summaryrefslogtreecommitdiff
path: root/board/logicpd
Commit message (Collapse)AuthorAgeLines
* omap3: zoom1: switch to generic ti_omap3_common config headerNishanth Menon2014-04-17-1/+0
| | | | | | | | ti_omap3_common contains a lot of common header definitions that help reduce the size of the zoom1 config file. So, use the generic header and customize as needed for the platform (example: no spl). Signed-off-by: Nishanth Menon <nm@ti.com>
* OMAP3: zoom1: enable LAN9211Nishanth Menon2014-04-17-2/+18
| | | | | | | Zoom1 was wrongly setup for LAN91C96. Fix it by enabling LAN9211. Signed-off-by: Nishanth Menon <nm@ti.com>
* OMAP3: zoom1: Configure GPMC for EthernetNishanth Menon2014-04-17-6/+31
| | | | | | zoom1 uses LAN9211 configured over GPMC Chip Select 1. Signed-off-by: Nishanth Menon <nm@ti.com>
* TI:omap3: Drop omap3_zoom2Tom Rini2014-01-07-702/+0
| | | | | | | The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ and Tom Rix's email has long been bouncing. Signed-off-by: Tom Rini <trini@ti.com>
* am3517_evm: activate Ethernet PHYYegor Yefremov2013-12-12-1/+33
| | | | | | | Pin 30 is connected to PHY's RESET# signal, so it must be put to high. Otherwise PHY won't be found via MDIO interface. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
* i2c, omap24xx: convert driver to new mutlibus/mutliadapter frameworkHeiko Schocher2013-11-13-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - add omap24xx driver to new multibus/multiadpater support - adapted all config files, which uses this driver Tested on the am335x based siemens boards rut, dxr2 and pxm2 posted here: http://patchwork.ozlabs.org/patch/263211/ Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Tom Rini <trini@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Thomas Weber <weber@corscience.de> Cc: Tom Rix <Tom.Rix@windriver.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Nishanth Menon <nm@ti.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Michael Jones <michael.jones@matrix-vision.de> Cc: Raphael Assenat <raph@8d.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Stefano Babic <sbabic@denx.de>
* board: arm: convert makefiles to Kbuild styleMasahiro Yamada2013-11-01-124/+11
| | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Tom Rini <trini@ti.com>
* Coding Style cleanup: remove trailing empty linesWolfgang Denk2013-10-14-1/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-382/+24
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* omap_hsmmc: add driver check for write protectionNikita Kiryanov2013-03-08-4/+4
| | | | | | | | Add check for write protection in omap mmc driver. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
* omap_hsmmc: implement driver check for card detectionNikita Kiryanov2013-03-08-7/+4
| | | | | | | Implement driver check for card detection. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* am3517_evm: switch to musb-newIlya Yanok2012-11-20-0/+74
| | | | | | Use new musb framework instead of the old one on AM3517_EVM. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* mx31: Fix PDR0_CSI_PODFBenoît Thébaudeau2012-10-15-1/+1
| | | | | | | | | | The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0 register is actually composed of two bit-fields: one pre-divider and one post-divider. This patch fixes the CCM access macros and the code using them accordingly. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
* serial: zoom2: Remove zoom2 serial prototypes from serial.hMarek Vasut2012-10-15-1/+6
| | | | | | | | | | | | | | Remove the prototypes for zoom2_serial_deviceN from serial.h . This can't be done right away, as they are referenced from the zoom2 config file. Therefore, adjust the code so the config file only specifies number of the port. Then, replace the simple return in default_serial_console() with a switch across possible values, which returns the zoom2_serial_deviceN . With such adjustment in place, the exported prototypes in serial.h can be safely removed. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
* serial: Properly spell out the structure member names of serial_driverMarek Vasut2012-10-15-8/+8
