summaryrefslogtreecommitdiff
path: root/board/ti
Commit message (Collapse)AuthorAgeLines
* arm: omap4: panda: Fix checkpatch on panda fileDan Murphy2013-06-18-13/+13
| | | | | | | | Fix the checkpatch warning on the panda.c file for leading spaces. Fix the CHECK warnings on the panda.c file for parenthesis alignment. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* arm: omap4: panda: Add reading of the board revisionDan Murphy2013-06-18-5/+73
| | | | | | | | | | | | | | | | | | | | | | | Detect if we are running on a panda revision A1-A6, or an ES panda board. This can be done by reading the level of GPIOs and checking the processor revisions. This should result in: Panda 4430: GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5 GPIO171, GPIO101, GPIO182: 1 0 1 => A6 Panda ES: GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2 GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3 Set the board name appropriately for the board revision that is detected. Update the findfdt macro to load the a4 device tree binary. Signed-off-by: Dan Murphy <dmurphy@ti.com> [trini: %s/CONTROL_PADCONF_CORE/(*ctrl)->control_padconf_core_base/ and formatting for that] Signed-off-by: Tom Rini <trini@ti.com>
* arm, am33xx: move uart soft reset code to common placeHeiko Schocher2013-06-18-40/+2
| | | | | | | | | | | | | | | move uart soft reset code to common place and call this function from board code, instead of copy and paste this code for every board. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matt Porter <mporter@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Tom Rini <trini@ti.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Tom Rini <trini@ti.com> [trini: Fix igep0033 build, remove 'regval' on pcm051] Signed-off-by: Tom Rini <trini@ti.com>
* arm, am33xx: move rtc32k_enable() to common placeHeiko Schocher2013-06-18-32/+0
| | | | | | | | | | move rtc32k_enable() to common place so all am33xx boards can use it. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matt Porter <mporter@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Tom Rini <trini@ti.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
* arm: Remove OMAP2420H4 and all omap24xx supportTom Rini2013-06-10-1874/+0
| | | | | | | | | The omap2420H4 was the only mainline omap24xx board. Prior to being fixed by Jon Hunter in time for v2013.04 it had been functionally broken for a very long time. Remove this board as there's not been interest in it in U-Boot for quite a long time. Signed-off-by: Tom Rini <trini@ti.com>
* ARM: DRA7xx: Update pinmux dataLokesh Vutla2013-06-10-14/+24
| | | | | | | Updating pinmux data as specified in the latest DM Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com>
* ARM: OMAP2+: Rename asm/arch/clocks.h asm/arch/clock.hLokesh Vutla2013-06-10-3/+3
| | | | | | | To be consistent with other ARM platforms, renaming asm/arch-omap*/clocks.h to asm/arch-omap*/clock.h Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP4+: Cleanup header filesLokesh Vutla2013-06-10-18/+30
| | | | | | | After having the u-boot clean up series, there are many definitions that are unused in header files. Removing all those unused ones. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* am33xx: Board: Make CPSW section of ethernet initialization depend on CPSW ↵Joel A Fernandes2013-06-10-0/+2
| | | | | | | | driver Not doing so breaks cases where CPSW is not required such as for USB RNDIS network boot. Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
* am33xx/omap: Move save_omap_boot_params to omap-common/boot-common.cTom Rini2013-06-05-0/+18
| | | | | | | | | | | We need to call the save_omap_boot_params function on am33xx/ti81xx and other newer TI SoCs, so move the function to boot-common. Only OMAP4+ has the omap_hw_init_context function so add ifdefs to not call it on am33xx/ti81xx. Call save_omap_boot_params from s_init on am33xx/ti81xx boards. Reviewed-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* ARM:Panda:Fix device tree loading for the panda-esDan Murphy2013-05-10-0/+6
| | | | | | | | | | | Fix the device tree loading for panda(4430) and panda-es(4460) Modify the board name if a 4460 panda or panda-es is detected at run time. In the findfdt add a check for the panda-es board name and load the panda-es device tree blob. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* beagleboard: Update comment in get_board_rev()Tom Rini2013-05-10-2/+3
