summaryrefslogtreecommitdiff
path: root/board/nvidia
Commit message (Collapse)AuthorAgeLines
* ARM: tegra: make all I2C ports open-drainStephen Warren2014-03-26-16/+16
| | | | | | | | | | | I2C protocol requires open-drain IOs. Fix the Dalmore and Venice2 pinmux tables to configure the IOs correctly. Without this, Tegra may actively drive the lines high while an external device is actively driving the lines low, which can only lead to bad things. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* venice2: move device tree to fix build errorMasahiro Yamada2014-02-20-84/+0
| | | | | | | | | | | | | | | Commit 5ab502cb gathered all device tree sources to arch/$(ARCH)/dts/. So tegra124-venice2.dts also must go to arch/arm/dts directory to build venice2 board. (Commit 5ab502cb had been posted before venice2 board support was merged. So an unvisible conflict happened.) Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@ti.com>
* dts: move device tree sources to arch/$(ARCH)/dts/Masahiro Yamada2014-02-19-680/+0
| | | | | | | | | | | | | | | | | Unlike Linux Kernel, U-Boot historically had *.dts files under board/$(VENDOR)/dts/ and *.dtsi files under arch/$(ARCH)/dts/. I think arch/$(ARCH)/dts dicretory is a better location to store both *.dts and *.dtsi files. For example, before this commit, board/xilinx/dts directory had both Microblaze dts (microblaze-generic.dts) and ARM dts (zynq-*.dts), which are totally unrelated. This commit moves *.dts to arch/$(ARCH)/dts/ directories, allowing us to describe nicely mutiple DTBs generation in the next commit. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* kbuild: change out-of-tree buildMasahiro Yamada2014-02-19-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit changes the working directory where the build process occurs. Before this commit, build process occurred under the source tree for both in-tree and out-of-tree build. That's why we needed to add $(obj) prefix to all generated files in makefiles like follows: $(obj)u-boot.bin: $(obj)u-boot Here, $(obj) is empty for in-tree build, whereas it points to the output directory for out-of-tree build. And our old build system changes the current working directory with "make -C <sub-dir>" syntax when descending into the sub-directories. On the other hand, Kbuild uses a different idea to handle out-of-tree build and directory descending. The build process of Kbuild always occurs under the output tree. When "O=dir/to/store/output/files" is given, the build system changes the current working directory to that directory and restarts the make. Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>" syntax for descending into sub-directories. (We can write it like "make $(obj)=<sub-dir>" with a shorthand.) This means the current working directory is always the top of the output directory. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Gerhard Sittig <gsi@denx.de>
* ARM: tegra: add Venice2 (Tegra124) boardTom Warren2014-02-03-0/+510
| | | | | | | | | | | | | These are the board files for Venice2 (Tegra124), plus the AS3722 PMIC files. PMIC init will be moved to pmic_common_init later. This builds/boots on Venice2, SPI/MMC/USB/I2C all work. Audio, display and WB/LP0 are not supported yet. Signed-off-by: Tom Warren <twarren@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: add DT files for Tegra124 and Venice2Tom Warren2014-02-03-0/+84
| | | | | | | | | | These are fairly complete, and near-clones of Tegra114 Venice, with an additional I2C port, and MMC address changes for Tegra124. Signed-off-by: Tom Warren <twarren@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: only build __pinmux_nand() when it's neededTom Warren2014-02-03-0/+2
| | | | | | | | | | | | | | | __pinmux_nand() won't compile if PERIPH_ID_NDFLASH isn't defined. Prevent this from causing build problems on newer SoCs without NAND support (or without SW support for NAND yet), but preventing compilation unless the function will actually be used, i.e. when CONFIG_TEGRA_NAND is defined. Signed-off-by: Tom Warren <twarren@nvidia.com> [swarren, rewrote commit description, moved ifdef around whole function rather than just body] Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* lib: time: add weak timer_init() functionDarwin Rambo2014-01-24-11/+0
| | | | | | | | | | If timer_init() is made a weak stub function, then it allows us to remove several empty timer_init functions for those boards that already have a timer initialized when u-boot starts. Architectures that use the timer framework may also remove the need for timer.c. Signed-off-by: Darwin Rambo <drambo@broadcom.com> Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
