*(.rodata*)' by itself will result in sub-optimal section ordering. The sections will be sorted by object file, which causes extra padding between the unaligned rodata.str.1.1 of one object file and the aligned rodata of the next object file. This is easy to fix by using the SORT_BY_ALIGNMENT command. This patch has not be tested one most of the boards modified. Some boards have a linker script that looks something like this: *(.text) . = ALIGN(16); *(.rodata) *(.rodata.str1.4) *(.eh_frame) I change this to: *(.text) . = ALIGN(16); *(.eh_frame) *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) This means the start of rodata will no longer be 16 bytes aligned. However, the boundary between text and rodata/eh_frame is still aligned to 16 bytes, which is what I think the real purpose of the ALIGN call is. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>