summaryrefslogtreecommitdiff
path: root/board/ti/am335x
Commit message (Collapse)AuthorAgeLines
* arm: am33xx: Initialize EMIF REG_PR_OLD_COUNT for BBB and am335x-evmJyri Sarha2016-12-09-0/+28
| | | | | | | | | | | | | | Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2, and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x-evm. With the default values LCDC suffers from DMA FIFO underflows and frame synchronization lost errors. The initialization values are the highest that work flawlessly when heavy memory load is generated by CPU. 32bpp colors were used in the test. On BBB the video mode used 110MHz pixel clock. The mode supported by the panel of am335x-evm uses 30MHz pixel clock. Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: AMx3xx: Make FIT boot as default boot on HS devicesLokesh Vutla2016-12-03-0/+7
| | | | | | | | Verification has to be done before booting any images on HS devices. So default the boot to FIT on HS devices. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: amx3xx: Remove multiple EEPROM readsLokesh Vutla2016-11-21-24/+8
| | | | | | | Detect the board very early and avoid reading eeprom multiple times. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: am335x/mux: Do not hang when encountering a bad EEPROMAlex G2016-11-13-2/+2
| | | | | | | | | | | | | | | | | | | | | In most cases, the SPL and u-boot.img will be on the same boot media. Since the SPL was loaded by the boot rom, the pinmux will already have been configured for this media. This, the board will still be able to boot successfully, or at least reach the u-boot console, where more recovery options are available. I've encountered this on a beaglebone black with a corrupted EEPROM. Removing this check allowed the board to boot successfully. I've also seen this on EVM-based boards with an unprogrammed EEPROM. On those boards, for some reason there were no UART messages. This made it look as if the SOC was dead. Remove the hang(), as it is not a fatal error. Also reformat the error message to be clearer as to the cause. The original message made it appear as if the wrong binary was being loaded. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: am335x: Always set eth/eth1addr environment variableRoger Quadros2016-10-13-26/+46
| | | | | | | | | | | | | Ethernet ports might be used in the kernel even if CPSW driver is disabled at u-boot. So always set ethaddr and eth1addr environment variable from efuse. Retain usbnet_devaddr as it is required for SPL USB eth boot. Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* board: am335x-icev2: add ethernet phy mode detection logicRoger Quadros2016-10-13-7/+75
| | | | | | | | | | | | | | | | | | | Both ethernet ports can be used as CPSW ethernet (RMII mode) or PRU ethernet (MII mode) by setting the jumper near the port. Read the jumper value and set the pinmux, external mux and PHY clock accordingly. As jumper line is overridden by PHY RX_DV pin immediately after bootstrap (power-up/reset), we have to use GPIO edge detection to capture the jumper line status. As u-boot doesn't provide any infrastructure for GPIO edge detection, we directly access the GPIO registers. Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* board: am33xx-hs: Allow post-processing of FIT image on AM33xxAndrew F. Davis2016-10-02-0/+8
| | | | | | | | | | | When CONFIG_FIT_IMAGE_POST_PROCESS or CONFIG_SPL_FIT_IMAGE_POST_PROCESS is enabled board_fit_image_post_process will be called, add this function to am33xx boards when CONFIG_TI_SECURE_DEVICE is set to verify the loaded image. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
* Convert CONFIG_SPL_YMODEM_SUPPORT to KconfigSimon Glass2016-09-16-0/+3
| | | | | | | | Convert CONFIG_SPL_YMODEM_SUPPORT to Kconfig Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SPL_WATCHDOG_SUPPORT to KconfigSimon Glass2016-09-16-0/+3
| | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SPL_ENV_SUPPORT to KconfigSimon Glass2016-09-16-0/+3
| | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* Kconfig: make NOR_BOOT a common optionPeng Fan2016-06-27-9/+0
