arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	arm: Move cpu/$CPU to arch/arm/cpu/$CPU	Peter Tyser	2010-04-13	-1/+1
\| \| \| \|	Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
*	ppc: Move cpu/$CPU to arch/ppc/cpu/$CPU	Peter Tyser	2010-04-13	-1/+1
\| \| \| \|	Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
*	TWL4030: make LEDs selectable for twl4030_led_init()	Grazvydas Ignotas	2010-01-04	-1/+1
\| \| \| \| \| \| \| \| \| \| \| \|	Not all boards have both LEDs hooked, so enabling both on boards with single LED will just waste power. Make it possible to choose LEDs by adding argument to twl4030_led_init(). Using this turn on only LEDB for pandora, leave both LEDs on for all other boards, as it was before this patch. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
*	Merge branch 'master' of git://git.denx.de/u-boot-usb	Wolfgang Denk	2009-12-21	-4/+8
\|\
\| *	OMAP3 zoom2 Use usbtty if the debug board is not connected.	Tom Rix	2009-12-20	-4/+8
\| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \|	The preferred serial output comes from the debug board. When the debug board is disconnected, fall back on using usbtty from the usb connector on the Zoom2 board. This shows up as /dev/ttyACM0 in a linux host. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* \|	Net: Clean up LAN91C96 Support	Ben Warren	2009-12-14	-0/+12
\|/ \| \| \| \| \| \| \|	A previous Commit converted the LAN91C96 Ethernet driver to using the CONFIG_NET_MULTI API, but did not include full board support. This patch finishes the job. Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
*	TI OMAP3: make gpmc_config as const	Nishanth Menon	2009-10-24	-3/+0
\| \| \| \| \| \| \| \| \| \| \|	gpmc_config should not be a variant as it is board specific hence make it a const parameter Fixes issues identified by Dirk: - build issue for zoom2 - warnings for all other OMAP3 platforms using nand/onenand etc Signed-off-by: Nishanth Menon <nm@ti.com>
*	Zoom2 Fix serial gpmc setup	Tom Rix	2009-10-18	-1/+1
\| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \|	The offset to the chip select is incorrect. The change 187af954cf7958c24efcf0fd62289bbdb4f1f24e, omap3: embedd gpmc_cs into gpmc config struct introduced a problem with the serial gpmc setup. This patch reverts the chip select to its previous value. The symptoms of this problem are that the Zoom2 currently hangs. This was run tested on Zoom2. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
*	OMAP3: Clean up whitespace in mux configs	Olof Johansson	2009-10-13	-94/+94
\| \| \| \| \| \| \| \| \| \| \|	Switch from space-based indentation to tab-based in mux configs, as pointed out by WD at: http://lists.denx.de/pipermail/u-boot/2009-September/061241.html Nothing but whitespace changes in this patch (diff -w gives no output). Signed-off-by: Olof Johansson <olof@lixom.net>
*	arm: move Logicpd's boards to board/logicpd/	Jean-Christophe PLAGNIOL-VILLARD	2009-09-05	-0/+819
	Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>