summaryrefslogtreecommitdiff
path: root/board/ti/dra7xx/mux_data.h
Commit message (Collapse)AuthorAgeLines
* ARM: OMAP5: DRA7xx: Fix misleading comments in mux_data.hLubomir Popov2014-12-04-2/+2
| | | | | | | | | | The comments on the QSPI pad assignments erronously swapped the qspi1_d0 and qspi1_d1 functionality and could cause confusion. QSPI1_D[0] is in fact muxed on pad U1 (gpmc_a16), and QSPI1_D[1] - on pad P3 (gpmc_a17). Fixing comments. Signed-off-by: Lubomir Popov <l-popov@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: DRA: Enable VTT regulatorLokesh Vutla2014-08-25-0/+1
| | | | | | | | | | DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination and this is controlled by gpio7_11. Configuring gpio7_11. The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards, and left unused on previous boards, so it is safe enough to enable gpio on all DRA7 boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* board/ti/dra7xx: add support for parallel NORpekon gupta2014-08-25-2/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM. The Flash device is connected to GPMC controller on chip-select[0] and accessed as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and is CFI compatible. As multiple devices are share GPMC pins on this board, so following board settings are required to detect NOR device: SW5.1 (NAND_BOOTn) = OFF (logic-1) SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */ SW5.3 (eMMC_BOOTn) = OFF (logic-1) SW5.4 (QSPI_BOOTn) = OFF (logic-1) And also set appropriate SYSBOOT configurations: SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */ SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */ SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */ SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */ SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */ SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */ SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */ SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */ Also, following changes are required to enable NOR Flash support in dra7xx_evm board profile:
* board/ti/dra7xx: add support for parallel NANDpekon gupta2014-08-25-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for x16 NAND device (MT29F2G16AAD) connected to GPMC chip-select[0] on DRA7xx EVM. As GPMC pins are shared by multiple devices, so in addition to this patch following board settings are required for NAND device detection [1]: SW5.9 (GPMC_WPN) = OFF (logic-1) SW5.1 (NAND_BOOTn) = ON (logic-0) /* Active-low */ SW5.2 (NOR_BOOTn) = OFF (logic-1) SW5.3 (eMMC_BOOTn) = OFF (logic-1) SW5.4 (QSPI_BOOTn) = OFF (logic-1) And also set appropriate SYSBOOT configurations SW2.1 (SYSBOOT[0]) = ON (logic-1) /* selects NAND Boot */ SW2.2 (SYSBOOT[1]) = OFF (logic-0) /* selects NAND Boot */ SW2.3 (SYSBOOT[2]) = OFF (logic-0) /* selects NAND Boot */ SW2.4 (SYSBOOT[3]) = OFF (logic-0) /* selects NAND Boot */ SW2.5 (SYSBOOT[4]) = ON (logic-1) /* selects NAND Boot */ SW2.6 (SYSBOOT[5]) = ON (logic-1) /* selects NAND Boot */ SW2.7 (SYSBOOT[6]) = OFF (logic-0) /* reserved */ SW2.8 (SYSBOOT[7]) = OFF (logic-0) /* reserved */ SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */ SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */ SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */ SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Addr/Data Muxed */ SW3.5 (SYSBOOT[12])= ON (logic-1) /* device type: Addr/Data Muxed */ SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */ SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */ SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */ Following changes are required in board.cfg to enable NAND on J6-EVM:
* Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2014-07-28-0/+12
|\
| * ARM: DRA7xx: Add cpsw second port pinmuxMugunthan V N2014-07-25-0/+12
| | | | | | | | | | | | Add cpsw second slave port pinmux to use it as primary ethernet port Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* | board: ti: dra7xx: add mux data for UART3Felipe Balbi2014-07-07-0/+5
|/ | | | | | | | | | | | | J6 EVM can be built with UART3 as console, but currently there's nothing muxing UART3 correctly. Likely this only works because, based on commit log, author was only testing with UART3 boot and - I assume - ROM code leave UART3 correctly muxed in that case. If we want to boot from MMC and still use UART3 as console, then we need to mux those signals correctly. Signed-off-by: Felipe Balbi <balbi@ti.com>
* usb: dra7xx: Add support for dra7xx xhci USB hostDan Murphy2013-10-20-0/+1
| | | | | | | | | | | Add the support for the dra7xx xhci usb host. dra7xx does not contain an EHCI controller so the headers can be removed from the board file. The xHCI host on dra7xx is connected to a usb2 phy so need to add support to enable those clocks. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* dra7xx_evm: add SPL API, QSPI, and serial flash supportMatt Porter2013-10-07-0/+10
| | | | | | | | | Enables support for SPI SPL, QSPI and Spansion serial flash device on the EVM. Configures pin muxes for QSPI mode. Signed-off-by: Matt Porter <matt.porter@linaro.org> Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
* ARM: DRA7xx: Add CPSW and MDIO pinmux supportMugunthan V N2013-07-26-0/+14
| | | | | | Adding CPSW Slave 0 and MDIO pinmux support for DRA7xx EVM Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* ARM: DRA7xx: Update pinmux dataLokesh Vutla2013-06-10-14/+24
| | | | | | | Updating pinmux data as specified in the latest DM Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com>
* arm: dra7xx: Add board files for DRA7XX socsLokesh Vutla2013-03-11-0/+47
Adding new board files for DRA7XX socs. The pad registers layout is changed completely from OMAP5 So introducing the new structure here and also adding the minimal data. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishant Kamat <nskamat@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com> [trini: Adapt omap_mmc_init call for last 2 params] Signed-off-by: Tom Rini <trini@ti.com>
generated by cgit v1.1 at 2024-10-13 04:20:15 +0000