| | | | | | | | | | | | | | | | Not only am335x supports booting from NOR, i.MX6 SoCs also supports booting from NOR. Make NOR_BOOT a common option to let different SoCs share it. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Christophe Ricard <christophe-h.ricard@st.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Francois Retief <fgretief@spaceteq.co.za> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* board: am335x: Allow to choose serial device dynamicallyLokesh Vutla2016-05-27-0/+11
| | | | | | | | Different AM335x based platforms have different serial consoles. As serial console is Kconfig option a separate defconfig has to be created for each platform. So pass the serial device dynamically. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: dts: AM335x-ICEv2: Add minimal dts supportLokesh Vutla2016-05-27-0/+2
| | | | | | | | Add minimal dts support for AM335x-ICEv2 board Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com>
* board: AM335x-ICEv2: Add cpsw supportLokesh Vutla2016-05-27-7/+80
| | | | | | | | | | | | | | | | | | | | | | In order to enable cpsw on AM335x ICEv2 board, the following needs to be done: 1)There are few on board jumper settings which gives a choice between cpsw and PRUSS, that needs to be properly selected[1]. Even after selecting this, there are few GPIOs which control these muxes that needs to be held high. 2) The clock to PHY is provided by a PLL-based clock synthesizer[2] connected via I2C. This needs to properly programmed and locked for PHY operation. And PHY needs to be reset before before being used, which is also held by a GPIO. 3) RMII mode needs to be selected. [1] http://www.ti.com/lit/zip/tidr336 [2] http://www.ti.com/lit/ds/symlink/cdce913.pdf Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* board: AM335x-ICEv2: Add DDR dataLokesh Vutla2016-05-27-1/+40
| | | | | | | | | AM335x ICEv2 contains a 2Gbit(128Mx16) of DDR3 SDRAM(MT41J128M16JT-125), capable of running at 400MHz. Adding this specific DDR configuration details running at 400MHz. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* board: AM335x-ICEv2: Add pinmux supportLokesh Vutla2016-05-27-0/+31
| | | | | | | Add necessary pinmux support for AM335x ICEv2 board. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* board: AM335x-ICEv2: Add epprom supportLokesh Vutla2016-05-27-0/+5
| | | | | | | | | Similar to other TI's AM335x platforms, AM335x ICEv2 also has an eeprom populated for its unique identification. Adding this info so that AM335x ICEv2 specific initialization can be done. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: dts: AM335x-BBG: Add initial supportLokesh Vutla2016-05-27-0/+2
| | | | | | | Add initial DTS support for AM335x-BBG Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: dts: AM335x-evmsk: Add initial supportLokesh Vutla2016-05-27-0/+2
| | | | | | | Add initial DTS support for AM335x-evm sk. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: AM335x: Enable FITLokesh Vutla2016-05-27-1/+0
| | | | | | | Use a single defconfig for all AM335x platforms by enabling FIT Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: am33xx: fit: add support for selecting dtb dynamicallyLokesh Vutla2016-05-27-0/+14
| | | | | | | | FIT allows for a multiple dtb in a single image. SPL needs a way to detect the right dtb to be used. Adding support for the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* efi_loader: Add runtime servicesAlexander Graf2016-03-15-0/+30
| | | | | | | | | | | | | | | | | After booting has finished, EFI allows firmware to still interact with the OS using the "runtime services". These callbacks live in a separate address space, since they are available long after U-Boot has been overwritten by the OS. This patch adds enough framework for arbitrary code inside of U-Boot to become a runtime service with the right section attributes set. For now, we don't make use of it yet though. We could maybe in the future map U-boot environment variables to EFI variables here. Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* ti: AM335x: Use generic EEPROM detection logicNishanth Menon2016-03-14-120/+59
| | | | | | | | | | Use the generic EEPROM detection logic instead of duplicating the AM eeprom logic. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Steven Kipisz <s-kipisz2@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board/ti/am335x: add support for BeagleBone Greenrobertcnelson@gmail.com2015-11-18-3/+9