* Makefile: make directories by Makefile.buildMasahiro Yamada2013-11-17-4/+0
| | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* Makefile: convert makefiles to Kbuild style and delete grep switchMasahiro Yamada2013-11-01-28/+2
| | | | | | | | | | | | | We have converted all makefiles needed to build $(LIBS). Until this commit we used to grep switch so that U-Boot style and Kbuild style makefiles coexist. But we do not need any more. Goint forward, use always Kbuild style Makefile when adding a new Makefile Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* board: arm: convert makefiles to Kbuild styleMasahiro Yamada2013-11-01-140/+7
| | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Tom Rini <trini@ti.com>
* usb: new board-specific USB init interfaceMateusz Zalega2013-10-20-1/+3
| | | | | | | | | | | | | | This commit unifies board-specific USB initialization implementations under one symbol (usb_board_init), declaration of which is available in usb.h. New API allows selective initialization of USB controllers whenever needed. Signed-off-by: Mateusz Zalega <m.zalega@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com>
* Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini2013-07-24-2/+2
|\ | | | | | | | | | | | | | | | | | | | | The sandburst-specific i2c drivers have been deleted, conflict was just over the SPDX conversion. Conflicts: board/sandburst/common/ppc440gx_i2c.c board/sandburst/common/ppc440gx_i2c.h Signed-off-by: Tom Rini <trini@ti.com>
| * tegra: i2c: Enable new CONFIG_SYS_I2C frameworkSimon Glass2013-07-23-2/+2
| | | | | | | | | | | | | | | | This enables CONFIG_SYS_I2C on Tegra, updating existing boards and the Tegra i2c driver to support this. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Heiko Schocher <hs@denx.de>
* | Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-226/+13
|/ | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* ARM: tegra: enable LCD panel on VentanaStephen Warren2013-07-11-0/+32
| | | | | Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: enable LCD panel on HarmonyStephen Warren2013-07-11-0/+39
| | | | | Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: Tegra: USB: EHCI: Add support for Tegra30/Tegra114Jim Lin2013-07-11-0/+1
| | | | | | | | | | Tegra30 and Tegra114 are compatible except PLL parameters. Tested on Tegra30 Cardhu, and Tegra114 Dalmore platforms. All works well. Signed-off-by: Jim Lin <jilin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: Tegra: FDT: Add USB EHCI function for T30/T114Jim Lin2013-07-11-0/+19
| | | | | | | | | | Add DT node for USB EHCI function. Add support for T30-Cardhu, T30-Beaver, T114-Dalmore boards. Signed-off-by: Jim Lin <jilin@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* Tegra: T30: Beaver: Fix board/board_name env vars, s/b beaver, not cardhuTom Warren2013-05-28-0/+38
| | | | | | | | | | Did a 'strings u-boot-dtb-tegra.bin | less' and saw that both board and board_name == beaver. Didn't test as I have no T30 Beaver board here. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com>
* Tegra: T30: Beaver board support.Tom Warren2013-04-15-0/+71
| | | | | | | | Beaver is a Tegra30 board that is nearly 100% compatible w/Cardhu. Add a Beaver build so it can begin to be differentiated, if need be. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra: Split tegra_get_chip_type() into soc & sku funcsTom Warren2013-04-15-1/+1
| | | | | | | | | | | As suggested by Stephen Warren, use tegra_get_chip() to return the pure CHIPID for a Tegra SoC (i.e. 0x20 for Tegra20, 0x30 for Tegra30, etc.) and rename tegra_get_chip_type() to reflect its true function, i.e. tegra_get_chip_sku(), which returns an ID like TEGRA_SOC_T25, TEGRA_SOC_T33, etc. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra114: MMC: Add SD bus power-rail init routineTom Warren2013-03-25-0/+62
| | | | | | | T114 requires SD bus power-rail bringup for the SDIO card on SDMMC3. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra114: Dalmore: Add SDIO3 pad config to pinctrl_config tableTom Warren2013-03-25-0/+10
| | | | | | | | SDIO1 (the SD-card slot on Dalmore) needs to have its pads setup before the MMC driver is added. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra114: fdt: Add SDMMC (sdhci) nodes for T114 boards (Dalmore for now)Tom Warren2013-03-25-0/+13
| | | | | | | Took these values directly from the kernel dts files. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* tegra114: dalmore: fdt: enable dalmore SPI controllerAllen Martin2013-03-25-0/+5
