arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	OMAP3: add video support to the mcx board	Stefano Babic	2012-10-25	-0/+43
\| \| \| \| \| \| \|	Add video support to the board with the display focaltech etm070003dh6. Signed-off-by: Stefano Babic <sbabic@denx.de>
*	OMAP3: mcx: updated to new hardware revision	Stefano Babic	2012-10-25	-17/+4
\| \| \| \| \| \| \| \|	Some GPIOs differ in the new revision board. Previous revision are considered obsolete and they will not anymore supported. Signed-off-by: Stefano Babic <sbabic@denx.de>
*	OMAP3: updated pinmux and environment for new revision of mcx board	Stefano Babic	2012-10-25	-13/+13
\| \| \| \| \| \| \|	The mcx board was slightly modified and the pinmux must be updated. There is no need to support the old board, that becomes obsolete. Signed-off-by: Stefano Babic <sbabic@denx.de>
*	usb: ehci: rework to take advantage of new lowlevel interface	Lucas Stach	2012-10-15	-3/+3
\| \| \| \| \| \| \| \| \| \| \| \| \| \|	Kill off ehci-core.h It was used to specify some static controller data. To support more than one controller being active at any time we have to carry the controller data ourselfes. Change the ehci interface accordingly. NOTE: OMAP implemented the ehci stuff a bit backwards and should be fixed to do the same thing as other platforms. But the change for now is at least compile clean. Signed-off-by: Lucas Stach <dev@lynxeye.de> Reviewed-by: Marek Vasut <marex@denx.de>
*	OMAP3: mcx: read hot-water-button after reset	Stefano Babic	2012-09-01	-0/+23
\| \| \| \| \| \| \|	Detect hot-water-button to start a differnt image. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
*	OMAP3: mcx: set pinmux for uart4	Stefano Babic	2012-09-01	-3/+8
\| \| \| \| \|	Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
*	omap3: Introduce weak misc_init_r	Tom Rini	2012-05-15	-11/+0
\| \| \| \| \| \| \| \| \| \| \| \| \|	Introduce a __weak misc_init_r function that just runs dieid_num_r(). Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was all they did for misc_init_r. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
*	ARM:OMAP+:MMC: Add parameters to MMC init	Jonathan Solnit	2012-05-15	-1/+1
\| \| \| \| \| \| \| \| \| \|	Add parameters to the OMAP MMC initialization function so the board can mask host capabilities and set the maximum clock frequency. While the OMAP supports a certain set of MMC host capabilities, individual boards may be more restricted and the OMAP may need to be configured to match the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example. Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
*	mcx: support for HTKW mcx board	Ilya Yanok	2012-02-12	-0/+558
	This patch adds support for the HTKW mcx AM3517-based board. Serial, Ethernet, NAND, MMC, RTC, EHCI USB host and both NAND and MMC SPLs are supported. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> Cc: Detlev Zundel <dzu@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>