arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	ARMV7: OMAP: Overo: Autodetect presence/absence of transceiver on mmc2	Steve Sakoman	2010-09-08	-2/+80
\| \| \| \| \| \| \| \| \| \|	An upcoming version of Overo uses a Wifi/BT module with 1.8V signaling, eliminating the need for an external transceiver to handle the level shifting. This patch detects whether an external transceiver is present and adjusts the pinmux settings as appropriate. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	ARMV7: OMAP: Configure Overo's second network chip	Steve Sakoman	2010-09-08	-9/+19
\| \| \| \| \| \| \| \| \|	Confiures GPMC timings for both chips and also configures pinmux for GPIO_65, which is used as the interrupt signal for the second chip Signed-off-by: Scott Ellis <scott@jumpnowtek.com> Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	ARMV7: OMAP: Add board revision detection for Overo	Steve Sakoman	2010-09-08	-3/+35
\| \| \| \| \| \| \| \| \| \| \|	The latest Overo COM modules encode their revision number on GPIOs 115, 113, and 112. All boards to date have no pullups on these pins and hence appear as revision 0. This patch reads and prints the revision information. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	ARMV7: OMAP: Enable input driver on Overo's MMC1_CLK and MMC3_CLK pinmux setup	Steve Sakoman	2010-09-08	-2/+2
\| \| \| \| \| \| \| \|	This patch modifies the pinmux setup for MMC1_CLK and MMC3_CLK to enable the input driver. MMC2_CLK was already properly configured. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	Overo GPMC registers	Scott Ellis	2010-02-12	-7/+16
\| \| \| \| \| \| \| \| \|	Use appropriate GPMC timings for the LAN9221 controller on the Gumstix Overo expansion boards not the values in arch-omap3/mem.h which are for a different ethernet controller. Signed-off-by: Scott Ellis <scott@jumpnowtek.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	TWL4030: make LEDs selectable for twl4030_led_init()	Grazvydas Ignotas	2010-01-04	-1/+1
\| \| \| \| \| \| \| \| \| \| \| \|	Not all boards have both LEDs hooked, so enabling both on boards with single LED will just waste power. Make it possible to choose LEDs by adding argument to twl4030_led_init(). Using this turn on only LEDB for pandora, leave both LEDs on for all other boards, as it was before this patch. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
*	TI: OMAP3: Overo Tobi ethernet support	Olof Johansson	2009-10-13	-31/+91
\| \| \| \| \| \| \| \| \| \| \| \| \|	Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded over tftp. This also refactors the smc911x driver to allow for detecting when the chip is missing. I.e. the detect_chip() function is called earlier and will abort gracefully when the Chip ID read returns all 1's. Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by: Dirk Behme <dirk.behme@googlemail.com> Acked-by: Ben Warren <biggerbadderben@gmail.com>
*	OMAP3: Clean up whitespace in mux configs	Olof Johansson	2009-10-13	-322/+322
\| \| \| \| \| \| \| \| \| \| \|	Switch from space-based indentation to tab-based in mux configs, as pointed out by WD at: http://lists.denx.de/pipermail/u-boot/2009-September/061241.html Nothing but whitespace changes in this patch (diff -w gives no output). Signed-off-by: Olof Johansson <olof@lixom.net>
*	omap3: move the other boards to board/	Jean-Christophe PLAGNIOL-VILLARD	2009-09-05	-0/+537
	Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>