summaryrefslogtreecommitdiff
path: root/board/sunxi
Commit message (Collapse)AuthorAgeLines
* sunxi: Add support for Cubieboard4Chen-Yu Tsai2016-10-30-0/+5
| | | | | | | | | | | | The Cubieboard4 is an A80 SoC based development board from Cubietech. This board has a UART port, 4 USB host ports, a USB 3.0 OTG connector, HDMI and VGA outputs, a micro SD slot, 8G eMMC flash, 2G DRAM, a WiFi/BT combo chip, headphone and microphone jacks, IR receiver, and GPIO headers. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Enable SPL support for A80 Optimus boardChen-Yu Tsai2016-10-30-0/+5
| | | | | | | | | | | | | | | | The A80 Optimus Board was launched with the Allwinner A80 SoC. It was jointly developed by Allwinner and Merrii. This board has a UART port, a JTAG connector, 2 USB host ports, a USB 3.0 OTG connector, an HDMI output, a micro SD slot, 16G eMMC flash, 2G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone jack, IR receiver, and additional GPIO headers. Signed-off-by: Chen-Yu Tsai <wens@csie.org> [hdegoede@redhat.com: update existing Merrii_A80_Optimus_defconfig instead of adding a new defconfig] Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Add default zq value for sun9i (A80)Chen-Yu Tsai2016-10-30-0/+1
| | | | | | | | | Both the A80 Optimus board and the Cubieboard 4 use a zq value of 4145117, or 0x3f3fdd. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Set default CPU clock rate to 1008 MHz for sun9i (A80)Chen-Yu Tsai2016-10-30-1/+1
| | | | | | | | In Allwinner's SDK the A80 is clocked to 1008 MHz by default. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: add MMC pinmux setup for SDC2 on sun9iPhilipp Tomsich2016-10-30-0/+7
| | | | | | | | The A80 can support 8-bit eMMC with reset on the PC pingroups. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: enable SPL for sun9iPhilipp Tomsich2016-10-30-0/+1
| | | | | | | | | | Now that DRAM initialization and clock setup is supported, we can enable SPL for the A80. [wens@csie.org: Added commit message] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: DRAM initialisation for sun9iPhilipp Tomsich2016-10-30-2/+4
| | | | | | | | | | | | | | | This adds DRAM initialisation code for sun9i, which calculates the appropriate timings based on timing information for the supplied DDR3 bin and the clock speeds used. With this DRAM setup, we have verified DDR3 clocks of up to 792MHz (i.e. DDR3-1600) on the A80-Q7 using a dual-channel configuration. [wens@csie.org: Moved dram_sun9i.c to arch/arm/mach-sunxi/; style cleanup] Signed-off-by: Chen-Yu Tsai <wens@csie.org> [hdegoede@redhat.com: Drop some huge non-documenting #if 0 ... #endif blocks] [hdegoede@redhat.com: Fix checkpatch warnings] Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* Convert CONSOLE_PRE_CONSOLE_BUFFER options to KconfigSimon Glass2016-10-23-0/+3
| | | | | | | Move these option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jteki@openedev.com>
* Kconfig: Move config IDENT_STRING to KconfigSiva Durga Prasad Paladugu2016-09-20-0/+3
| | | | | | | | | Move the config IDENT_STRING to Kconfig and migrate all boards [sivadur: Migrate zynq boards] Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> [trini: Update configs, add some default to sunxi Kconfig] Signed-off-by: Tom Rini <trini@konsulko.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-sunxiTom Rini2016-09-18-0/+5
|\
| * sunxi: Add defconfig and dts for the NanoPi NEOJelle van der Waa2016-09-18-0/+5
| | | | | | | | | | | | | | | | | | The NanoPi NEO is a simple h3 board with 512MB RAM, ethernet, one usb and one usb OTG connector. Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | Convert CONFIG_SPL_SERIAL_SUPPORT to KconfigSimon Glass2016-09-16-0/+3
| | | | | | | | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* | Convert CONFIG_SPL_POWER_SUPPORT to KconfigSimon Glass2016-09-16-0/+3
| | | | | | | | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* | Convert CONFIG_SPL_MMC_SUPPORT to KconfigSimon Glass2016-09-16-0/+3
| | | | | | | | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* | Convert CONFIG_SPL_LIBGENERIC_SUPPORT to KconfigSimon Glass2016-09-16-0/+3
| | | | | | | | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* | Convert CONFIG_SPL_LIBDISK_SUPPORT to KconfigSimon Glass2016-09-16-0/+3
| | | | | | | | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* | Convert CONFIG_SPL_LIBCOMMON_SUPPORT to KconfigSimon Glass2016-09-16-0/+3
| | | | | | | | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* | Convert CONFIG_SPL_GPIO_SUPPORT to KconfigSimon Glass2016-09-16-0/+3
|/ | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* ARM: armv7: move CONFIG_ARMV7_PSCI to KconfigMasahiro Yamada2016-09-07-0/+5
| | | | | | | | | Add ARCH_SUPPORT_PSCI as a non-configurable option that platforms can select. Then, move CONFIG_ARMV7_PSCI, which is automatically enabled if both ARMV7_NONSEC and ARCH_SUPPORT_PSCI are enabled. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* sunxi: fix 64-bit compiler warning for SPL header parsingAndre Przywara2016-09-06-1/+1
| | | | | | | | | | Casting "int"s to pointers is only valid for 32-bit systems. Add the appropriate pointer type cast to avoid a compiler warning when compiling for AArch64. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Kconfig: rename non-existent SUN50I_A64 config symbolAndre Przywara2016-09-06-1/+1
| | | | | | | | | There is no "CONFIG_MACH_SUN50I_A64" in upstream U-Boot, so fix the name to prevent the option to be enabled. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Add defconfig and dts file for the Orange Pi Plus2E SBCHans de Goede2016-09-03-0/+1
| | | | | | | | | | | The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus, with 2G RAM and an external gbit ethernet phy. The dts file is identical to the one submitted to the upstream kernel, except that it has the pending patch to enable the ethernet controller squashed in, as u-boot already has sun8i-emac support. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Add support for A33-OLinuXino boardStefan Mavrodiev2016-09-03-0/+5
| | | | | | | | | | | | | | | | | A33-OLinuXino is A33 development board designed by Olimex LTD. It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector, headphone and mic jacks, connector for LiPo battery and optional 4GB NAND Flash. It has two 40-pin headers. One for LCD panel, and one for additional modules. Also there is CSI/DSI connector. The dts files are identical to the ones submitted to the upstream kernel. Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Add iNet D978 rev2 defconfigIcenowy Zheng2016-09-03-0/+5
| | | | | | | | | | The iNet D978 rev2 is a tablet board designed by iNet, which is intended to use on 10" tablets with a appearance like Apple iPad. It has A33 SoC, 1GB RAM, 8GB/16GB NAND, SDIO Wi-Fi, a MicroUSB port and a MicroSD slot. Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sun5i: Add defconfig and dts file for the Empire Electronix M712 tabletHans de Goede2016-08-26-0/+1
| | | | | | | | | | | Add a defconfig and dts file for the Empire Electronix M712 tablet, this is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV wifi chip and a DMART06 (1238a4) accelerometer. The dts file is identical to the one submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sun6i: Add defconfig and dts file for tablets using the inet-q972 PCBHans de Goede2016-08-26-0/+1
| | | | | | | | | | | | | | | Add a defconfig and dts file for tablets using the generic inet-q972 PCB. Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host, micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot, (mini) power-barrel and an usb wifi module. This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet. The dts files are identical to the ones submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* kconfig: use bool instead of boolean for type definition attributesMasahiro Yamada2016-08-12-8/+8
| | | | | | | | | | Linux stopped the use of keyword 'boolean' in Kconfig. Refer to commit 6341e62b212a2541efb0160c470e90bd226d5496 ("kconfig: use bool instead of boolean for type definition attributes") in Linux Kernel. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* sunxi: On newer SoCs use words 1-3 instead of just word 3 from the SIDHans de Goede2016-07-31-1/+19
| | | | | | | | | | | | | | | | It seems that bytes 13-14 of the SID / bytes 1-2 from word 3 of the SID are always 0 on H3 making it a poor candidate to use as source for the serialnr / mac-address, and the other non constant words (1 and 2) also have quite a few bits which are the same for some boards, This commits switches to using the crc32 of words 1 - 3 to get a more unique value for the mac-address / serialnr. Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Ensure that the NIC specific bytes of the mac are not all 0Hans de Goede2016-07-31-0/+4
