summaryrefslogtreecommitdiff
path: root/board/samsung
Commit message (Collapse)AuthorAgeLines
* Rename TEXT_BASE into CONFIG_SYS_TEXT_BASEWolfgang Denk2010-10-18-11/+11
| | | | | | | | | | | | The change is currently needed to be able to remove the board configuration scripting from the top level Makefile and replace it by a simple, table driven script. Moving this configuration setting into the "CONFIG_*" name space is also desirable because it is needed if we ever should move forward to a Kconfig driven configuration system. Signed-off-by: Wolfgang Denk <wd@denx.de>
* ARMV7: S5P: rename the member of gpio structureMinkyu Kang2010-08-30-5/+5
| | | | | | | | | Typically we declare the name of gpio structure to "gpio", so it was duplicated around the name. (e.g: gpio->gpio_a) This patch modified the naming that is removing "gpio_". Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* S5P: Use accessor functions instead of SoC specific defines to access the ↵Minkyu Kang2010-08-17-6/+7
| | | | | | | | | | | base address This patch is intended to prepare the other S5P SoC. (s5pc210) If use SoC specific defines then can't share with other SoC. So, make the accessor functions for access the base address by common way. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* s5p_goni: enable mmc0Minkyu Kang2010-08-03-0/+37
| | | | | | | | Adds the board_mmc_init function and enable the mmc command Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* SAMSUNG: goni: add the GPL licenceMinkyu Kang2010-06-09-1/+19
| | | | | | Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Tom <Tom@bumblecow.com>
* s5pc1xx: Add support for Samsung Goni boardMinkyu Kang2010-06-03-0/+1011
| | | | | | | This patch adds support for the Samsung Goni board (S5PC110 SoC) Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* arm: Move cpu/$CPU to arch/arm/cpu/$CPUPeter Tyser2010-04-13-2/+2
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* SAMSUNG: SMDKC100: Adds ethernet support.Naveen Krishna CH2010-04-03-0/+39
| | | | | | | | | | | Add setup for ethernet on SMDKC100, allowing kernel/ramdisk to be loaded over tftp. The preinit function will configure GPIO (GPK0CON) & SROMC to look for environment in SROM Bank 3. Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Add a unified s3c24x0 header filekevin.morfitt@fearnside-systems.co.uk2009-11-27-2/+2
| | | | | | | | | | This patch adds a unified s3c24x0 cpu header file that selects the header file for the specific s3c24x0 cpu from the SOC and CPU configs defined in board config file. This removes the current chain of s3c24-type #ifdef's from the s3c24x0 code. Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* s3c64xx: move s3c64xx header files to asm-arm/arch-s3c64xxMinkyu Kang2009-11-27-2/+2
| | | | | | | This patch moves the s3c64xx header files from include/ to include/asm-arm/arch-s3c64xx Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Move s3c24x0 header files to asm-arm/arch-s3c24x0/kevin.morfitt@fearnside-systems.co.uk2009-11-27-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch moves the s3c24x0 header files from include/ to include/asm-arm/arch-s3c24x0/. checkpatch.pl showed 2 errors and 3 warnings. The 2 errors were both due to a non-UTF8 character in David M?ller's name: ERROR: Invalid UTF-8, patch and commit message should be encoded in UTF-8 #489: FILE: include/asm-arm/arch-s3c24x0/s3c2410.h:3: + * David M?ller ELSOFT AG Switzerland. d.mueller@elsoft.ch As David's name correctly contains a non-UTF8 character I haven't fixed these errors. The 3 warnings were all because of the use of 'volatile' in s3c24x0.h: WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt #673: FILE: include/asm-arm/arch-s3c24x0/s3c24x0.h:35: +typedef volatile u8 S3C24X0_REG8; +typedef volatile u16 S3C24X0_REG16; +typedef volatile u32 S3C24X0_REG32; I'll fix these errors in another patch. Tested by running MAKEALL for ARM8 targets and ensuring there were no new errors or warnings. Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Clean-up of s3c24x0 drivers excluding nand driverkevin.morfitt@fearnside-systems.co.uk2009-10-13-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch re-formats the arm920t s3c24x0 driver files, excluding the nand driver, in preparation for changes to add support for the Embest SBC2440-II Board. The changes are as follows: - re-indent the code using Lindent - make sure register layouts are defined using a C struct - replace the upper-case typedef'ed C struct names with lower case non-typedef'ed ones - make sure registers are accessed using the proper accessor functions - run checkpatch.pl and fix any error reports It assumes the following patch has been applied first: - [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009 - patches 1/4 and 2/4 of this series Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have any s3c2400 or s3c2410 boards but need this patch applying before I can submit patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400, smdk2410 and trab configs to use the mtd nand driver (which isn't used by any board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or errors were found. Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* s5pc1xx: add support SMDKC100 boardMinkyu Kang2009-10-13-0/+617
| | | | | | | Adds new board SMDKC100 that uses s5pc100 SoC Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
* Convert CS8900 Ethernet driver to CONFIG_NET_MULTI APIBen Warren2009-08-25-0/+36
