summaryrefslogtreecommitdiff
path: root/board/ti/dra7xx/evm.c
Commit message (Collapse)AuthorAgeLines
* arm: omap5: don't enable misc_init_r by defaultFelipe Balbi2014-12-04-12/+0
| | | | | | | | | | Out of all OMAP5-like boards, only one of them needs CONFIG_MISC_INIT_R, so it's best to enable that for that particular board only, instead of enabling for all boards unconditionally. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* OMAP5+: sata/scsi: Implement scsi_init()Roger Quadros2014-10-10-1/+0
| | | | | | | | | | On OMAP platforms, SATA controller provides the SCSI subsystem so implement scsi_init(). Get rid of the unnecessary sata_init() call from dra7xx-evm and omap5-uevm board files. Signed-off-by: Roger Quadros <rogerq@ti.com>
* ARM: DRA: Enable VTT regulatorLokesh Vutla2014-08-25-0/+31
| | | | | | | | | | DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination and this is controlled by gpio7_11. Configuring gpio7_11. The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards, and left unused on previous boards, so it is safe enough to enable gpio on all DRA7 boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2014-07-28-1/+6
|\
| * ARM: dra7_evm: Add Ethernet support for dra72x platformMugunthan V N2014-07-25-1/+6
| | | | | | | | | | | | Set the active_slave to 1 as slave 1 is pinned out in dra72x base board Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* | ARM: DRA7xx: Update the board_name env variableLokesh Vutla2014-07-14-0/+6
|/ | | | | | | Update the board_name env variable and accordingly populate the dtb file. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* dra7xx_evm: Add QSPI_4 support, qspiboot build targetTom Rini2014-04-17-0/+19
| | | | | | | | | | | | We previously only supported QSPI_1 (single) support. Add QSPI_4 (quad) read support as well. This means we can be given one of two boot device values, but don't care which it is, so perform a fixup on the QSPI_4 value. We add a qspiboot build target to better show how you would use QSPI as a boot device in deployment. When we boot from QSPI, we can check the environment for 'boot_os' to control Falcon Mode. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* ARM: DRA7xx: add support for reading cpsw 2nd mac from efuseMugunthan V N2014-03-04-0/+15
| | | | | | | | | Adding support for reading cpsw 2nd mac address from efuse and pass it to kernel via dtb which will be used in dual emac mode of cpsw. Also correct the bit masking of mac id read from the efuse. Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* drivers: net: cpsw: add support to have phy address from cpsw platform dataMugunthan V N2014-03-04-2/+2
| | | | | | | | | | | | Some platforms like AM437x have different EVMs with different phy addresses, so this patch adds support for passing phy address via cpsw plaform data. Also renamed phy_id to phy_addr so better understanding of the code. Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> [trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335 pengwyn boards] Signed-off-by: Tom Rini <trini@ti.com>
* ARM: O5/dra7xx: Add SATA boot supportDan Murphy2014-02-19-1/+2
| | | | | | | | | | | | | Add the SATA boot support for OMAP5 and dra7xx. Renamed the omap_sata_init to the common init_sata(int dev) for commonality in with sata stack. Added the ROM boot device ID for SATA. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* ARM: dra7_evm: read mac address properly from e-fuseMugunthan V N2014-01-07-4/+4
| | | | | | | Byte offset of Ethernet mac address read from e-fuse are wrong so DHCP is not working on some boards, modifying the offset to read properly. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* ARM: dra7_evm: Add SATA supportRoger Quadros2013-12-04-0/+7
| | | | | | | The evm has a SATA port. Enable SATA configuration and inititialize the SATA controller. Signed-off-by: Roger Quadros <rogerq@ti.com>
* usb: dra7xx: Add support for dra7xx xhci USB hostDan Murphy2013-10-20-6/+0
| | | | | | | | | | | Add the support for the dra7xx xhci usb host. dra7xx does not contain an EHCI controller so the headers can be removed from the board file. The xHCI host on dra7xx is connected to a usb2 phy so need to add support to enable those clocks. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* ARM: DRA7xx: Add CPSW support to DRA7xx EVMMugunthan V N2013-07-26-5/+145
| | | | | | Adding support for CPSW Ethernet support found in DRA7xx EVM Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* twl6035: rename to palmasNishanth Menon2013-05-10-1/+1
| | | | | | | | | | | TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs Rename twl6035 to palmas to allow reuse across multiple current and future platforms As part of this change, change the CONFIG_TWL6035_POWER to CONFIG_PALMAS_POWER and update usage of header file accordingly. Signed-off-by: Nishanth Menon <nm@ti.com>
* arm: dra7xx: Add board files for DRA7XX socsLokesh Vutla2013-03-11-0/+103
Adding new board files for DRA7XX socs. The pad registers layout is changed completely from OMAP5 So introducing the new structure here and also adding the minimal data. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishant Kamat <nskamat@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com> [trini: Adapt omap_mmc_init call for last 2 params] Signed-off-by: Tom Rini <trini@ti.com>
generated by cgit v1.1 at 2024-11-07 02:53:54 +0000