summaryrefslogtreecommitdiff
path: root/board/sbc8641d/sbc8641d.c
Commit message (Collapse)AuthorAgeLines
* 86xx: Reset updatePeter Tyser2009-02-16-0/+29
| | | | | | | | | | Update the 86xx reset sequence to try executing a board-specific reset function. If the board-specific reset is not implemented or does not succeed, then assert #HRESET_REQ. Using #HRESET_REQ is a more standard reset procedure than the previous method and allows all board peripherals to be reset if needed. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* sbc8641d: Fix PCI mapping conceptsBecky Bruce2009-01-13-4/+4
| | | | | | | | | Rename _BASE to _BUS, as it's actually a PCI bus address, separate virtual and physical addresses into _VIRT and _PHYS, and use each appopriately. This makes the code easier to read and understand, and facilitates mapping changes going forward. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
* Coding Style cleanup, update CHANGELOGWolfgang Denk2008-11-02-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* 86xx: remove the unused ddr_enable_ecc in the board fileDave Liu2008-10-30-11/+0
| | | | | | | | | The DDR controller of 86xx processors have the ECC data init feature, and the new DDR code is using the feature, we don't need the way with DMA to init memory again. Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Kumar Gala <kumar.gala@freescale.com>
* 86xx: Convert all fsl_pci_init users to new APIsKumar Gala2008-10-24-37/+18
| | | | | | | | | | | | Converted MPC8610HCPD, MPC8641HPCN, and SBC8641D to use fsl_pci_setup_inbound_windows() and ft_fsl_pci_setup(). With these changes the board code is a bit smaller and we get dma-ranges set in the device tree for these boards. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com> Acked-by: Jon Loeliger <jdl@freescale.com>
* rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD2008-10-18-70/+70
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* FSL DDR: Convert SBC8641D to new DDR code.Kumar Gala2008-08-27-3/+2
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Change initdram() return type to phys_size_tBecky Bruce2008-06-12-1/+1
| | | | | | | | | | | | | | | | | | | This patch changes the return type of initdram() from long int to phys_size_t. This is required for a couple of reasons: long int limits the amount of dram to 2GB, and u-boot in general is moving over to phys_size_t to represent the size of physical memory. phys_size_t is defined as an unsigned long on almost all current platforms. This patch *only* changes the return type of the initdram function (in include/common.h, as well as in each board's implementation of initdram). It does not actually modify the code inside the function on any of the platforms; platforms which wish to support more than 2GB of DRAM will need to modify their initdram() function code. Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc MPC8641HPCN. Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* 85xx/86xx: Rename ext_refrec to timing_cfg_3 to match docsKumar Gala2008-04-29-2/+2
| | | | | | | All the 85xx and 86xx UM describe the register as timing_cfg_3 not as ext_refrec. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Remove erroneous or extra spd.h #includers.Jon Loeliger2008-03-05-5/+1
| | | | | | | | | | Many of the spd.h #includers don't need it, and wanted to have spd_sdram() declared instead. Since they didn't get that, some also had open coded extern declarations of it instead or as well. Fix it all up by using spd_sdram.h where needed. Signed-off-by: Jon Loeliger <jdl@freescale.com>
* 86xx: Fix renamed GUR symbols in sbc8641d board.Jon Loeliger2008-02-25-2/+4
| | | | | | | | | Back in commit a551cee99ad1d1da20fd23ad265de47448852f56 (86xx: Fix GUR PCI config registers properly), we should have changed the MPC86xx_PORBMSR_HA and MPC86xx_PORDEVSR_IO_SEL symbols in the sbc8641d board as well. Fix this oversight. Signed-off-by: Jon Loeliger <jdl@freescale.com>
* 86xx: Convert sbc8641d to use libfdt.Jon Loeliger2008-02-18-14/+27
| | | | | | | | | | | | | | | This is the proper fix for a missing closing brace in the function ft_cpu_setup() noticed by joe.hamman <at> embeddedspecialties.com. The ft_cpu_setup() function in mpc8641hpcn.c should have been removed earlier as it was under the obsolete CONFIG_OF_FLAT_TREE, but was missed. Only, the sbc8641d was nominally still using it. It all got ripped out, and the funcality that was in ft_board_setup() was refactored to remove the CPU portions into the new file cpu/mpc86xx/fdt.c instead. Make sbc8641d use this now. Based loosely on an original patch from joe.hamman@embeddedspecialties.com Signed-off-by: Jon Loeliger <jdl@freescale.com>
* Modify SBC8641D to use new Freescale PCI routinesJoe Hamman2007-08-13-38/+118
| | | | | | | | PCI-Express sockets 1 and 2 verified working with Intel Pro/1000 PT adapter. Signed-off-by: Joe Hamman <joe.hamman@embeddedspecialties.com> Signde-off-by: Jon Loeliger <jdl@freescale.com>
* Add support for SBC8641D. Board files.Joe Hamman2007-08-10-0/+326
Add support for Wind River's SBC8641D reference board. Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com> Acked-by: Wolfgang Denk <wd@denx.de> Acked-by: Jon Loeliger <jdl@freescale.com>
generated by cgit v1.1 at 2024-12-01 04:22:17 +0000