| | | | | | | | | | | | | | | | | Properly spell out the whole structure member names when an initialized varible is instantiated from the struct serial_driver. In case the structure definition for struct serial_driver undergoes reordering, there will be no impact on variables defined based on this structure. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: C Nauman <cnauman@diagraph.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Michal Simek <monstr@monstr.eu>
* COMMON: Use __stringify() instead of rest of implementationsMarek Vasut2012-10-15-4/+3
| | | | | | | Fix up the rest of implementations of __stringify(). Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de>
* imx27lite: update with gpio api change (v4)trem2012-09-01-3/+2
| | | | | Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr> Acked-by: Stefano Babic <sbabic@denx.de>
* omap3: Introduce weak misc_init_rTom Rini2012-05-15-11/+0
| | | | | | | | | | | | | Introduce a __weak misc_init_r function that just runs dieid_num_r(). Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was all they did for misc_init_r. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* ARM:OMAP+:MMC: Add parameters to MMC initJonathan Solnit2012-05-15-4/+4
| | | | | | | | | | Add parameters to the OMAP MMC initialization function so the board can mask host capabilities and set the maximum clock frequency. While the OMAP supports a certain set of MMC host capabilities, individual boards may be more restricted and the OMAP may need to be configured to match the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example. Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
* omap3logic: Add missing GPMC pinmux for LAN92xx accessPeter Barada2012-02-12-0/+15
| | | | | | | The initial checkin dropped pinmux setup for GPMC pins A6-A10, D0-D7 and NCS1/2 necessary to access LAN92xx on Logic OMAP35x/DM37x modules. Signed-off-by: Peter Barada <peter.barada@logicpd.com>
* ARMV7: Add support For Logic OMAP35x/DM37x modulesPeter Barada2012-01-16-0/+336
| | | | | | | | | | | | This patch adds basic support for OMAP35x/DM37x SOM LV/Torpedo reference boards. It assumes U-boot is loaded to SDRAM with the help of another small bootloader (x-load) running from SRAM. Signed-off-by: Peter Barada <peter.barada@logicpd.com> Cc: Tom Rini <tom.rini@gmail.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* AM3517: Add SPL supportTom Rini2011-12-06-31/+1
| | | | | | | | The only change of note is that we move from 0x80008000 to 0x80100000 for CONFIG_SYS_TEXT_BASE Cc: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* AM3517: move AM3517 specific mux defines to generic headerIlya Yanok2011-12-06-40/+0
| | | | | | | AM3517 specific CONTROL_PADCONF_* defines moved from board-specific files to <asm/arch-omap3/mux.h> Signed-off-by: Ilya Yanok <yanok@emcraft.com>
* omap: Don't use gpio_free to change direction to inputJoe Hershberger2011-10-27-2/+0
| | | | | | | | | gpio_free() should not have the side effect of setting the line to input since this prevents the gpio command from being able to set a line as output. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* imx: fix coding styleFabio Estevam2011-10-27-4/+4
| | | | | | | | | Fix checkpatch warning and errors in several i.MX related files. While at it also address a checkpatch warning at arch/arm/cpu/armv7/mx5/soc.c regarding the usage of extern in a C file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx31: provide readable WEIM CS accessorHelmut Raiger2011-10-27-6/+22
| | | | | | | | | | | | setup_weimcs() and some macros are added to support the setup for i.MX31 WEIM chip selects. As a compromise between verbosity and readability an ASCII-art'ish bit comment is used instead of bitfields. All i.MX31 boards have been patched to use this approach using a helper program to verify the changes. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Acked-by: Stefano Babic <sbabic@denx.de>
* punt unused clean/distclean targetsMike Frysinger2011-10-15-30/+0
| | | | | | | | | | The top level Makefile does not do any recursion into subdirs when cleaning, so these clean/distclean targets in random arch/board dirs never get used. Punt them all. MAKEALL didn't report any errors related to this that I could see. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* imx31_litekit: Place machine ID into board configFabio Estevam2011-09-30-1/+0
