summaryrefslogtreecommitdiff
path: root/board/ti
Commit message (Collapse)AuthorAgeLines
* ARM: DRA7xx: Update the board_name env variableLokesh Vutla2014-07-14-0/+6
| | | | | | | Update the board_name env variable and accordingly populate the dtb file. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* am43xx: Tune the system to avoid DSS underflowsCooper Jr., Franklin2014-07-07-6/+62
| | | | | * This is done by limiting the ARM's bandwidth and setting DSS priority in the EMIF controller to ensure underflows do not occur.
* am43xx: Update EMIF DDR3 Configuration for AM43x GPFranklin S. Cooper Jr2014-07-07-0/+112
| | | | | | | | | * Boot failures have been discovered due to a combination of routing issues and non optimal ddr3 timings in the EMIF * Since ddr3 timings are different after significant board layout changes different timings are required for alpha, beta and production boards. Signed-off-by: Franklin S. Cooper Jr <fcooper@ti.com>
* board: ti: dra7xx: add mux data for UART3Felipe Balbi2014-07-07-0/+5
| | | | | | | | | | | | | J6 EVM can be built with UART3 as console, but currently there's nothing muxing UART3 correctly. Likely this only works because, based on commit log, author was only testing with UART3 boot and - I assume - ROM code leave UART3 correctly muxed in that case. If we want to boot from MMC and still use UART3 as console, then we need to mux those signals correctly. Signed-off-by: Felipe Balbi <balbi@ti.com>
* Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2014-07-01-8/+91
|\
| * board: ti: am43xx: enable QSPI and Gbit Ethernet on AM437x SKFelipe Balbi2014-06-19-0/+3
| | | | | | | | | | | | | | | | AM437x Starter Kit has a qspi flash and gbit ethernet support. By muxing those signals, we can use those interfaces from u-boot. Signed-off-by: Felipe Balbi <balbi@ti.com>
| * board: ti: am43xx: add AM437x SK PHY AddressFelipe Balbi2014-06-19-0/+5
| | | | | | | | | | | | | | | | pass correct PHY Address when running on SK so that we have working ethernet with this board too. Signed-off-by: Felipe Balbi <balbi@ti.com>
| * board: ti: am43xx: add support for AM43xx Starter KitFelipe Balbi2014-06-19-1/+76
| | | | | | | | | | | | | | | | | | | | AM43xx Starter Kit is a new board based on AM437x line of SoCs. Being a low-cost EVM and small size EVM are intended to provide an entry level development platform on a full fledged Hardware System. Signed-off-by: Felipe Balbi <balbi@ti.com>
| * board: ti: am43xx: print unsupported board nameFelipe Balbi2014-06-19-1/+1
| | | | | | | | | | | | | | | | | | when porting u-boot to a new am43xx board, it helps to know the name of the current unsupported board so we don't have to hunt for design documents to figure out what's written in the EEPROM. Signed-off-by: Felipe Balbi <balbi@ti.com>
| * ARM: keystone: aemif: move aemif driver to drivers/memory/ti-aemif.cKhoronzhuk, Ivan2014-06-19-4/+5
| | | | | | | | | | | | | | | | Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * mtd: nand: davinci: add header file for driver definitionsKhoronzhuk, Ivan2014-06-19-2/+1
| | | | | | | | | | | | | | | | | | | | | | The definitions inside emif_defs.h concern davinci nand driver and should be in it's header. So create header file for davinci nand driver and move definitions from emif_defs.h and nand_defs.h to it. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> [trini: Fixup more davinci breakage] Signed-off-by: Tom Rini <trini@ti.com>
* | ti: am335x: Fix the U-Boot binary outputSimon Glass2014-06-11-1/+2
|/ | | | | | | This should include the hash so that image_binary_size is really at the end of the image, and not some 300 bytes earlier. Signed-off-by: Simon Glass <sjg@chromium.org>
* arm:am43xx: Add TPS65218 support to scale voltages upTom Rini2014-06-06-7/+41
| | | | | | | | This family is supported by the TPS65218 PMIC. Implement a scale_vcores to set the MPU and CORE voltage correctly to the max frequency that is supported (and what we will be scaling them to in setup_dplls()). Signed-off-by: Tom Rini <trini@ti.com>
* am43xx: Only read the MPU frequency bits of CTRL_DEV_ATTRTom Rini2014-06-06-1/+4