| | | | | | | | We are able to tell the difference between xM Rev Ax/Bx and xM Rev Cx, and have been for some time. The comment above the function however did not list this, so update. Signed-off-by: Tom Rini <trini@ti.com>
* palmas: rename init_settings to an generic palmas initNishanth Menon2013-05-10-1/+1
| | | | | | | Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs, rename twl6035_init_settings with an more generic palmas_init_settings Signed-off-by: Nishanth Menon <nm@ti.com>
* twl6035: rename to palmasNishanth Menon2013-05-10-3/+3
| | | | | | | | | | | TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs Rename twl6035 to palmas to allow reuse across multiple current and future platforms As part of this change, change the CONFIG_TWL6035_POWER to CONFIG_PALMAS_POWER and update usage of header file accordingly. Signed-off-by: Nishanth Menon <nm@ti.com>
* ti814x_evm: enable CPSW supportMatt Porter2013-05-10-0/+108
| | | | | | | | Adds CPSW support to the TI814X EVM configured with an ET1011C PHY in GMII mode. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* am33xx: add pll and clock support for TI814x CPSWMatt Porter2013-05-10-0/+3
| | | | | | | Enables required PLLs and clocks for CPSW on TI814x. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* omap5912-osk: Fix device initialisationJon Hunter2013-04-10-4/+28
| | | | | | | | | | | | | | In the current u-boot, the device pin multiplexing and clock initialisation needs to be early during the boot process and before board_init() is called. U-boot is currently crashing on this board because this is not being done early enough. Therefore, add a s_init() function for the omap5912-osk board to do this. Also fix the stack pointer so that it is pointing to the end of the internal RAM and not the beginning as this was also causing the device to crash. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
* omap5912-osk: Fix booting from NOR flashJon Hunter2013-04-10-6/+6
| | | | | | | | | | | | | The omap5912-osk board is using a RAM based address as the linker location for code. This is causing several problems when attempting to run the latest u-boot code base on this board from flash. Update the default linker location for code to be in NOR flash at address 0x00000000. The omap5912-osk board only has 32MB of RAM and so fix the comment in the omap5912-osk config.mk file as well. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
* omap5912-osk: Fix DRAM initialisationJon Hunter2013-04-10-3/+8
| | | | | | | | | | The size of the DRAM for the omap5912-osk board is getting setup in the dram_init() function. However, for the current u-boot release this is too late and needs to be done in dram_init_banksize(). Therefore, add a dram_init_banksize() function for the omap5912-osk board and setup the DRAM size there. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
* am335x: Update timings for the beaglebone againTom Rini2013-04-10-1/+1
| | | | | | | | After further testing we can run DDR at 400MHz so update the timings again. Tested-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Tom Rini <trini@ti.com>
* ARM: OMAP5: Rename omap5_evm to omap5_uevmSRICHARAN R2013-04-08-0/+0
| | | | | | | | | The omap5-uevm is the reference board name for OMAP5 soc based platform. So rename it accordingly. Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Sricharan R <r.sricharan@ti.com> Tested-by: Nishanth Menon <nm@ti.com>
* omap2420-h4: Fix booting from NOR flashHunter, Jon2013-04-08-15/+2
| | | | | | | | | | | | | | | | The omap2420-h4 board is using a RAM based address as the linker location for code. This is causing several problems when attempting to run the latest u-boot code base on this board from flash. Update the default linker location for code to be in NOR flash. Please note that OMAP maps the NOR flash to address 0x08000000 by default and so use this as the default address for the NOR flash. Also remove legacy code that attempts to calculate where in flash the sdata structure, that holds the memory interface configuration data, is located. By changing the default linker location for code to flash this is no longer necessary. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
* omap2420-h4: Fix DRAM initialisationHunter, Jon2013-04-08-6/+18
| | | | | | | | | | The size of the DRAM for the omap2420-h4 board is getting setup in the dram_init() function. However, for the current u-boot release this is too late and needs to be done in dram_init_banksize(). Therefore, add a dram_init_banksize() function for the omap2420-h4 board and setup the DRAM size there. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