| | | | | | Let common code set the machine ID. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx31_litekit: Remove dram_init_banksize()Fabio Estevam2011-09-30-6/+0
| | | | | | As only one RAM bank is used we can rely on the code from arch/arm/lib/board.c Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* led: remove camel casing of led identifiers globallyJason Kridner2011-09-13-14/+14
| | | | | | | | | | | | | | | Result of running the following command to address Wolfgang's comment about camel case: for file in `find . | grep '\.[chS]$'`; do perl -i -pe 's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done Discussion: http://patchwork.ozlabs.org/patch/84988/ Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap: gpio: Adapt board files to use generic APISanjeev Premi2011-09-13-29/+29
| | | | | | | This patch contains updates the sources in the board files to use the generic API. Signed-off-by: Sanjeev Premi <premi@ti.com>
* Makefile : fix generation of cpu related asm-offsets.hStefano Babic2011-09-07-1/+1
| | | | | | | | | | | commit 0edf8b5b2fa0d210ebc4d6da0fd1aceeb7e44e47 breaks building on a different directory with the O= parameter. The patch wil fix this issue, generating always asm-offsets.h before the other targets. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Matthias Weisser <weisserm@arcor.de> CC: Wolfgang Denk <wd@denx.de>
* OMAP3: Zoom2: Use generic MMC driverTom Rini2011-09-04-0/+9
| | | | | | | | Switch from the legacy omap3 mmc driver to the new generic omap hsmmc driver. This patch is based on the work done for Beagle, etc. Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3: Zoom1: Use generic MMC driverTom Rini2011-09-04-0/+9
| | | | | | | | Switch from the legacy omap3 mmc driver to the new generic omap hsmmc driver. This patch is based on the work done for Beagle, etc. Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* am3517evm: Use generic MMC driverVaibhav Hiremath2011-09-04-0/+9
| | | | | | | | | | | | | Switch from the legacy mmc driver to the new generic mmc driver. This patch is based on similar patch for beagle[1]. [1] http://git.denx.de/?p=u-boot.git;a=commitdiff_plain;h=0cd31144240 Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* serial: drop useless ctlr fieldMike Frysinger2011-07-26-2/+0
| | | | | | | | | | | | | | | | | | | The multi serial support has a "ctlr" field which almost no one uses, but everyone is forced to set to useless strings. So punt it. Funny enough, the only code that actually reads this field (the mpc8xx driver) has a typo where it meant to look for the SCC driver. Fix it while converting the check to use the name field. Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Heiko Schocher <hs@denx.de> CC: Anatolij Gustschin <agust@denx.de> CC: Tom Rix <Tom.Rix@windriver.com> CC: Minkyu Kang <mk7.kang@samsung.com> CC: Craig Nauman <cnauman@diagraph.com> CC: Marek Vasut <marek.vasut@gmail.com> CC: Prafulla Wadaskar <prafulla@marvell.com> CC: Mahavir Jain <mjain@marvell.com>
* serial: push default_serial_console to driversMike Frysinger2011-07-26-0/+5
| | | | | | | | | | | | | | | | | Rather than sticking arch/board/driver specific logic in the common serial code, push it all out to the respective drivers. The serial drivers declare these funcs weak so that boards can still override things with their own definition. Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Heiko Schocher <hs@denx.de> CC: Anatolij Gustschin <agust@denx.de> CC: Tom Rix <Tom.Rix@windriver.com> CC: Minkyu Kang <mk7.kang@samsung.com> CC: Craig Nauman <cnauman@diagraph.com> CC: Prafulla Wadaskar <prafulla@marvell.com> CC: Mahavir Jain <mjain@marvell.com> Tested-by: Minkyu Kang <mk7.kang@samsung.com>
* Remove volatile qualifier in get_ram_size() callsAlbert ARIBAUD2011-07-17-4/+4
| | | | | | | | | Checkpatch.pl complains about the volatile qualifier in calls to get_ram_size(). Remove this qualifier in the prototype and in the calls where it is useless, and leave it only in the function body where it is needed. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* mx27: Make the UART port number explicitFabio Estevam2011-07-14-1/+1
