summaryrefslogtreecommitdiff
path: root/board/ti
Commit message (Collapse)AuthorAgeLines
...
* am335x_evm: Make SPL_OS also check the boot_os variable for falcon modeTom Rini2014-04-17-1/+12
| | | | | | | | | We use the same variable as a3m071 in the environment to determine if we should boot into Linux or U-Boot. This is useful on boards like Beaglebone Black or AM335x GP EVM where we have persistent storage for the environment. Signed-off-by: Tom Rini <trini@ti.com>
* OMAP3: beagle-xm: generate fake USB ethernet MAC address from dieidNishanth Menon2014-04-17-0/+11
| | | | | | | | Similar to OMAP5uEVM, PandaBoard, BeagleBoard-XM has a USB based ethernet without MAC address embedded. So fake a MAC address following the similar strategy used on OMAP5 and PandaBoard family. Signed-off-by: Nishanth Menon <nm@ti.com>
* OMAP: common: consolidate fake USB ethernet MAC address creationNishanth Menon2014-04-17-32/+14
| | | | | | | | | | | | | | TI platforms such as OMAP5uevm, PandaBoard, use equivalent logic to generate fake USB MAC address from device unique DIE ID. Consolidate this to a generic location such that other TI platforms such as BeagleBoard-XM can also use the same. NOTE: at this point in time, I dont yet see a need for a generic dummy ethernet MAC address creation function, but if there is a need in the future, this can be further abstracted out. Signed-off-by: Nishanth Menon <nm@ti.com>
* ARM: OMAP: remove sr32() from OMAP board codeWolfgang Denk2014-04-17-1/+1
| | | | | | | | | | Replace the custom sr32() bit manipulation function in arch/arm/cpu/armv7/omap3/board.c and board/ti/panda/panda.c by standard I/O accessors. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2014-04-08-2/+17
|\ | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile include/configs/trats.h include/configs/trats2.h include/mmc.h
| * mmc: Add 'mmc rst-function' sub-commandTom Rini2014-04-02-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | Some eMMC chips may need the RST_n_FUNCTION bit set to a non-zero value in order for warm reset of the system to work. Details on this being required will be part of the eMMC datasheet. Also add using this command to the dra7xx README. * Whitespace fix by panto Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
| * am335x_evm: Clarify when we build board_eth_initTom Rini2014-03-28-2/+16
| | | | | | | | | | | | | | | | If we build this function in cases where we would be discarding it anyhow we still end up with maybe unused warnings. Rather than litter the function with __maybe_unused, just spell out when to build it. Signed-off-by: Tom Rini <trini@ti.com>
* | arm: Handle .gnu.hash section in ldscriptsAndreas Färber2014-04-07-0/+1
|/ | | | | | | | | | Avoids "could not find output section .gnu.hash" ld.bfd errors on openSUSE. Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-03-10-9/+177
|\
| * ARM: AM43xx: Add Ethernet boot support to SPLMugunthan V N2014-03-04-2/+0
| | | | | | | | | | | | | | Add Ethernet Boot support to SPL Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
| * ARM: AM4372: Update EMIF registers for DDR3Lokesh Vutla2014-03-04-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Updating EMIF_PHY_CTRL and adding EMIF_READ_WRITE_EXECUTION_THRESHOLD registers. In EMIF_PHY_CTRL: Updating [4:0]READ_LATENCY to 8, because at higher frequencies like 400MHz the read latency expected will be CL+3 as per tests from HW folks. Clearing [19]PHY_DIS_CALIB_RST bit as this is used onl for debug purpose. With out this resume is not working(Still waiting for PHY team to come back for better explanation). Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: DRA7xx: add support for reading cpsw 2nd mac from efuseMugunthan V N2014-03-04-0/+15
| | | | | | | | | | | | | | | | | | Adding support for reading cpsw 2nd mac address from efuse and pass it to kernel via dtb which will be used in dual emac mode of cpsw. Also correct the bit masking of mac id read from the efuse. Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
| * ARM: AM335x: add support for reading cpsw 2nd mac address from efuseMugunthan V N2014-03-04-0/+15