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* am43xx_evm: Add qspiboot targetSourav Poddar2014-06-06-2/+2
| | | | | | | | | | | | | The ePOS EVM and EVM SK have QSPI as an option to boot. Add a qspiboot target that utilizes QSPI for env and so forth as an example of best practices. As QSPI is booted from directly we need to chang CONFIG_SYS_TEXT_BASE. Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices we need to handle that elsewhere, once NAND support is also added. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* arm: move exception handling out of start.S filesAlbert ARIBAUD2014-05-15-0/+1
| | | | | | | | Exception handling is basically identical for all ARM targets. Factorize it out of the various start.S files and into a single vectors.S file, and adjust linker scripts accordingly. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* am335x: Switch to CONFIG_SKIP_LOWLEVEL_INIT from guarding SPL or NOR_BOOTTom Rini2014-04-17-2/+2
| | | | | | | | | | In the case of SPL or NOR_BOOT (no SPL involved) we need to include certain code in the build. Use !CONFIG_SKIP_LOWLEVEL_INIT rather than CONFIG_SPL_BUILD || CONFIG_NOR_BOOT to make the code clearer, and to make supporting XIP QSPI boot clearer in the code. Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Wolfgang Denk <wd@denx.de>
* keystone2: net: add keystone ethernet driverKaricheri, Muralidharan2014-04-17-0/+65
| | | | | | | | | | | | Ethernet driver configures the CPSW, SGMI and Phy and uses the the Navigator APIs. The driver supports 4 Ethernet ports and can work with only one port at a time. Port configurations are defined in board.c. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
* k2hk: add support for k2hk SOC and EVMVitaly Andrianov2014-04-17-0/+635
| | | | | | | | | | | | | | k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please refer the ti/k2hk_evm/README for details on the board, build and other information. This patch add support for keystone architecture and k2hk evm. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
* dra7xx_evm: Add QSPI_4 support, qspiboot build targetTom Rini2014-04-17-0/+19
| | | | | | | | | | | | We previously only supported QSPI_1 (single) support. Add QSPI_4 (quad) read support as well. This means we can be given one of two boot device values, but don't care which it is, so perform a fixup on the QSPI_4 value. We add a qspiboot build target to better show how you would use QSPI as a boot device in deployment. When we boot from QSPI, we can check the environment for 'boot_os' to control Falcon Mode. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Make SPL_OS also check the boot_os variable for falcon modeTom Rini2014-04-17-1/+12
| | | | | | | | | We use the same variable as a3m071 in the environment to determine if we should boot into Linux or U-Boot. This is useful on boards like Beaglebone Black or AM335x GP EVM where we have persistent storage for the environment. Signed-off-by: Tom Rini <trini@ti.com>
* OMAP3: beagle-xm: generate fake USB ethernet MAC address from dieidNishanth Menon2014-04-17-0/+11
| | | | | | | | Similar to OMAP5uEVM, PandaBoard, BeagleBoard-XM has a USB based ethernet without MAC address embedded. So fake a MAC address following the similar strategy used on OMAP5 and PandaBoard family. Signed-off-by: Nishanth Menon <nm@ti.com>
* OMAP: common: consolidate fake USB ethernet MAC address creationNishanth Menon2014-04-17-32/+14
| | | | | | | | | | | | | | TI platforms such as OMAP5uevm, PandaBoard, use equivalent logic to generate fake USB MAC address from device unique DIE ID. Consolidate this to a generic location such that other TI platforms such as BeagleBoard-XM can also use the same. NOTE: at this point in time, I dont yet see a need for a generic dummy ethernet MAC address creation function, but if there is a need in the future, this can be further abstracted out. Signed-off-by: Nishanth Menon <nm@ti.com>
* ARM: OMAP: remove sr32() from OMAP board codeWolfgang Denk2014-04-17-1/+1
| | | | | | | | | | Replace the custom sr32() bit manipulation function in arch/arm/cpu/armv7/omap3/board.c and board/ti/panda/panda.c by standard I/O accessors. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2014-04-08-2/+17