| | | | | | | | | | | | | | On 2 of my H3 boards bytes 13-15 of the SID are all 0 leading to the NIC specific bytes of the mac all being 0, which leads to the boards not getting an ipv6 address from the dhcp server. This commits adds a check to ensure this does not happen. Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add defconfig and dts file for the Orange Pi PC Plus SBCHans de Goede2016-07-26-0/+1
| | | | | | | | | | | | | | | There is a new Orange Pi PC *Plus* version available now, this is an extended version of the regular Orange Pi PC with sdio wifi and an eMMC. The upstream kernel devs have decided that they want a separate dts for the PC Plus rather then sharing a single dts between the regular PC and the PC Plus. So add a new orangepi_pc_plus_defconfig to match. The added dts file matches the one submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* mtd: nand: Add the sunxi NAND controller driverBoris Brezillon2016-07-24-1/+4
| | | | | | | | | | | We already have an SPL driver for the sunxi NAND controller, now add the normal/standard one. The source has been copied from Linux 4.6 with a few changes to make it work in u-boot. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Add defconfig and dts file for the Orange Pi Lite SBCHans de Goede2016-07-15-0/+1
| | | | | | | | | | | The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM, micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector, sdio attached rtl8189ftv wifi and an ir receiver. The dts file is identical to the one submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Use BROM stored boot_media value to determine our boot-sourceHans de Goede2016-07-15-2/+1
| | | | | | | | | Now that we know that the BROM stores a value indicating the boot-source at the beginning of SRAM, use that instead of trying to recreate the BROM's boot probing. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Remove some unnecessary #ifdefsHans de Goede2016-07-15-9/+2
| | | | | | | | | | | | We always define CONFIG_MISC_INIT_R on sunxi and misc_init_r is never called in the spl, so the linker will optimize it and parse_spl_header(), of which it is the only caller, away. On the tests I've done (Orange Pi PC build) the SPL actually becomes 8 bytes smaller with this patch. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add support for multiple ethadrr-essesHans de Goede2016-07-15-16/+47
| | | | | | | | | | | | | | | | Currently we fill ethaddr with a fixed unique address based on the SoCs serial (from the sid) to make sure that boards which use the integrated emac / gmac get a fixed mac rather then a random one. On some boards the wifi does not come with a fixed mac either, so we need to also set eth1addr. This commit changes the ethaddr setting code to check for ethernet%d aliases (as fdt_fixup_ethernet does) and set an ethaddr variable for all present aliases. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: FEL - Add the ability to recognize and auto-import uEnv-style dataBernhard Nortmann2016-07-15-8/+21
| | | | | | | | | | | | | | | | | | | | | | | | The patch converts one of the "reserved" fields in the sunxi SPL header to a fel_uEnv_length entry. When booting over USB ("FEL mode"), this enables the sunxi-fel utility to pass the string length of uEnv.txt compatible data; at the same time requesting that this data be imported into the U-Boot environment. If parse_spl_header() in the sunxi board.c encounters a non-zero value in this header field, it will therefore call himport_r() to merge the string (lines) passed via FEL into the default settings. Environment vars can be changed this way even before U-Boot will attempt to autoboot - specifically, this also allows overriding "bootcmd". With fel_script_addr set and a zero fel_uEnv_length, U-Boot is safe to assume that data in .scr format (a mkimage-type script) was passed at fel_script_addr, and will handle it using the existing mechanism ("bootcmd_fel"). Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* doc: ARMv8: add README.pine64Andre Przywara2016-07-11-0/+98
| | | | | | | | | | | | Since we lack information about the DRAM initialization for the Allwinner A64 SoC, booting any A64 based board like the Pine64 is a bit involved at the moment. Add a README file to explain the process. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Move to board/sunxi/ from doc/] Signed-off-by: Tom Rini <trini@konsulko.com>
* sunxi: Add defconfig and DTS file for Allwinner R16 EVB (Parrot)Quentin Schulz2016-07-02-0/+5
