| Commit message (Collapse) | Author | Age | Lines |
|---|
| |
|
|
| |
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
| |
|
|
| |
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
| | |
|
| |
|
|
|
|
|
|
|
|
|
| |
With the new LAW interface (set_next_law) we can move to letting the
system allocate which LAWs are used for what purpose. This makes life
a bit easier going forward with the new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Some TQM85xx boards could be equipped with up to 1 GiB (NOR) Flash
memory. The current memory map only supports up to 128 MiB Flash.
This patch adds the configuration option CONFIG_TQM_BIGFLASH. If
set, up to 1 GiB flash is supported. To achieve this, the memory
map has to be adjusted in great parts (for example the CCSRBAR is
moved from 0xE0000000 to 0xA0000000).
If you want to boot Linux with CONFIG_TQM_BIGFLASH set, the new
memory map also has to be considered in the kernel (changed
CCSRBAR address, changed PCI IO base address, ...). Please use
an appropriate Flat Device Tree blob (tqm8548.dtb).
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for NAND FLASH on the TQM8548. It is disabled by
default and can be enabled for the TQM8548 modules. It is now based on
the re-written FSL NAND UPM driver. A patch has been posted earlier today
with the subject:
"NAND FSL UPM: driver re-write using the hwcontrol callback"
Note that the R/B pin is not supported by that module requiring to use
the specified maximum delay time.
Note: With NAND support enabled the size of the U-Boot image exceeds
256 KB and TEXT_BASE must therefore be set to 0xfff80000 in config.mk,
doubling the image size :-(.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
|
| |
|
|
|
|
|
|
|
| |
This patch adds support for PCI express cards. The board support
now uses common FSL PCI init code, for both, PCI and PCIe on all
TQM85xx modules.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
This patch adds basic support for the TQM8548 module from TQ-Components
(http://www.tqc.de/) including DDR2 SDRAM initialisation and support for
eTSEC 3 and 4
Furthermore Flash buffer write has been enabled to speed up output to
the Flash by approx. a factor of 10.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
|
| |
|
|
|
|
|
|
| |
This patch adds support for Linux kernels using the Flat Device Tree.
It also re-defines the default environment settings for booting Linux
with the FDT blob.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
|
| |
|
|
|
|
|
|
| |
This patch adds initialization of the UPMC RAM to support up to two
Intel 82527 compatible CAN controller on the TQM85xx modules.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
|
| |
|
|
|
|
|
| |
The CS0_BNDS register is now set according to the detected
memory size.
Signed-off-by Martin Krause <martin.krause@tqs.de>
|
| |
|
|
|
|
|
| |
This patch fixes the re-calculation of the automatic chip select
configuration for boards with two populated FLASH banks.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
|
| |
|
|
|
|
|
|
|
| |
Do not configure port pins PD30/PD31 as SCC1 TxD/RxD except for the TQM8560
board. On the other TQM85xx boards (TQM8541 and TQM8555) SCC1 is not used
as serial interface anyway. Worse, on some board variants configuring the
pins for SCC1 leads to short circuits (for example on the TQM8541-BG).
Signed-off-by: Martin Krause <martin.krause@tqs.de>
|
| |
|
|
| |
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
|
|
|
Move all TQM board directories to the vendor specific directory "tqc"
for modules from TQ-Components GmbH (http://www.tqc.de).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
|
