arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	Add GPL-2.0+ SPDX-License-Identifier to source files	Wolfgang Denk	2013-07-24	-51/+3
\| \| \| \| \| \|	Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
*	mx23_olinuxino: Do not set voltage selection bit for SSP pads	Fabio Estevam	2013-05-06	-1/+1
\| \| \| \| \| \|	mx23 SSP pad registers do not contain voltage selection bit, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
*	mx23_olinuxino: Fix DDR pin iomux settings	Fabio Estevam	2013-05-05	-1/+1
\| \| \| \| \| \| \|	Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from Freescale, which results in much better stability. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
*	mx23_olinuxino: Fix warning for implicit declaration	Otavio Salvador	2013-03-07	-0/+1
\| \| \| \| \| \| \| \| \| \| \| \| \| \|	Fixes a build warning of implicit declaration of gpio_direction_output, as bellow: ,---- \| mx23_olinuxino.c: In function 'board_early_init_f': \| mx23_olinuxino.c:51:2: warning: implicit declaration \| of function 'gpio_direction_output' \| [-Wimplicit-function-declaration] `---- Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
*	mx23_olinuxino: Enable USB support	Otavio Salvador	2013-03-07	-0/+9
\| \| \| \| \| \|	This enabled USB support for the mx23_olinuxino board. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
*	mx23_olinuxino: Add support for status LED	Otavio Salvador	2013-03-07	-0/+11
\| \| \| \| \| \| \|	This allow user to know if the bootloader is running, even without a serial console. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
*	mxs: mmc: mx23_olinuxino: Add MMC support	Marek Vasut	2013-01-28	-1/+30
\| \| \| \| \| \| \| \| \|	Add support for the MMC attached to SSP1. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
*	mxs: Boost the memory power supply	Marek Vasut	2013-01-28	-1/+1
\| \| \| \| \| \| \| \| \| \| \|	The memory power supply on MX23 didn't pump out enough juice into the DRAM chip, thus caused occasional memory corruption. Fix this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
*	mxs: Add MX23 olinuxino board support	Marek Vasut	2013-01-21	-0/+188
	This patch adds support for MX23-based Olinuxino board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>