summaryrefslogtreecommitdiff
path: root/board/keymile/common
Commit message (Collapse)AuthorAgeLines
* powerpc/83xx: move km 83xx specific i2c code to km83xx_i2cHolger Brunck2011-11-03-65/+9
| | | | | | | | | The common code should be valid for more than one architecture. Therefore this code was reorganized and moved to the new file km83xx_i2c.c Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* km/common: remove obsolete header fileHolger Brunck2011-10-22-4/+0
| | | | | | | | This header is unneeded due to code which was removed in the past. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Wolfgang Denk <wd@denx.de>
* km/common: fix ramfs development targetAndreas Huber2011-10-22-2/+14
| | | | | | | | | | Calucations of PRAM needs to take into account the 'rootfssize'. Memory available to the linux kernel 'mem=' is in all cases set to the total memory size minus the pram size. Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Wolfgang Denk <wd@denx.de>
* km/common: force set ethaddr only for KM kirkwood boardsHolger Brunck2011-10-22-0/+5
| | | | | | | | This prevents u-boot to print out "Can't overwrite "ethaddr"" each time a powerpc board starts. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Wolfgang Denk <wd@denx.de>
* km/common: fix bug in IVM mac address accessHolger Brunck2011-09-21-2/+2
| | | | | | | | The MAC address stored in the inventory eeprom begins at offset 1. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Wolfgang Denk <wd@denx.de>
* km/common: i2c deblock: enabled print of i2c deblock statusStefan Bigler2011-07-28-0/+3
| | | | | | | | | | Enable printout of i2c deblocking status if chips were in block state or deblocking failed. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: add printings to boardid commandsHolger Brunck2011-07-28-1/+5
| | | | | | | | | | Be verbose if do_setboardid was called and print correct names of variables in do_checkboardidhwk. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* powerpc/km82xx: remove 82xx specific functions from common.cHolger Brunck2011-07-27-68/+2
| | | | | | | | | | Common code should be valid for more than one architecture, therefore the km82xx specific code was removed from common.c. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: remove fdt_(gs)et_node_and_valueHolger Brunck2011-07-27-55/+0
| | | | | | | | | This code is unused and therefore dead code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: move ivm functions from to ivm.cHolger Brunck2011-07-27-318/+349
| | | | | | | | | | The file common.c grows in the past. So move the IVM specific code into an ivm.c file. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: remove saveenv from do_checkboardidhwkeyHolger Brunck2011-07-27-6/+1
| | | | | | | | | | | This is unneeded here because we save the environment when the board boots the first time. At this time we have set the values already. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: force set ethaddr after reading IVMHolger Brunck2011-07-27-2/+1
| | | | | | | | | | | | | | The ethaddr is stored inside the inventory eeprom. During boottime this value was read out and the ethaddr variable was set. Previously this was only done if it ethaddr == NULL but this is wrong for our ARM boards. Because ethaddr is at this stage never NULL for ARM due to the random calculation of a MAC address in mvgbe.c. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: remove obsolete defines and headerHolger Brunck2011-07-27-129/+0
| | | | | | | | | | These defines and the header keymile_hdlc_enet.h are obsolete due to the removed hdlc code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: implement boardId HWkey checks as u-boot cmdThomas Herzmann2011-05-18-0/+156
| | | | | | | | | | | | | | | | | | | | | | | | BoardId and HWKey are used to identify the HW class of a given board. The correct values are stored in the inventory eeprom. During creation time of a boot package the boardId and HWkey for the SW is stored in the default environment and burned into the flash. During boottime the values in the inventory and in the environment are compared to avoid starting of a SW which is not authorized for this board. Some bootpackages are allowed to run on a set of different boardId hwKey. In this case the environment variable boardIdListHex was added to the default environment. In this case the command iterates over the pair values and compares them with the values read from the inventory eeprom. The syntax of such a boardIdListHex value is e.g.: 158_1 159_1 159_2 Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de>
* km/common: implement setboardid commandHolger Brunck2011-05-10-0/+34