| | | | | | | | | Dalmore has a SPI flash part attached to controller 4, so enable controller 4 and set to 25MHz. Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* spi: add common fdt SPI driver interfaceAllen Martin2013-03-25-1/+1
| | | | | | | | | | | Add a common interface to fdt based SPI drivers. Each driver is represented by a table entry in fdt_spi_drivers[]. If there are multiple SPI drivers in the table, the first driver to return success from spi_init() will be registered as the SPI driver. Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* tegra: spi: rename tegra SPI driversAllen Martin2013-03-25-1/+1
| | | | | | | | | Rename tegra SPI drivers to tegra20_flash and tegra20_slink in preparation for commonization and addition of tegra114_spi. Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* tegra: remove support for UART SPI switchAllen Martin2013-03-25-130/+1
| | | | | | | | | | This feature was only used for tegra20 seaboard that had a pinmux conflict on the SPI pins. These boards were never manufactured, so remove this support to clean up SPI driver. Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra114: Dalmore: Add pad config tables/code based on pinmux codeTom Warren2013-03-14-0/+12
| | | | | | | | | | | | | | | Pad config registers exist in APB_MISC_GP space, and control slew rate, drive strengh, schmidt, high-speed, and low-power modes for all of the pingroups in Tegra30. This builds off of the pinmux way of constructing init tables to configure select pads (SDIOCFG, for instance) during pinmux_init(). Currently, no padcfg entries exist. SDIO3CFG will be added when the MMC driver is added as per the TRM to work with the SD-card slot on Dalmore E1611. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra114: fdt: Move aliases from dtsi to dts file as per other TegrasTom Warren2013-03-14-0/+8
| | | | | | | All other Tegra boards have their alias nodes in the .dts file Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra114: Dalmore: Always use DEFAULT instead of DISABLE for lock bitsTom Warren2013-03-14-12/+12
| | | | | | | | | | | | | | The pinmux code issues a warning if the caller attempts to disable the lock bit in a pinmux register, since this is impossible (once it's locked, the only way to unlock it is to reset the device/pmt controller). The I2C/DDC/CEC/USB macros expect a lock setting to be passed in, and the previous setting of DISABLE caused the pinmux table parsing code to issue the warning. Changing the lock bits in these table entries to DEFAULT (i.e. don't touch it) fixes this. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra30: MMC: Add SD bus power-rail and SDMMC pad init routinesTom Warren2013-03-14-1/+81
| | | | | | | T30 requires specific SDMMC pad programming, and bus power-rail bringup. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra30: fdt: Add SDMMC (sdhci) nodes for T30 boards (Cardhu for now)Tom Warren2013-03-14-0/+15
| | | | | | | Took these values directly from the kernel dts files. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra30: Cardhu: Add pad config tables/code based on pinmux codeTom Warren2013-03-14-3/+24
| | | | | | | | | | | | | | | | Pad config registers exist in APB_MISC_GP space, and control slew rate, drive strengh, schmidt, high-speed, and low-power modes for all of the pingroups in Tegra30. This builds off of the pinmux way of constructing init tables to configure select pads (SDIOCFG, for instance) during pinmux_init(). Currently, only SDIO1CFG is changed as per the TRM to work with the SD-card slot on Cardhu. Thanks to StephenW for the suggestion/original idea. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra114: pinmux: Update pinmux tables & code, fix a bug w/SDMMC3 initTom Warren2013-03-14-180/+286
| | | | | | | | | | | | | Use the latest tables & code from our internal U-Boot repo. The SDMMC3_CD, CLK_LB_IN and CLK_LB_OUT offsets in the pingroup table were off by a few indices, causing the pinmux init code to write bad data to the PINMUX_AUX_ regs. This also enabled the lock bit, which made it impossible to reconfig the pads correctly for SDMMC3 (SD card on Dalmore) operation. Also fixes SPI_CS2_N, USB_VBUS_EN0, HDMI_CEC and UART2_RXD/TXD muxes. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra30: Cardhu: Remove unneeded cardhu.c.mmc fileTom Warren2013-03-14-151/+0
| | | | | | | | This was an older debug/developmental file that got added accidentally. Not needed/used in any Cardhu build. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra30: fdt: Sync DT nodes with kernel DT files (I2C, SPI, GPIO, clock)Tom Warren2013-03-14-0/+5