| | | | | | | | | | | | | | | The Parrot Board is an evaluation board with an Allwinner R16 (assumed to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2 controllable buttons, an LVDS port with separated backlight and capacitive touch panel ports, an audio/microphone jack, a camera CSI port, 2 sets of 22 GPIOs and an accelerometer. The DTS file is identical to the one submitted to the upstream kernel. Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: spl: Fix DRAM info printingHans de Goede2016-07-02-1/+1
| | | | | | | | | | | The switch to simple_printf was causing the SPL dram info to show as: DRAM: u MiB This fixes this by switching from %lu to %d for printing the DRAM size. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Revert "sunxi: make SoC variant choice mandatory"Hans de Goede2016-06-20-0/+1
| | | | | | | | | | | | | | | | | This reverts commit 1a5f0de08e86("sunxi: make SoC variant choice mandatory"). With the optional marking in the Kconfig "make savedefconfig" will drop CONFIG_MACH_SUN4I=y from all the A10 boards, making it hard to see at a glance which family of sunxi chips the defconfig is for. This commit therefore restores the optional, and restores CONFIG_MACH_SUN4I=y to all defconfig's which had it dropped because of this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add defconfig and dts file for inet86dz boardHans de Goede2016-06-20-0/+1
| | | | | | | | | | | | | | | The inet86dz board is a board used in 7" tablets from various oems. These tablets are a23 based 7" tablets featuring a 1024x600 LCD, 512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector which doubles as charging port. The dts file this commit adds is identical to the one submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add defconfig and dts file for Polaroid MID2407PXE03 tabletHans de Goede2016-06-20-0/+1
| | | | | | | | | | | | The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0 PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680 touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector which doubles as charging port. The dts file is identical to the one submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Enable a bunch of commands by default on sunxiHans de Goede2016-05-25-0/+7
| | | | | | | | | | | | | Recently a set of CONFIG_CMD_FOO defines was moved from being defined in config_distro_defaults to Kconfig, and added to all sunxi defconfigs to compensate. Instead of explictly selecting these in all sunxi defconfigs, simply always select these for sunxi boards. This makes the defconfigs simpler and ensures a consistent set of available commands across all sunxi boards. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* Revert "sunxi: Reserve ATF memory space on A64"Andre Przywara2016-05-25-9/+0
| | | | | | | | | | | The ARM Trusted Firmware (ATF) code now lives in SRAM on the Pine64/A64, so we can claim the whole of DRAM for OS use. This reverts commit 3ffe39ed2b66af71c7271d0cef2a248b5bf7dfdb. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: power: add AXP809 supportChen-Yu Tsai2016-05-25-5/+15
| | | | | | | | The A80 uses the AXP809 as its primary PMIC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: power: axp818: Add support for switch SWChen-Yu Tsai2016-05-25-0/+1
| | | | | | | | | The AXP818 has a switchable output, SW. This is commonly used for controlling power to the LCD backlight. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Disable VIDEO for SoCs without display supportChen-Yu Tsai2016-05-25-1/+1
| | | | | | | | The newer chips use a newer display pipeline, which is not supported. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Add default MMC0 card detect pin for A83T, H3 and A64 SoCsChen-Yu Tsai2016-05-25-0/+1
| | | | | | | | | A83T, H3, and A64 have a dedicated pin for card detect on the PF pingroup. This is used in all designs. Set it as the default. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Sort SoC variants by family (sunXi) first, chip name secondChen-Yu Tsai2016-05-25-11/+11
| | | | | | | | | In most other places, we sort SoC descriptions by family (sunXi) first, then by the chip name (A20). Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: make SoC variant choice mandatoryChen-Yu Tsai2016-05-25-1/+0
| | | | | | | | | The user should always select an SoC variant to support. Not choosing one doesn't make sense for a bootloader. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
generated by cgit v1.1 at 2024-11-10 06:49:58 +0000