| | | | | | | | | | | | | | | All in-tree boards that use this controller have CONFIG_NET_MULTI added Also: - changed CONFIG_DRIVER_CS8900 to CONFIG_CS8900 - changed CS8900_BASE to CONFIG_CS8900_BASE - changed CS8900_BUS?? to CONFIG_CS8900_BUS?? - cleaned up line lengths - modified VCMA9 command function that accesses the device - removed MAC address initialization from lib_arm/board.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Tested-by: Wolfgang Denk <wd@denx.de> Acked-by: Wolfgang Denk <wd@denx.de>
* Remove legacy NAND and disk on chip references from boards.Scott Wood2009-07-17-11/+0
| | | | Signed-off-by: Scott Wood <scottwood@freescale.com>
* arm: unify linker scriptJean-Christophe PLAGNIOL-VILLARD2009-06-12-114/+2
| | | | | | | | | | | | all arm boards except a few use the same cpu linker script so move it to cpu/$(CPU) that could be overwrite in following order SOC BOARD via the corresponding config.mk Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Redundant Environment: protect full sector sizeWolfgang Denk2009-06-04-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Several boards used different ways to specify the size of the protected area when enabling flash write protection for the sectors holding the environment variables: some used CONFIG_ENV_SIZE and CONFIG_ENV_SIZE_REDUND, some used CONFIG_ENV_SECT_SIZE, and some even a mix of both for the "normal" and the "redundant" areas. Normally, this makes no difference at all. However, things are different when you have to deal with boards that can come with different types of flash chips, which may have different sector sizes. Here we may have to chose CONFIG_ENV_SECT_SIZE such that it fits the biggest sector size, which may include several sectors on boards using the smaller sector flash types. In such a case, using CONFIG_ENV_SIZE or CONFIG_ENV_SIZE_REDUND to enable the protection may lead to the case that only the first of these sectors get protected, while the following ones aren't. This is no real problem, but it can be confusing for the user - especially on boards that use CONFIG_ENV_SECT_SIZE to protect the "normal" areas, while using CONFIG_ENV_SIZE_REDUND for the "redundant" area. To avoid such inconsistencies, I changed all sucn boards that I found to consistently use CONFIG_ENV_SECT_SIZE for protection. This should not cause any functional changes to the code. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Paul Ruhland Cc: Pantelis Antoniou <panto@intracom.gr> Cc: Stefan Roese <sr@denx.de> Cc: Gary Jennejohn <garyj@denx.de> Cc: Dave Ellis <DGE@sixnetio.com> Acked-by: Stefan Roese <sr@denx.de>
* Fix e-mail address of Gary Jennejohn.Detlev Zundel2009-05-15-9/+9
| | | | Signed-off-by: Detlev Zundel <dzu@denx.de>
* Move machine specific code to board at s3c64xx (v2)Kyungmin Park2009-04-05-0/+7
| | | | | | | | | | Move machine specific code to smdk6400. Some board use OneNAND instead of NAND. Some register MP0_CS_CFG[5:0] are controled by both h/w and s/w. So it's better to use macro instead of hard-coded value. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* Fix all linker script to handle all rodata sectionsTrent Piepho2009-03-20-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A recent gcc added a new unaligned rodata section called '.rodata.str1.1', which needs to be added the the linker script. Instead of just adding this one section, we use a wildcard ".rodata*" to get all rodata linker section gcc has now and might add in the future. However, '*(.rodata*)' by itself will result in sub-optimal section ordering. The sections will be sorted by object file, which causes extra padding between the unaligned rodata.str.1.1 of one object file and the aligned rodata of the next object file. This is easy to fix by using the SORT_BY_ALIGNMENT command. This patch has not be tested one most of the boards modified. Some boards have a linker script that looks something like this: *(.text) . = ALIGN(16); *(.rodata) *(.rodata.str1.4) *(.eh_frame) I change this to: *(.text) . = ALIGN(16); *(.eh_frame) *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) This means the start of rodata will no longer be 16 bytes aligned. However, the boundary between text and rodata/eh_frame is still aligned to 16 bytes, which is what I think the real purpose of the ALIGN call is. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
* move Samsung's board to board/samsungJean-Christophe PLAGNIOL-VILLARD2009-01-29-0/+1754
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Align end of bss by 4 bytesSelvamuthukumar2008-11-18-1/+1
| | | | | | | | | | Most of the bss initialization loop increments 4 bytes at a time. And the loop end is checked for an 'equal' condition. Make the bss end address aligned by 4, so that the loop will end as expected. Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
* rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD2008-10-18-3/+3
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Coding style cleanup, update CHANGELOGWolfgang Denk2008-09-13-16/+16
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* smdk6400: add gitignoreJean-Christophe PLAGNIOL-VILLARD2008-08-31-0/+5
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM: Add support for S3C6400 based SMDK6400 boardGuennadi Liakhovetski2008-08-31-0/+592
SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl driver for it too. The board can also boot from the NOR flash, but due to hardware limitations it can only address 64KiB on it, which is not enough for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6. Signed-off-by: Guennadi Liakhovetski <lg@denx.de>