| | | | | | | | | | | Read out board id and HW key from the IVM eeprom and set these values as an environment variable. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* powerpc/km82xx: add mgcoge3ne and remove mgcoge2ne supportHolger Brunck2011-05-10-3/+4
| | | | | | | | | | | | | | | | | This patch adds support for the MPC8247 based board mgcoge3ne. Additionaly mgcoge2ne board supprot was removed, because due to the mgcoge3ne, this board is obsolete and not longer maintained. The board is similar to mgcoge. The difference is that a NUMONYX flash is used and a different SDRAM (256MB). Also introduce CONFIG_KM_82XX to collect ppc82xx common settings and remove staticness from the common set_pin function. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de>
* powerpc/km82xx: rework DIP switch detectionHuber, Andreas2011-05-10-0/+79
| | | | | | | | | | | | | Introduce a struct for the BFTICU FPGA to increase the readability of the code. And the define CONFIG_SYS_BFTICU_BASE was removed because the CONFIG_SYS_FPGA_BASE is already the base value for BFTICU registers. Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de>
* km/common: remove hdlc_enet implementationHolger Brunck2011-05-10-627/+0
| | | | | | | | | | | | | The hdlc implementation for mgcoge was initially developed, but later on not used. Remove the C files, the references in mgcoge.c and the Makefile to decrease maintenance effort. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* keymile, common: add setting of some environment variablesHeiko Schocher2011-04-30-0/+37
| | | | | | | | | | | | | This patch adds last_stage_init to all keymile boards. And in the last stage init some environment variables for u-boot were set. Currently these are pnvramaddr, pram and var address. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Wolfgang Denk <wd@denx.de> cc: Kim Phillips <kim.phillips@freescale.com>
* keymile boards: add CONFIG_PIGGY_MAC_ADRESS_OFFSETHeiko Schocher2011-04-30-0/+17
| | | | | | | | | | | | Normaly the PIGGY_MAC_ADRESS can be read directly from the IVM on keymile boards. On mgcoge3 it differs. Because there are two piggy boards deployed the second MAC adress must be calculated with the IVM mac adress and an offset. This patch allows to set such a offset in the board config. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de>
* keymile, common; fix i2c deblocking supportHeiko Schocher2011-04-30-32/+89
| | | | | | | | | | | | | | | | | | This patch fix the i2c deblocking facility with the i2c HW-Controller. The required delays for byte reading, the enhanced criteria for stop the dummy read and required 5 start/stop sequences are added. Add i2c deblocking before ivm eeprom read. Improve i2c deblocking sequence by respecting stop hold time. Cleaned function for deblocking. Have now one function i2c_make_abort() available for bitbang, mpc82xx and mpc83xx harware controller. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* ppc, 8321: cleanup tuxa1, tuda1 and suvd3 supportHeiko Schocher2011-04-30-1/+2
| | | | | | | | | | | | | | | | | | | | | For the kmsupx5 a new header file was introduced km8321-common.h. Now the common stuff from tuxa1, tuda1 and suvd3 was removed and the new header file included. The defines CONFIG_SYS_PIGGY_BASE and CONFIG_SYS_PIGGY_SIZE are confusing. Because they actually describe the KMBEC FPGA values. The KMBEC FPGA can be PRIO on kmeter1 or upio on mgcoge. Therefore all the defines were renamed. remove unneeded variable CONFIG_KM_DEF_NETDEV, as it is already declared in keymile-common.h Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Wolfgang Denk <wd@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* ppc: add support for ppc based board mgcoge2neHeiko Schocher2011-04-30-2/+2
| | | | | | | | | | | | | | | | | The mgcoge2 board from keymile deploys two different processors. An ARM based Kirkwood for the "unit" part of the SW and a PPC for the "ne" part of the SW. Therefore in Linux and U-Boot the names for the board are mgcoge2un and mgcoge2ne. This patch adds the mgcoge2ne part of the board. The ppc part of mgboge2 is quite similar to mgcoge, therefore a generic header km82xx-common.h was introduced to collect all similiarities. Currently the only difference is that mgcoge2ne has a 64 MB numonyx NOR flash with a single die. The mgcoge has a dual die flash 2*32MB from spansion. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* mpc832x: add support for the mpc8321 based suvd3 boardHeiko Schocher2011-04-30-4/+6
