summaryrefslogtreecommitdiff
path: root/board/olimex
Commit message (Collapse)AuthorAgeLines
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-51/+3
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* mx23_olinuxino: Do not set voltage selection bit for SSP padsFabio Estevam2013-05-06-1/+1
| | | | | | mx23 SSP pad registers do not contain voltage selection bit, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx23_olinuxino: Fix DDR pin iomux settingsFabio Estevam2013-05-05-1/+1
| | | | | | | Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from Freescale, which results in much better stability. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx23_olinuxino: Fix warning for implicit declarationOtavio Salvador2013-03-07-0/+1
| | | | | | | | | | | | | | Fixes a build warning of implicit declaration of gpio_direction_output, as bellow: ,---- | mx23_olinuxino.c: In function 'board_early_init_f': | mx23_olinuxino.c:51:2: warning: implicit declaration | of function 'gpio_direction_output' | [-Wimplicit-function-declaration] `---- Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* mx23_olinuxino: Enable USB supportOtavio Salvador2013-03-07-0/+9
| | | | | | This enabled USB support for the mx23_olinuxino board. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* mx23_olinuxino: Add support for status LEDOtavio Salvador2013-03-07-0/+11
| | | | | | | This allow user to know if the bootloader is running, even without a serial console. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* mxs: mmc: mx23_olinuxino: Add MMC supportMarek Vasut2013-01-28-1/+30
| | | | | | | | | Add support for the MMC attached to SSP1. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* mxs: Boost the memory power supplyMarek Vasut2013-01-28-1/+1
| | | | | | | | | | | The memory power supply on MX23 didn't pump out enough juice into the DRAM chip, thus caused occasional memory corruption. Fix this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
* mxs: Add MX23 olinuxino board supportMarek Vasut2013-01-21-0/+188
This patch adds support for MX23-based Olinuxino board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>