| | | | | | | | mx27_uart_init_pins does the IOMUX setting for UART1 port. Change the function name to make the UART port number explicit. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx27lite: Remove local config.mkFabio Estevam2011-06-07-5/+0
| | | | | | | | Local board config.mk should be avoided. Place CONFIG_SYS_TEXT_BASE definition into the board config file instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx31_litekit: Remove local config.mkFabio Estevam2011-06-07-1/+0
| | | | | | | | | Local board config.mk should be avoided. Place CONFIG_SYS_TEXT_BASE definition into the board config file instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* mx31litekit: Fix boot with the new relocation scheme.Fabio Estevam2011-06-06-6/+11
| | | | | | | | | imx31_litekit has been converted to the new relocation scheme, but it does not boot. Make the boot functional by using board_early_init_f . Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
* IMX: MX31: Cleanup include files and drop nasty #ifdef in driversStefano Babic2011-04-27-3/+3
| | | | | | | | | | As exception among the i.MX processors, the i.MX31 has headers without general names (mx31-regs.h, mx31.h instead of imx-regs.h and clock.h). This requires several nasty #ifdef in the drivers to include the correct header. The patch cleans up the driver and renames the header files as for the other i.MX processors. Signed-off-by: Stefano Babic <sbabic@denx.de>
* Move DECLARE_GLOBAL_DATA_PTR to file scopeJohn Rigby2010-12-21-3/+4
| | | | | | | | | | | | | | | It can be optimised out by the compiler otherwise resulting in obscure errors like a board not booting. This has been documented in README since 2006 when these were first fixed up for GCC 4.x. Signed-off-by: John Rigby <john.rigby@linaro.org> Fix some additional places. Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
* OMAP3: Zoom2: Fix ARM relocation supportDirk Behme2010-11-30-1/+1
| | | | | Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3: Zoom1: Fix ARM relocation supportDirk Behme2010-11-30-1/+1
| | | | | Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* AM3517:Fix for ARM Relocation supportVaibhav Hiremath2010-11-29-1/+1
| | | | | | | | | Also change the CONFIG_SYS_TEXT_BASE to 0x80008000, required with relocation support. This is the load address for primary boot loader (x-loader). Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Switch from archive libraries to partial linkingSebastien Carlier2010-11-17-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | Before this commit, weak symbols were not overridden by non-weak symbols found in archive libraries when linking with recent versions of binutils. As stated in the System V ABI, "the link editor does not extract archive members to resolve undefined weak symbols". This commit changes all Makefiles to use partial linking (ld -r) instead of creating library archives, which forces all symbols to participate in linking, allowing non-weak symbols to override weak symbols as intended. This approach is also used by Linux, from which the gmake function cmd_link_o_target (defined in config.mk and used in all Makefiles) is inspired. The name of each former library archive is preserved except for extensions which change from ".a" to ".o". This commit updates references accordingly where needed, in particular in some linker scripts. This commit reveals board configurations that exclude some features but include source files that depend these disabled features in the build, resulting in undefined symbols. Known such cases include: - disabling CMD_NET but not CMD_NFS; - enabling CONFIG_OF_LIBFDT but not CONFIG_QE. Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
* Merge branch 'elf_reloc'Wolfgang Denk2010-10-19-0/+4
|\ | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/include/asm/config.h board/LaCie/edminiv2/config.mk board/karo/tx25/config.mk board/logicpd/imx27lite/config.mk doc/README.arm-relocation Signed-off-by: Wolfgang Denk <wd@denx.de>
| * arm926ejs, magnesium: add support for ELF relocationsHeiko Schocher2010-10-13-0/+3
| | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de>