|\ | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile include/configs/trats.h include/configs/trats2.h include/mmc.h
| * mmc: Add 'mmc rst-function' sub-commandTom Rini2014-04-02-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | Some eMMC chips may need the RST_n_FUNCTION bit set to a non-zero value in order for warm reset of the system to work. Details on this being required will be part of the eMMC datasheet. Also add using this command to the dra7xx README. * Whitespace fix by panto Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
| * am335x_evm: Clarify when we build board_eth_initTom Rini2014-03-28-2/+16
| | | | | | | | | | | | | | | | If we build this function in cases where we would be discarding it anyhow we still end up with maybe unused warnings. Rather than litter the function with __maybe_unused, just spell out when to build it. Signed-off-by: Tom Rini <trini@ti.com>
* | arm: Handle .gnu.hash section in ldscriptsAndreas Färber2014-04-07-0/+1
|/ | | | | | | | | | Avoids "could not find output section .gnu.hash" ld.bfd errors on openSUSE. Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-03-10-9/+177
|\
| * ARM: AM43xx: Add Ethernet boot support to SPLMugunthan V N2014-03-04-2/+0
| | | | | | | | | | | | | | Add Ethernet Boot support to SPL Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
| * ARM: AM4372: Update EMIF registers for DDR3Lokesh Vutla2014-03-04-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Updating EMIF_PHY_CTRL and adding EMIF_READ_WRITE_EXECUTION_THRESHOLD registers. In EMIF_PHY_CTRL: Updating [4:0]READ_LATENCY to 8, because at higher frequencies like 400MHz the read latency expected will be CL+3 as per tests from HW folks. Clearing [19]PHY_DIS_CALIB_RST bit as this is used onl for debug purpose. With out this resume is not working(Still waiting for PHY team to come back for better explanation). Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: DRA7xx: add support for reading cpsw 2nd mac from efuseMugunthan V N2014-03-04-0/+15
| | | | | | | | | | | | | | | | | | Adding support for reading cpsw 2nd mac address from efuse and pass it to kernel via dtb which will be used in dual emac mode of cpsw. Also correct the bit masking of mac id read from the efuse. Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
| * ARM: AM335x: add support for reading cpsw 2nd mac address from efuseMugunthan V N2014-03-04-0/+15
| | | | | | | | | | | | | | | | | | Adding support for reading cpsw 2nd mac address from efuse and pass it to kernel via dtb which will be used in dual emac mode of cpsw. Also adding mii command support to am335x common config. Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
| * ARM: AM43xx: Add CPSW support to AM43xx EPOS and GP EVMMugunthan V N2014-03-04-2/+142
| | | | | | | | | | | | | | | | Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected to RMII and RGMII phy respectively and enable cpsw in config. Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
| * drivers: net: cpsw: add support to have phy address from cpsw platform dataMugunthan V N2014-03-04-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | Some platforms like AM437x have different EVMs with different phy addresses, so this patch adds support for passing phy address via cpsw plaform data. Also renamed phy_id to phy_addr so better understanding of the code. Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> [trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335 pengwyn boards] Signed-off-by: Tom Rini <trini@ti.com>
* | board/ti/am335x/README: update for NAND bootpekon gupta2014-03-03-17/+36
|/ | | | | | | | | NAND boot mode on AM335x EVM has been verified, and steps to use it has been documented and update in this README Signed-off-by: Pekon Gupta <pekon@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Tom Rini <trini@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-02-26-17/+18
|\ | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/armv7/config.mk board/ti/am43xx/mux.c include/configs/am43xx_evm.h Signed-off-by: Tom Rini <trini@ti.com>
| * arm: remove unneeded symbol offsets and _TEXT_BASEAlbert ARIBAUD2014-02-26-4/+0