| | | | | | | | | | | | | | | | | | | | | SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus the HDMI port and addition of two Grove connectors (i2c2 and usart2). This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom: 1A: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|] http://beagleboard.org/green http://www.seeedstudio.com/wiki/Beaglebone_green In Mainline Kernel as of: https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=79a4e64c679d8a0b1037da174e4aea578c80c4e6 Patch tested on BeagleBone Black (rev C) and BeagleBone Green (production model) Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board/ti/am335x: beaglebone stop muxing i2c1_pin_muxrobertcnelson@gmail.com2015-11-12-2/+0
| | | | | | | | | | | On the BeagleBone these i2c1 pins are routed to the expanasion header, where they can be defined as either pr1_usart0_Xxd/pwm0/spi0/i2c1, dont assume i2c1 Fixes: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/313894/1387696 Signed-off-by: Robert Nelson <robertcnelson@gmail.com> Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com> CC: Tom Rini <trini@konsulko.com>
* board/ti: Update MAINTAINERS entries with more boardsTom Rini2015-11-10-0/+1
| | | | | | | A few config files have been added without updating MAINTAINERS. Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: AM335x: mux: change mmc0 cd pinmux from mmc0_sdcd to gpioMugunthan V N2015-10-22-1/+1
| | | | | | | | | | Currently omap_hsmmc driver doesn't use sdcd pin to detect whether the card is present or not. Instead the same pin is used as GPIO to detect card presence. So change the pin mux mode from mmc0_sdcd to gpio0_6. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* am335x_evm: prepare for eth driver model supportMugunthan V N2015-10-22-0/+7
| | | | | | | | Prepare board file so that ethernet registration are commented for DM conversion Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* usb: musb-new: CONFIG_MUSB prefix replacement with CONFIG_USB_MUSBPaul Kocialkowski2015-08-05-1/+1
| | | | | | | | | USB-related options are usually prefixed with CONFIG_USB and platform-specific adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for consistency. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* net: cosmetic: Name ethaddr variables consistentlyJoe Hershberger2015-04-18-3/+3
| | | | | | | | Use "_ethaddr" at the end of variables and drop CamelCase. Make constant values actually 'const'. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Simon Glass <sjg@chromium.org>
* dm: select CONFIG_DM* optionsMasahiro Yamada2015-04-18-9/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As mentioned in the previous commit, adding default values in each Kconfig causes problems because it does not co-exist with the "depends on" syntax. (Please note this is not a bug of Kconfig.) We should not do so unless we have a special reason. Actually, for CONFIG_DM*, we have no good reason to do so. Generally, CONFIG_DM is not a user-configurable option. Once we convert a driver into Driver Model, the board only works with Driver Model, i.e. CONFIG_DM must be always enabled for that board. So, using "select DM" is more suitable rather than allowing users to modify it. Another good thing is, Kconfig warns unmet dependencies for "select" syntax, so we easily notice bugs. Actually, CONFIG_DM and other related options have been added without consistency: some into arch/*/Kconfig, some into board/*/Kconfig, and some into configs/*_defconfig. This commit prefers "select" and cleans up the following issues. [1] Never use "CONFIG_DM=n" in defconfig files It is really rare to add "CONFIG_FOO=n" to disable CONFIG options. It is more common to use "# CONFIG_FOO is not set". But here, we do not even have to do it. Less than half of OMAP3 boards have been converted to Driver Model. Adding the default values to arch/arm/cpu/armv7/omap3/Kconfig is weird. Instead, add "select DM" only to appropriate boards, which eventually eliminates "CONFIG_DM=n", etc. [2] Delete redundant CONFIGs Sandbox sets CONFIG_DM in arch/sandbox/Kconfig and defines it again in configs/sandbox_defconfig. Likewise, OMAP3 sets CONFIG_DM arch/arm/cpu/armv7/omap3/Kconfig and defines it also in omap3_beagle_defconfig and devkit8000_defconfig. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* malloc_f: enable SYS_MALLOC_F by default if DM is onMasahiro Yamada2015-03-28-3/+0