| | | | | | | | | | | | | | | | | | Adding support for reading cpsw 2nd mac address from efuse and pass it to kernel via dtb which will be used in dual emac mode of cpsw. Also adding mii command support to am335x common config. Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
| * ARM: AM43xx: Add CPSW support to AM43xx EPOS and GP EVMMugunthan V N2014-03-04-2/+142
| | | | | | | | | | | | | | | | Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected to RMII and RGMII phy respectively and enable cpsw in config. Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
| * drivers: net: cpsw: add support to have phy address from cpsw platform dataMugunthan V N2014-03-04-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | Some platforms like AM437x have different EVMs with different phy addresses, so this patch adds support for passing phy address via cpsw plaform data. Also renamed phy_id to phy_addr so better understanding of the code. Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> [trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335 pengwyn boards] Signed-off-by: Tom Rini <trini@ti.com>
* | board/ti/am335x/README: update for NAND bootpekon gupta2014-03-03-17/+36
|/ | | | | | | | | NAND boot mode on AM335x EVM has been verified, and steps to use it has been documented and update in this README Signed-off-by: Pekon Gupta <pekon@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Tom Rini <trini@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-02-26-17/+18
|\ | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/armv7/config.mk board/ti/am43xx/mux.c include/configs/am43xx_evm.h Signed-off-by: Tom Rini <trini@ti.com>
| * arm: remove unneeded symbol offsets and _TEXT_BASEAlbert ARIBAUD2014-02-26-4/+0
| | | | | | | | | | | | | | | | Remove the last uses of symbol offsets in ARM U-Boot. Remove some needless uses of _TEXT_BASE. Remove all _TEXT_BASE definitions. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
| * arm: make _end compiler-generatedAlbert ARIBAUD2014-02-26-2/+7
| | | | | | | | | | | | | | | | | | This prevents references to _end from generating absolute relocation records. This change is binary invariant for ARM targets. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
| * ARM: AM43xx: GP-EVM: Correct GPIO used for VTT regulator controlDave Gerlach2014-02-21-11/+11
| | | | | | | | | | | | | | | | | | | | | | Schematic indicates GPIO5_7 is to be used for VTT regulator control rather than GPIO0_21 so modify enable_vtt_regulator to reflect this. Without this some boards will experience DDR3 corruption and fail to boot. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> [trini: Rework patch against mainline] Signed-off-by: Tom Rini <trini@ti.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini2014-02-21-0/+11
|\ \ | |/ |/|
| * am437x_epos_evm: add SPL API, QSPI, and serial flash supportSourav Poddar2014-02-18-0/+11
| | | | | | | | | | | | | | | | Enables support for SPI SPL, QSPI and Spansion serial flash device on the EVM. Configures pin muxes for QSPI mode. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* | ARM: O5/dra7xx: Add SATA boot supportDan Murphy2014-02-19-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | Add the SATA boot support for OMAP5 and dra7xx. Renamed the omap_sata_init to the common init_sata(int dev) for commonality in with sata stack. Added the ROM boot device ID for SATA. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-02-17-681/+1
|\ \
| * | ARM: AM43xx: Enable DDR dynamic IO power down for DDR3Lokesh Vutla2014-01-24-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables dynamically powering down the IO receiver when not performing a read on DDR3 board. This optimizes both active and standby power consumption. This is derived from a patch that is done on AM335x[1] [1] http://arago-project.org/git/projects/?p=u-boot-am33x.git;a=commit;h=6a9ee4bc72ece53fabf01825605fba3d71d5feb2 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * | ARM: OMAP4/5: Remove dead code against CONFIG_SYS_ENABLE_PADS_ALLJassi Brar2014-01-24-680/+0
| |/ | | | | | | | | | | | | | | | | The commit f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls" removed the config option aimed towards moving that stuff into kernel, which renders some code unreachable. Remove that code. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
