| Commit message (Collapse) | Author | Age | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There are currently 3 versions of the zoom2 board.
The production board, that is currently being released.
The beta board, similar in form to the production board but not released.
The alpha board, a set of PCBs with a very limited circulation.
GPIO 94 is used to determine the version of the board. If GPIO 94 is clear,
the board is a production board, otherwise it is a beta board.
The alpha board will likely be mistaken for a beta board. An alpha board
was unavailible for testing.
This has been tested on the beta and production boards.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
|
|
|
|
| |
This patch controls the large LED on the top left of the zoom2.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board.
The default serial is from the USB connector on left side of the debug board.
The USB connector will produce 2 of the 4 UARTS. On your host pick the first
enumeration.
The details of the setting of the serial gpmc setup are not available.
The values were provided by another party.
The serial port set up is the same with Zoom1.
Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow.
The kernel bootargs are
console=ttyS3,115200n8
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The logicpd web site is a good source for general information on this board.
Please start looking here if the below links are broken.
http://www.logicpd.com
This is a pdf of the product
http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
This is a pdf of the product quick start guide.
The debug board is described here.
http://support.logicpd.com/downloads/1165/
This is a wiki showing the debug board in use
https://omapzoom.org/gf/project/omapzoom/wiki/?pagename=GettingStartedWithZoomII_AKA_OMAP34XII_MDP
The zoom2 has an auxillary board that contains the serial, net, jtag and
battery simulator. This change supports a runtime check if the debug board is
connected.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
Zoom2 is a new board from Texas Instruments and LogicPD
The logicpd web site is a good source for general information on this board.
Please start looking here if the below links are broken.
http://www.logicpd.com
This is a pdf of the product
http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
This is the product description web page
http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp
This patch provides a zoom2 base target by copying zoom1 and by making some
obvious changes.
To configure, run
make omap3_zoom2_config
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|