| | | | | | | | | | | | | | This option has a bool type, not hex. Fix it and enable it if CONFIG_DM is on because Driver Model always requires malloc memory. Devices are scanned twice, before/after relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc memory before relocation. As it is board-independent, handle it globally. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Robert Baldyga <r.baldyga@samsung.com>
* malloc_f: remove redundant defalut values of CONFIG_SYS_MALLOC_F_LENMasahiro Yamada2015-03-28-3/+0
| | | | | | | | | | The default value of CONFIG_SYS_MALLOC_F_LEN is defined by ./Kconfig as 0x400. Each defconfig or Kconfig need not repeat the same value. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Robert Baldyga <r.baldyga@samsung.com>
* MAINTAINERS, git-mailrc: Update my email addressTom Rini2015-03-02-6/+1
| | | | Signed-off-by: Tom Rini <trini@konsulko.com>
* kconfig: remove unneeded dependency on !SPL_BUILDMasahiro Yamada2015-02-24-5/+5
| | | | | | | Now CONFIG_SPL_BUILD is not defined in Kconfig, so "!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to KconfigSimon Glass2015-02-12-0/+6
| | | | | Move this option to Kconfig and update all boards. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: omap3: Move driver model CONFIGs to KconfigSimon Glass2015-02-12-0/+10
| | | | | | | Remove driver model CONFIGs from the board config headers and use Kconfig instead. Signed-off-by: Simon Glass <sjg@chromium.org>
* doc: fix spelling errors in am335x/READMEJeremiah Mahler2015-01-08-3/+3
| | | | | | | Fix several spelling errors and replace the invalid word "architectured" with "designed". Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
* am335x_evm: Convert NOR_BOOT to KconfigTom Rini2014-11-05-0/+8
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Add NOR to KconfigTom Rini2014-11-05-0/+7
| | | | | | | Make enabling support for NOR (and describe where it's seen) be done via Kconfig. Signed-off-by: Tom Rini <trini@ti.com>
* kconfig: arm: introduce symbol for ARM CPUsGeorges Savoundararadj2014-10-29-3/+0
| | | | | | | | | | | | | | | | | This commit introduces a Kconfig symbol for each ARM CPU: CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136, CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100. Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected for CPU_ARM1176 and CPU_V7. For each target, the corresponding CPU is selected and the definition of SYS_CPU in the corresponding Kconfig file is removed. Also, it removes redundant "string" type in some Kconfig files. Signed-off-by: Georges Savoundararadj <savoundg@gmail.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
* am335x_boneblack: Only modify NAND/NOR/MMC1 pinmux on BBB in boneblack builds.Tom Rini2014-10-23-2/+2
| | | | | | | | | | In the case of Beaglebone Black we only want to set the NAND or NOR cape pinmux when the config has been specifically modified by the user for this non-default case. Make the default be to set the MMC1 (eMMC) pinmux. We don't need similar changes for Beaglebone White as there is nothing on MMC1 by default there. Signed-off-by: Tom Rini <trini@ti.com>
* kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada2014-09-13-5/+0
| | | | | | | | | | | | | | | | | | Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* arm: am335x: add Kconfig range attribute to prevent invalid CONS_INDEXMasahiro Yamada2014-09-04-0/+1
| | | | | | | | The help message in board/ti/am335x/Kconfig says AM335x has 6 UARTs, so the valid number for CONFIG_CONS_INDEX is from 1 to 6. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com>
* am335x_evm: Convert CONFIG_CONS_INDEX into a menu choiceTom Rini2014-08-25-18/+17
| | | | | | | | | | - Drop CONFIG_SERIAL[1-6] and use CONFIG_CONS_INDEX tests instead - Add choice and help text to board/ti/am335x/Kconfig - Correct comment about IDK in board/ti/am335x/mux.c - Remove am335x_evm_uart* defconfig files as they're just variations on a config option now. Signed-off-by: Tom Rini <trini@ti.com>
* board/ti/am335x: add support for beaglebone NOR Capepekon gupta2014-08-25-60/+35