* | dra7xx_evm: Add CONFIG_SUPPORT_EMMC_BOOT, document usageTom Rini2014-02-07-0/+25
| | | | | | | | | | | | | | | | | | Add a README to the board which lists the commands required to enable booting from the eMMC boot partitions found on the board. Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* | omap5_uevm: Add CONFIG_SUPPORT_EMMC_BOOT, document usageTom Rini2014-02-07-0/+25
|/ | | | | | | | Add a README to the board which lists the commands required to enable booting from the eMMC boot partitions found on the board. Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* ARM: dra7_evm: read mac address properly from e-fuseMugunthan V N2014-01-07-4/+4
| | | | | | | Byte offset of Ethernet mac address read from e-fuse are wrong so DHCP is not working on some boards, modifying the offset to read properly. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* ARM: AM43xx: GP_EVM: Add support for DDR3Lokesh Vutla2013-12-18-3/+98
| | | | | | | | | | | | | | | | GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH). Adding details for the same. Below is the brief description of DDR3 init sequence(SW leveling): -> Enable VTT regulator -> Configure VTP -> Configure DDR IO settings -> Disable initialization and refreshes until EMIF registers are programmed. -> Program Timing registers -> Program leveling registers -> Program PHY control and Temp alert and ZQ config registers. -> Enable initialization and refreshes and configure SDRAM CONFIG register Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: AM43xx: EPOS_EVM: Add support for LPDDR2Lokesh Vutla2013-12-18-0/+66
| | | | | | | | | | | | | | | AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A) Adding LPDDR2 init sequence and register details for the same. Below is the brief description of LPDDR2 init sequence: -> Configure VTP -> Configure DDR IO settings -> Disable initialization and refreshes until EMIF registers are programmed. -> Program Timing registers -> Program PHY control and Temp alert and ZQ config registers. -> Enable initialization and refreshes and configure SDRAM CONFIG register -> Wait till initialization is complete and the configure MR registers. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: AM33xx+: Update ioregs to pass different valuesLokesh Vutla2013-12-18-10/+46
| | | | | | | | | | | Currently same value is programmed for all ioregs. This is not the case for all SoC's like AM4372. So adding a structure for ioregs and updating in all board files. And also return from config_cmd_ctrl() and config_ddr_data() functions if data is not passed. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> [trini: Fixup dxr2, cm_t335, adapt pcm051 rev3] Signed-off-by: Tom Rini <trini@ti.com>
* ARM: AM43xx: clocks: Update DPLL detailsLokesh Vutla2013-12-18-3/+144
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Updating the Multiplier and Dividers value for all DPLLs. Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value returned the MPU DPLL is locked. At different OPPs follwoing are the MPU locked frequencies. OPP50 300MHz OPP100 600MHz OPP120 720MHz OPPTB 800MHz OPPNT 1000MHz According to the latest DM following is the OPP table dependencies: VDD_CORE VDD_MPU OPP50 OPP50 OPP50 OPP100 OPP100 OPP50 OPP100 OPP100 OPP100 OPP120 So at different OPPs of MPU it is safest to lock CORE at OPP_NOM. Following are the DPLL locking frequencies at OPP NOM: Core locks at 1000MHz Per locks at 960MHz LPDDR2 locks at 266MHz DDR3 locks at 400MHz Touching AM33xx files also to get DPLL values specific to board but no functionality difference. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: AM43xx: mux: Update mux dataLokesh Vutla2013-12-18-2/+20
| | | | | | | Updating the mux data for UART, adding data for i2c0 and mmc. And also updating pad_signals structure. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: AM43XX: Add CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG supportSekhar Nori2013-12-18-0/+16
| | | | | | | | | CONFIG_ENV_VARS_UBOOT_CONFIG, CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and CONFIG_BOARD_LATE_INIT is already set. Adding support to detect the board. These variables are used by findfdt. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: AM43XX: board: add support for reading onboard EEPROMSekhar Nori2013-12-18-0/+78
