arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	board: arm: convert makefiles to Kbuild style	Masahiro Yamada	2013-11-01	-21/+2
\| \| \| \| \| \| \| \| \| \| \| \|	Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Tom Rini <trini@ti.com>
*	ARM: mxs: Receive r0 and r1 passed from BootROM	Marek Vasut	2013-09-10	-2/+2
\| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \|	Make sure value in register r0 and r1 is preserved and passed to the board_init_ll() and mxs_common_spl_init() where it can be processed further. The value in r0 can be configured during the BootStream generation to arbitary value, r1 contains pointer to return value from CALL'd function. This patch also clears the value in r0 before returning to BootROM to make sure the BootROM is not confused by this value. Finally, this patch cleans up some comments in the start.S file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
*	Add GPL-2.0+ SPDX-License-Identifier to source files	Wolfgang Denk	2013-07-24	-51/+3
\| \| \| \| \| \|	Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
*	mx23_olinuxino: Do not set voltage selection bit for SSP pads	Fabio Estevam	2013-05-06	-1/+1
\| \| \| \| \| \|	mx23 SSP pad registers do not contain voltage selection bit, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
*	mx23_olinuxino: Fix DDR pin iomux settings	Fabio Estevam	2013-05-05	-1/+1
\| \| \| \| \| \| \|	Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from Freescale, which results in much better stability. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
*	mx23_olinuxino: Fix warning for implicit declaration	Otavio Salvador	2013-03-07	-0/+1
\| \| \| \| \| \| \| \| \| \| \| \| \| \|	Fixes a build warning of implicit declaration of gpio_direction_output, as bellow: ,---- \| mx23_olinuxino.c: In function 'board_early_init_f': \| mx23_olinuxino.c:51:2: warning: implicit declaration \| of function 'gpio_direction_output' \| [-Wimplicit-function-declaration] `---- Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
*	mx23_olinuxino: Enable USB support	Otavio Salvador	2013-03-07	-0/+9
\| \| \| \| \| \|	This enabled USB support for the mx23_olinuxino board. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
*	mx23_olinuxino: Add support for status LED	Otavio Salvador	2013-03-07	-0/+11
\| \| \| \| \| \| \|	This allow user to know if the bootloader is running, even without a serial console. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
*	mxs: mmc: mx23_olinuxino: Add MMC support	Marek Vasut	2013-01-28	-1/+30
\| \| \| \| \| \| \| \| \|	Add support for the MMC attached to SSP1. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
*	mxs: Boost the memory power supply	Marek Vasut	2013-01-28	-1/+1
\| \| \| \| \| \| \| \| \| \| \|	The memory power supply on MX23 didn't pump out enough juice into the DRAM chip, thus caused occasional memory corruption. Fix this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
*	mxs: Add MX23 olinuxino board support	Marek Vasut	2013-01-21	-0/+188
	This patch adds support for MX23-based Olinuxino board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>