| | | | | | | | | | | | | | | | | | | | - serial console on UART1 - Ethernet RMII over UCC4 - PHY SMSC LAN8700 - 64MB Flash - 128 MB DDR2 RAM - I2C - bootcount This board is similiar to the kmeter1 (8360) board, so common config options are extracted into the include/configs/km83xx-common.h file. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* keymile: Fix Coding style issues for keymile boards.Heiko Schocher2011-04-30-188/+199
| | | | | | | | | | | | | | | | | | | - use I/O accessors -> For accessing the FPGA therefore a struct km_bec_fpga is introduced. - no longer externs needed - to defines, that only select functions, don;t assign a numeric value - Codingstyle changes to prevent checkpatch errors/warnings Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm, keymile: rename MACH_SUEN3 to MACH_KM_KIRKWOODHolger Brunck2011-04-30-2/+2
| | | | | | | | | | | | The MACH_TYPE SUEN3 is now to specific for keymile boards, because other boards similar to suen3 will follow. So the MACH_SUEN3 was renamed to MACH_KM_KIRKWOOD. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* net ppc: fix ethernet device names with spacesHeiko Schocher2010-08-09-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | since commit 1384f3bb8a4f9066805b70c1418eda78ecb73fdd ethernet names with spaces drop a Warning: eth device name has a space! message. This patch fix it for: - "FEC ETHERNET" devices found on mpc512x, mpc5xxx, mpc8xx and mpc8220 boards. renamed to "FEC". - "SCC ETHERNET" devices found on mpc8xx, mpc82xx based boards. Renamed to "SCC". - "HDLC ETHERNET" devices found on mpc8xx boards Renamed to "HDLC" - "FCC ETHERNET" devices found on mpc8260 and mpc85xx based boards. Renamed to "FCC" Tested on the kup4k board. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Move arch/ppc to arch/powerpcStefan Roese2010-04-21-1/+1
| | | | | | | | | | | | | | | | | As discussed on the list, move "arch/ppc" to "arch/powerpc" to better match the Linux directory structure. Please note that this patch also changes the "ppc" target in MAKEALL to "powerpc" to match this new infrastructure. But "ppc" is kept as an alias for now, to not break compatibility with scripts using this name. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Wolfgang Denk <wd@denx.de> Acked-by: Detlev Zundel <dzu@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Anatolij Gustschin <agust@denx.de>
* ppc: Move cpu/$CPU to arch/ppc/cpu/$CPUPeter Tyser2010-04-13-1/+1
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* arm: add support for the suen3 board from keymileHeiko Schocher2010-03-07-2/+4
| | | | | | | | | | | | | Add support for the ARM part of the mgcoge2, named suen3. This board is based on the Marvell Kirkwood (88F6281) SoC. As there come more board variants, common config options are collected in include/configs/km_arm.h. Also, this board use common code for all keymile boards, which is stored in board/keymile/common/common.c Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Heiko Schocher <hs@denx.de>
* i2c, mpc83xx: add CONFIG_SYS_I2C_INIT_BOARD for fsl_i2cHeiko Schocher2009-07-21-0/+20
| | | | | | | | | | | | | | | | | | | | | | This patch adds the possibility to call a board specific i2c bus reset routine for the fsl_i2c bus driver, and adds this option for the keymile kmeter1 board. The deblock sequence for this board is implemented and tested in the following way: CR = 0x20 (release SDA and SCL pin) CR = 0xa0 (start read) dummy read dummy read if 2. dummy read == 0x00 3. dummy read CR = 0x80 (SDA and SCL now 1 SR = 0x86) CR = 0x00 (Modul reset SR=0x81) CR = 0x80 (SDA and SCL = 1, SR = 0x81) Signed-off-by: Heiko Schocher <hs@denx.de>
* powerpc: updates for the keymile boardsHeiko Schocher2009-07-21-3/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - CONFIG_SYS_MAX_I2C_BUS changed to 1 We use only one I2C hardwarecontroller on this boards, so change the CONFIG_SYS_MAX_I2C_BUS to 1. - common: dont print errormsg if second IVM Block lacks. - 82xx, mgcoge: fix double mtdpart entry in environment - 82xx, mgcoge: activate on second Flash the second bank. - common: CONFIG_ENV_SIZE 0x4000 for all keymile boards - common: Change malloc size to 1MByte for all Keymile boards We need a bigger malloc area for the environment support (128k) on some Keymile boards (kmeter1) and the upcoming UBI support. Change it to 1MB for all Keymile boards to be on the save side. Also define CONFIG_SYS_64BIT_VSPRINTF which is needed for UBI/UBIFS support. - Add UBI support to all Keymile boards - change manner of writing "/localbus/ranges" node instead of writting the complete "/localbus/ranges" node before booting Linux, only update the ranges entries which gets dynamical detected (size of flashes). This is needed, because keymile adds in the DTS "/localbus/ranges" node entries, which u-boot