* am335x_evm: Add better timings for the new BeagleBoard DDR3 partTom Rini2013-03-24-1/+38
| | | | | Tested-by: Rao Bodapati <rao@circuitco.com> Signed-off-by: Tom Rini <trini@ti.com>
* ti814x_evm: add ti814x evm board supportMatt Porter2013-03-24-0/+302
| | | | | | | | | | Add TI814X EVM board directory, config file, and MAINTAINERS entry. Enable build. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com> [trini: Adapt to recent omap_hsmmc requirements, Matt re-tested] Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: refactor emif4/ddr to support multiple EMIF instancesMatt Porter2013-03-24-3/+3
| | | | | | | | | | The AM33xx emif4/ddr support closely matches what is need to support TI814x except that TI814x has two EMIF instances. Refactor all the emif4 helper calls and the config_ddr() init function to use an additional instance number argument. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* am33xx: convert defines from am33xx-specific to generic namesMatt Porter2013-03-24-3/+3
| | | | | | | | Eliminate AM33xx specific names to prepare for TI814x support within AM33xx-land. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* am335x: Enable DDR PHY dynamic power down bit for DDR3 boardsVaibhav Hiremath2013-03-24-2/+4
| | | | | | | | | | | | | Enable DDR PHY dynamic power down bit, which enables powering down the IO receiver when not performing read. This also helps in reducing overall power consumption in low power states (suspend/standby). Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com> Cc: Tom Rini <trini@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* arm: dra7xx: Add board files for DRA7XX socsLokesh Vutla2013-03-11-0/+199
| | | | | | | | | | | | | | Adding new board files for DRA7XX socs. The pad registers layout is changed completely from OMAP5 So introducing the new structure here and also adding the minimal data. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishant Kamat <nskamat@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com> [trini: Adapt omap_mmc_init call for last 2 params] Signed-off-by: Tom Rini <trini@ti.com>
* omap3: allow dynamic selection of gfx_formatNikita Kiryanov2013-03-08-2/+4
| | | | | | | | | | | | | | | | | Currently, omap3_dss_panel_config() sets gfx_format to a value that is hardcoded in the code. This forces anyone who wants to use a different gfx_format to make adjustments after calling omap3_dss_panel_config(). This could be avoided if the value of gfx_format were parameterized as input for omap3_dss_panel_config(). Make gfx_format a field in struct panel_config, and update existing structs to set this field to the value that was originally hard coded. Cc: Wolfgang Denk <wd@denx.de> Cc: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* omap_hsmmc: add driver check for write protectionNikita Kiryanov2013-03-08-9/+9
| | | | | | | | Add check for write protection in omap mmc driver. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
* omap_hsmmc: implement driver check for card detectionNikita Kiryanov2013-03-08-14/+9
| | | | | | | Implement driver check for card detection. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* am335x_evm: Add am335x_evm_usbspl build targetTom Rini2013-03-08-1/+1
| | | | | | | We add USB (RNDIS gadget) SPL support as a separate target. We need to pull out YMODEM support in order to be a small enough target binary. Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: enable support for booting via USBIlya Yanok2013-02-18-17/+21
| | | | | | | | | | | | | | | This adds necessary config options and a new build target, am335x_evm_usbspl, to enable usb booting and fixes board_eth_init() function to take into account that we may have USB ether support in SPL now. This uses the same MAC for both cpsw and USB, in order to match ROM behavior. The usbspl build target does not contain UART SPL, CPSW SPL or extra environment settings, so that we may fit within our binary size constraint. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com> Signed-off-by: Tom Rini <trini@ti.com>
* beagle: expansion boards: add LSR COM6L adapterrobertcnelson@gmail.com2013-02-18-0/+6
| | | | | | | | http://www.lsr.com/wireless-products/com6l The eeprom on this expansion board requires 16bit addressing. Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