| | | | | | | Minor edits to clock, apbdma and SPI, make I2C match kernel DT, and add gpio Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra: fdt: Remove memreserve line from Cardhu/Seaboard DT filesTom Warren2013-03-14-2/+0
| | | | | | | Not used, and wrong in Cardhu's case Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra: MMC: Add DT support to MMC driver for all T20 boardsTom Warren2013-03-14-74/+32
| | | | | | | | | | | | tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc. Tested on Seaboard, fully functional. Tamonten boards (medcom-wide, plutux, and tec) use a different/new dtsi file w/common settings. Signed-off-by: Tom Warren <twarren@nvidia.com> Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra: fdt: Add/enhance sdhci (mmc) nodes for all T20 DT filesTom Warren2013-03-14-6/+56
| | | | | | | | | | Linux dts files were used for those boards that didn't already have sdhci info populated. Tamonten has their own dtsi file with common sdhci nodes (sourced from Linux). Signed-off-by: Tom Warren <twarren@nvidia.com> Tested-by: Thierry Reding <thierry.reding@avionic-design.de> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra: fdt: Change /include/ to #include for C preprocessorTom Warren2013-03-14-6/+6
| | | | | | | | | dts Makefile has the arch & board include paths added to DTS_CPPFLAGS. This allows the use of '#include "xyz"' in the dts/dtsi file which helps the C preprocessor find common dtsi include files. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra114: fdt: Update DT files with I2C info for T114/DalmoreTom Warren2013-03-14-0/+25
| | | | | | | | | | | T114, like T30, does not have a separate/different DVC (power I2C) controller like T20 - all 5 I2C controllers are identical, but I2C5 is used to designate the controller intended for power control (PWR_I2C in the schematics). PWR_I2C is set to 400KHz. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* tegra: usb: move implementation into right directoryLucas Stach2013-03-14-1/+1
| | | | | | | | | | | | | | | | This moves the Tegra USB implementation into the drivers/usb/host directory. Note that this merges the old /arch/arm/cpu/armv7/tegra20/usb.c file into ehci-tegra.c. No code changes, just moving stuff around. v2: While at it also move some defines and the usb.h header file to make usb driver usable for Tegra30. NOTE: A lot more work is required to properly init the PHYs and PLL_U on Tegra30, this is just to make porting easier and it does no harm here. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* Tegra114: Add/enable Dalmore build (T114 reference board)Tom Warren2013-02-11-0/+317
| | | | | | | This build is stripped down. It boots to the command prompt. GPIO is the only peripheral supported. Others TBD. Signed-off-by: Tom Warren <twarren@nvidia.com>
* Tegra114: Add generic Tegra114 build supportTom Warren2013-02-11-1/+1
| | | | | | | This patch adds basic Tegra114 (T114) build support - no specific board is targeted. Signed-off-by: Tom Warren <twarren@nvidia.com>
* Tegra114: Dalmore: Add DT filesTom Warren2013-02-11-0/+13
| | | | | | | | These are stripped down for bringup, They'll be filled out later to match-up with the kernel DT contents, and/or as devices are brought up (mmc, usb, spi, etc.). Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: add SPI SLINK driverAllen Martin2013-02-11-1/+2
| | | | | | | | | | | | | | | | | | | | | | Add driver for tegra SPI "SLINK" style driver. This controller is similar to the tegra20 SPI "SFLASH" controller. The difference is that the SLINK controller is a genernal purpose SPI controller and the SFLASH controller is special purpose and can only talk to FLASH devices. In addition there are potentially many instances of an SLINK controller on tegra and only a single instance of SFLASH. Tegra20 is currently ths only version of tegra that instantiates an SFLASH controller. This driver supports basic PIO mode of operation and is configurable (CONFIG_OF_CONTROL) to be driven off devicetree bindings. Up to 4 devices per controller may be attached, although typically only a single chip select line is exposed from tegra per controller so in reality this is usually limited to 1. To enable this driver, use CONFIG_TEGRA_SLINK Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra30: fdt: add SPI SLINK nodesAllen Martin2013-02-11-0/+5
| | | | | | | | Add tegra30 SPI SLINK nodes to fdt. Signed-off-by: Allen Martin <amartin@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: fdt: add back missing host1x nodeAllen Martin2013-02-11-0/+11
| | | | | | | | Add back host1x node to seaboard dts file. This got dropped during the tegra fdt sort. Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
generated by cgit v1.1 at 2024-11-06 05:14:58 +0000