must not overwrite/delete. - kmeter, mgcoge: define 2 seperate regions needed for the Intel P30 chips The Intel P30 chip has 2 non-identical chips on one die, so we need to define 2 seperate regions that are scanned by physmap_of independantly. - kmeter1: Add MTD concat support to Keymile boards - 82xx, mgcoge: add "unlock=yes" to default environment - added CONFIG_MTD_DEVICE to get in sync with mainline code Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* General help message cleanupWolfgang Denk2009-06-12-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many of the help messages were not really helpful; for example, many commands that take no arguments would not print a correct synopsis line, but "No additional help available." which is not exactly wrong, but not helpful either. Commit ``Make "usage" messages more helpful.'' changed this partially. But it also became clear that lots of "Usage" and "Help" messages (fields "usage" and "help" in struct cmd_tbl_s respective) were actually redundant. This patch cleans this up - for example: Before: => help dtt dtt - Digital Thermometer and Thermostat Usage: dtt - Read temperature from digital thermometer and thermostat. After: => help dtt dtt - Read temperature from Digital Thermometer and Thermostat Usage: dtt Signed-off-by: Wolfgang Denk <wd@denx.de>
* 8xx: add support for new keymile kmsupx4 board.Heiko Schocher2009-03-18-0/+4
| | | | | | | | | | | | | This patch adds support for the kmsupx4 board from Keymile, based on a Freescale MPC852T CPU - serial console on SMC1 - 32 MB SDRAM - 32 MB NOR Flash - Ethernet over SCC3 - I2C Bitbang Signed-off-by: Heiko Schocher <hs@denx.de>
* 8xx, mgsuvd: rename board to a more generic nameHeiko Schocher2009-03-18-2/+2
| | | | | | | | | renaming the "mgsuvd" board port into "km8xx", because there come more similar boards from keymile. Compiling the mgsuvd board with "make mgsuvd_config" remains. Signed-off-by: Heiko Schocher <hs@denx.de>
* 83xx, kmeter1: add I2C, dtt, eeprom supportHeiko Schocher2009-03-05-1/+1
| | | | | | | | | | This patch adds I2C support for the Keymile kmeter1 board. It uses the First I2C Controller from the CPU, for accessing 4 temperature sensors, an eeprom with IVM data and the booteeprom over a pca9547 mux. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Command usage cleanupPeter Tyser2009-01-28-2/+2
| | | | | | | | Remove command name from all command "usage" fields and update common/command.c to display "name - usage" instead of just "usage". Also remove newlines from command usage fields. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* powerpc: keymile: Add a check for the PIGGY debug boardHeiko Schocher2009-01-24-2/+41
| | | | | | | | | Check the presence of the PIGGY on the keymile boards mgcoge, mgsuvd and kmeter1. If the PIGGY is not present, dont register this Ethernet device. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Ben Warren <biggerbadderben@gmail.com>
* keymile add the common parts of the HDLC driverGary Jennejohn2008-12-07-0/+749
| | | | | | | This implements the ICN protocol used across the backplane and is needed by all the keymile boards. Signed-off-by: Gary Jennejohn <garyj@denx.de>
* mgcoge, mgsuvd: extract more common codeHeiko Schocher2008-10-18-0/+26
| | | | | | | | in ft_blob_update () for both boards was an unneccessary repetition of code, which this patch moves in a common function for this boards. Signed-off-by: Heiko Schocher <hs@denx.de>
* mgsuvd: fix compiler warning when using soft_i2c driverHeiko Schocher2008-10-18-1/+2
| | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD2008-10-18-22/+22
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* mgcoge, mgsuvd: added support for the IVM EEprom.Heiko Schocher2008-10-18-0/+287
| | | | | | | | The EEprom contains some Manufacturerinformation, which are read from u-boot at boot time, and saved in same hush shell variables. Signed-off-by: Heiko Schocher <hs@denx.de>
* mgcoge, mgsuvd: add board specific I2C deblocking mechanism.Heiko Schocher2008-10-18-0/+209
As documented in doc/I2C_Edge_Conditions, adding a board specific deblocking mechanism via CFG_I2C_INIT_BOARD for the mgcoge and mgsuvd board. This code was originally written by Keymile in association with Anatech and Atmel in 1998. The Code toggels the SCL until the SCA line goes to HIGH (max. 16 times). And after this, a start condition is sent. This is another approach to deblock the I2C Bus. The soft I2C driver actually sends 9 clocks with SDA High, and then a stop at the end, to deblock the I2C Bus. Maybe we should use the approach from Keymile as the new standard? Signed-off-by: Heiko Schocher <hs@denx.de>