| | | | | | | | | | | | | | | | Remove the last uses of symbol offsets in ARM U-Boot. Remove some needless uses of _TEXT_BASE. Remove all _TEXT_BASE definitions. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
| * arm: make _end compiler-generatedAlbert ARIBAUD2014-02-26-2/+7
| | | | | | | | | | | | | | | | | | This prevents references to _end from generating absolute relocation records. This change is binary invariant for ARM targets. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
| * ARM: AM43xx: GP-EVM: Correct GPIO used for VTT regulator controlDave Gerlach2014-02-21-11/+11
| | | | | | | | | | | | | | | | | | | | | | Schematic indicates GPIO5_7 is to be used for VTT regulator control rather than GPIO0_21 so modify enable_vtt_regulator to reflect this. Without this some boards will experience DDR3 corruption and fail to boot. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> [trini: Rework patch against mainline] Signed-off-by: Tom Rini <trini@ti.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini2014-02-21-0/+11
|\ \ | |/ |/|
| * am437x_epos_evm: add SPL API, QSPI, and serial flash supportSourav Poddar2014-02-18-0/+11
| | | | | | | | | | | | | | | | Enables support for SPI SPL, QSPI and Spansion serial flash device on the EVM. Configures pin muxes for QSPI mode. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* | ARM: O5/dra7xx: Add SATA boot supportDan Murphy2014-02-19-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | Add the SATA boot support for OMAP5 and dra7xx. Renamed the omap_sata_init to the common init_sata(int dev) for commonality in with sata stack. Added the ROM boot device ID for SATA. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-02-17-681/+1
|\ \
| * | ARM: AM43xx: Enable DDR dynamic IO power down for DDR3Lokesh Vutla2014-01-24-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables dynamically powering down the IO receiver when not performing a read on DDR3 board. This optimizes both active and standby power consumption. This is derived from a patch that is done on AM335x[1] [1] http://arago-project.org/git/projects/?p=u-boot-am33x.git;a=commit;h=6a9ee4bc72ece53fabf01825605fba3d71d5feb2 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * | ARM: OMAP4/5: Remove dead code against CONFIG_SYS_ENABLE_PADS_ALLJassi Brar2014-01-24-680/+0
| |/ | | | | | | | | | | | | | | | | The commit f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls" removed the config option aimed towards moving that stuff into kernel, which renders some code unreachable. Remove that code. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
* | dra7xx_evm: Add CONFIG_SUPPORT_EMMC_BOOT, document usageTom Rini2014-02-07-0/+25
| | | | | | | | | | | | | | | | | | Add a README to the board which lists the commands required to enable booting from the eMMC boot partitions found on the board. Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* | omap5_uevm: Add CONFIG_SUPPORT_EMMC_BOOT, document usageTom Rini2014-02-07-0/+25
|/ | | | | | | | Add a README to the board which lists the commands required to enable booting from the eMMC boot partitions found on the board. Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* ARM: dra7_evm: read mac address properly from e-fuseMugunthan V N2014-01-07-4/+4
| | | | | | | Byte offset of Ethernet mac address read from e-fuse are wrong so DHCP is not working on some boards, modifying the offset to read properly. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* ARM: AM43xx: GP_EVM: Add support for DDR3Lokesh Vutla2013-12-18-3/+98
| | | | | | | | | | | | | | | | GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH). Adding details for the same. Below is the brief description of DDR3 init sequence(SW leveling): -> Enable VTT regulator -> Configure VTP -> Configure DDR IO settings -> Disable initialization and refreshes until EMIF registers are programmed. -> Program Timing registers -> Program leveling registers -> Program PHY control and Temp alert and ZQ config registers. -> Enable initialization and refreshes and configure SDRAM CONFIG register Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
generated by cgit v1.1 at 2024-12-17 20:11:15 +0000