| | | | | | | | Add support for reading onboard EEPROM to enable board detection. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: AM43xx: Adapt to ti_armv7_common.h config fileLokesh Vutla2013-12-18-1/+1
| | | | | | | Use ti_armv7_common.h config file to inclde the common configs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-12-10-20/+8
|\ | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/armv7/rmobile/Makefile doc/README.scrapyard Needed manual fix: arch/arm/cpu/armv7/omap-common/Makefile board/compulab/cm_t335/u-boot.lds
| * Merge branch 'master' of git://git.denx.de/u-boot-nand-flashTom Rini2013-11-25-13/+1
| |\
| | * am335x: fix GPMC config for NAND and NOR SPL bootpekon gupta2013-11-21-13/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | GPMC controller is common IP to interface with both NAND and NOR flash devices. Also, it supports max 8 chip-selects, which can be independently connected to any of the devices. But ROM code expects the boot-device to be connected to only chip-select[0]. Thus to resolve conflict between NOR and NAND boot. This patch: - combines NOR and NAND configs spread in board files to common gpmc_init() - configures GPMC based on boot-mode selected for SPL boot. Signed-off-by: Pekon Gupta <pekon@ti.com>
| * | Makefile: rename all libraries to built-in.oMasahiro Yamada2013-11-17-1/+1
| | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
| * | Makefile: specifiy an explicite object name rather than $(BOARD).oMasahiro Yamada2013-11-17-1/+1
| | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
| * | i2c, omap24xx: convert driver to new mutlibus/mutliadapter frameworkHeiko Schocher2013-11-13-5/+5
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - add omap24xx driver to new multibus/multiadpater support - adapted all config files, which uses this driver Tested on the am335x based siemens boards rut, dxr2 and pxm2 posted here: http://patchwork.ozlabs.org/patch/263211/ Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Tom Rini <trini@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Thomas Weber <weber@corscience.de> Cc: Tom Rix <Tom.Rix@windriver.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Nishanth Menon <nm@ti.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Michael Jones <michael.jones@matrix-vision.de> Cc: Raphael Assenat <raph@8d.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Stefano Babic <sbabic@denx.de>
* | arm: keep all sections in ELF fileAlbert ARIBAUD2013-12-07-6/+9
| | | | | | | | | | | | | | | | | | | | Current LDS files /DISCARD/ a lot of sections when linking ELF files, causing diagnostic tools such as readelf or objdump to produce partial output. Keep all section at link stage, filter only at objcopy time so that .bin remains minimal. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | pandaboard: 1/1] ARM:OMAP4+: panda-es: Support Rev B3 Elpida DDR2 RAMHardik Patel2013-12-04-0/+60
| | | | | | | | Signed-off-by: Hardik Patel <hardik.patel@volansystech.com>
* | ARM: dra7_evm: Add SATA supportRoger Quadros2013-12-04-0/+7
| | | | | | | | | | | | | | The evm has a SATA port. Enable SATA configuration and inititialize the SATA controller. Signed-off-by: Roger Quadros <rogerq@ti.com>
* | ARM: omap5_uevm: Add SATA supportRoger Quadros2013-12-04-0/+7
| | | | | | | | | | | | The uevm has a SATA port. Inititialize the SATA controller. Signed-off-by: Roger Quadros <rogerq@ti.com>
* | am33xx: Stop modifying certain EMIF4D registersTom Rini2013-12-04-39/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on the definitive guide to EMIF configuration[1] certain registers that we have been modifying (and are documented registers) should be left in their reset values rather than modified. This has been tested on AM335x GP EVM and Beaglebone White. [1]: http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Javier Martinez Canillas <javier@dowhile0.org> Cc: Heiko Schocher <hs@denx.de> Cc: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Matt Porter <matt.porter@linaro.org>
* | omap730p2: Remove boardTom Rini2013-11-11-1222/+0
|/ | | | Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-11-09-0/+6
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
generated by cgit v1.1 at 2024-11-07 02:36:52 +0000