| | | | | | | | | | | | | This patch adds support of NOR cape[1] for both Beaglebone (white) and Beaglebone(Black) boards. NOR Flash on this cape is connected to GPMC chip-select[0] and accesses as external memory-mapped device. This cape has 128Mbits(16MBytes), x16, CFI compatible NOR Flash device. As GPMC chip-select[0] can be shared by multiple capes so NOR profile is not enabled by default in boards.cfg. Following changes are required to enable NOR cape detection when building am335x_boneblack board profile. Signed-off-by: Tom Rini <trini@ti.com>
* board/ti/am335x: add support for beaglebone NAND capepekon gupta2014-08-25-20/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beaglebone Board can be connected to expansion boards to add devices to them. These expansion boards are called 'capes'. This patch adds support for following versions of Beaglebone(AM335x) NAND capes (a) NAND Device with bus-width=16, block-size=128k, page-size=2k, oob-size=64 (b) NAND Device with bus-width=16, block-size=256k, page-size=4k, oob-size=224 Further information and datasheets can be found at [1] and [2] * How to boot from NAND using Memory Expander + NAND Cape ? * - Important: As BOOTSEL values are sampled only at POR, so after changing any setting on SW2 (DIP switch), disconnect and reconnect all board power supply (including mini-USB console port) to POR the beaglebone. - Selection of ECC scheme for NAND cape(a), ROM code expects BCH8_HW ecc-scheme for NAND cape(b), ROM code expects BCH16_HW ecc-scheme - Selction of boot modes can be controlled via DIP switch(SW2) present on Memory Expander cape. SW2[SWITCH_BOOT] == OFF follow default boot order MMC-> SPI -> UART -> USB SW2[SWITCH_BOOT] == ON boot mode selected via DIP switch(SW2) So to flash NAND, first boot via MMC or other sources and then switch to SW2[SWITCH_BOOT]=ON to boot from NAND Cape. - For NAND boot following switch settings need to be followed SW2[ 1] = OFF (SYSBOOT[ 0]==1: NAND boot mode selected ) SW2[ 2] = OFF (SYSBOOT[ 1]==1: -- do -- ) SW2[ 3] = ON (SYSBOOT[ 2]==0: -- do -- ) SW2[ 4] = ON (SYSBOOT[ 3]==0: -- do -- ) SW2[ 5] = OFF (SYSBOOT[ 4]==1: -- do -- ) SW2[ 6] = OFF (SYSBOOT[ 8]==1: 0:x8 device, 1:x16 device ) SW2[ 7] = ON (SYSBOOT[ 9]==0: ECC done by ROM ) SW2[ 8] = ON (SYSBOOT[10]==0: Non Muxed device ) SW2[ 9] = ON (SYSBOOT[11]==0: -- do -- ) [1] http://beagleboardtoys.info/index.php?title=BeagleBone_Memory_Expansion [2] http://beagleboardtoys.info/index.php?title=BeagleBone_4Gb_16-Bit_NAND_Module *IMPORTANT NOTE* As Beaglebone board shares the same config as AM335x EVM, so following changes are required in addition to this patch for Beaglebone NAND cape. (1) Enable NAND in am335x_beaglebone board profile (2) Add CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config because: - AM335x EVM has NAND device with datawidth=8, whereas - Beaglebone NAND cape has NAND device with data-width=16
* Add board MAINTAINERS filesMasahiro Yamada2014-07-30-0/+17
| | | | | | | | | | | | | | | | | | | | We have switched to Kconfig and the boards.cfg file is going to be removed. We have to retrieve the board status and maintainers information from it. The MAINTAINERS format as in Linux Kernel would be nice because we can crib the scripts/get_maintainer.pl script. After some discussion, we chose to put a MAINTAINERS file under each board directory, not the top-level one because we want to collect relevant information for a board into a single place. TODO: Modify get_maintainer.pl to scan multiple MAINTAINERS files. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
* kconfig: add board Kconfig and defconfig filesMasahiro Yamada2014-07-30-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* am335x_evm / gumstix pepper: Correct DDR settingsTom Rini2014-07-25-27/+3
| | | | | | | | | | | | | | As noted by clang, we have been shifting certain values out of 32bit range when setting some DDR registers. Upon further inspection these had been touching reserved fields (and having no impact). These came in from historical bring-up code and can be discarded. Similarly, we had been declaring some fields as 0 when they will be initialized that way. Tested on Beaglebone White. Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Ash Charles <ash@gumstix.com> Signed-off-by: Tom Rini <trini@ti.com> Tested-By: Ash Charles <ashcharles@gmail.com>
generated by cgit v1.1 at 2024-11-07 23:41:26 +0000