* beagle: expansion boards: retry i2c_read with 16bit addressingrobertcnelson@gmail.com2013-02-18-0/+8
| | | | | | | Some expansion boards now ship with at24 eeproms that need to communicate via 16bit addressing. Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
* am335x_evm: Fix CPSW ethernet on GP EVM and EVM-SKTom Rini2013-02-12-0/+27
| | | | | | | | In commit cfd4ff6 we implemented part of advisory 1.0.10 (internal delay for RGMII mode not supported). This in turn however requires that we set the tx clock delay feature in the PHY itself. Signed-off-by: Tom Rini <trini@ti.com>
* Add DDR3 support for AM335x-EVM (Version 1.5A)Jeff Lance2013-02-07-0/+41
| | | | | | | | | | | | | | AM335x EVM 1.5A uses Micron MT41J512M8RH-125 SDRAM 4Gb (512Mx8) as the DDR3 chip. [Hebbar Gururaja <gururaja.hebbar@ti.com>] - Resolve merge conflict while rebasing. File structure is changed in the mainline. So re-arrange the code accordingly. - Update commit message to reflect the DDR3 part number Signed-off-by: Jeff Lance <j-lance1@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
* am335x: display msg when reading MAC from efuseLars Poeschel2013-02-07-1/+1
| | | | | | | | When ethaddr is not set in environment the MAC address is read from efuse. The message was only printed in debug case, but this message could be of interest for the ordinary user, so printf it. Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
* Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-01-08-38/+60
|\ | | | | | | | | This required manual merging drivers/mtd/nand/Makefile and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
| * am335x: disable internal delay for RGMII modeYegor Yefremov2012-12-10-1/+1
| | | | | | | | | | | | | | According to errata the AM335x device does not support internal delay mode, so RGMII1_IDMODE and RGMII2_IDMODE must be set to 1. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
| * Pass sdrc timing values through board_sdrc_timings structurePeter Barada2012-12-10-37/+35
| | | | | | | | | | | | | | | | | | Instead of passing individual registers by value to board_get_mem_timings, pass a board_mem_timings structure pointer for the board files to fill in. Pass same structure pointer to write_sdrc_timings. This saves about 90 bytes of space in SPL. Signed-off-by: Peter Barada <peter.barada@logicpd.com>
| * am335x_evm: enable NAND supportIlya Yanok2012-12-10-0/+2
| | | | | | | | | | | | Enable NAND support for AM335X boards. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
| * am335x_evm: add nand pinmux definitionIlya Yanok2012-12-10-0/+22
| | | | | | | | | | | | | | Add NAND pins mux settings for AM335X devices. Enable NAND pins for AM335X EVM board. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* | omap3_beagle: add musb-new initIlya Yanok2012-11-20-0/+43
| | | | | | | | | | | | Add initialization for new MUSB framework. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* | am335x_evm: enable both musb gadget and hostIlya Yanok2012-11-20-2/+21
|/ | | | | | | Enable musb gadget in Ethernet mode on port 0 and musb host on port1. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2012-11-05-1/+108
|\
| * Merge remote-tracking branch 'u-boot-ti/master'Albert ARIBAUD2012-11-03-1/+108
| |\
| | * am335x: add initial AM335x IDK board supportMatthias Fuchs2012-11-02-1/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch extends the am335x_evm board for the AM335x IDK. The IDK board uses MII for the ethernet phy (same as Beaglebone board) and MMC0 for storage (but without card detect line). The IDK uses UART3 for console. So u-boot must be build with CONFIG_SERIAL4 and CONFIG_CONS_INDEX=4 or for the am335x_evm_uart3 board configuration as introduced by Andrew Bradfords recent patch series "am33xx: Enable UART {1,2,3,4,5}...". When using the IDK with console on UART0, those patches are not required. In this case the board slightly needs to be modified. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
| | * am335x: add mux config for DDR3 version of beagleboneKoen Kooi2012-10-30-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes the following boothang in SPL: Unknown board, cannot configure pinmux.### ERROR ### Please RESET the board ### Future commits will add pinmuxes for more on-board peripherals. Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
generated by cgit v1.1 at 2024-11-05 10:22:12 +0000