summaryrefslogtreecommitdiff
path: root/board/genesi/mx51_efikamx/imximage_mx.cfg
Commit message (Collapse)AuthorAgeLines
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* Fix references to the documentation filesAnatolij Gustschin2013-05-10-1/+1
| | | | | | | | | | | | Many boot image configuration files refer to the appropriate documentation file, but these references contain typos in the directory and file name. Fix them. Also fix reference to doc/README.SPL file. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* imximage.cfg: run files through C preprocessorTroy Kisky2013-01-22-62/+70
| | | | | | | | | | | | The '#' used as comments in the files cause the preprocessor trouble, so change to /* */. The mkimage command which uses this preprocessor output was moved to arch/arm/imx-common/Makefile .gitignore was updated to ignore .cfgtmp files. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* efikamx: configure Smarttop PCBID and LED pads in DCD for convenienceMatt Sealey2012-09-01-0/+10
| | | | | | | | | | | | | | | | PCBID pads seem to need time to settle due to external pulldowns, otherwise we are reading floating GPIO pins with implicit pad pullups and get the wrong data. However we can't "wait" at the time we need them before relocation, since timers are not available. The time taken to get from DCD to the code requiring the pads set seems to be more than long enough (even with caches enabled). We have space in the DCD due to the DDR settings changes to configure all the pad settings we need for this, plus the LED pad settings too which reduces the amount of code required later on. Signed-off-by: Matt Sealey <matt@genesi-usa.com> Acked-by: Stefano Babic <sbabic@denx.de>
* efikamx: remove drive strength function and roll its functionality into the DCDMatt Sealey2012-09-01-24/+18
| | | | | | | | | | | | | | | | | | | Efika MX boards configure their DDR pad settings twice, one in the DCD generated from imximage_*.cfg and again in init_drive_strength called before relocation. Rather than doing this, roll the changes it makes into the DCD so DDR is set up before a single line of code in U-Boot is run. The settings are identical with this DCD block which is shorter (by 7 entries) than the old one, and after the output of init_drive_strength since a lot of the functionality in the existing DCD and init_drive_strength function was just setting the POR defaults. This goes to explain some now-missing entries. Several hundred rounds of mtest have been run to test the settings before and after to confirm DDR is stable and no ill-effects have been found. Signed-off-by: Matt Sealey <matt@genesi-usa.com> Acked-by: Stefano Babic <sbabic@denx.de>
* efikamx: move and rename Efika MX directories and config files to prepare ↵Matt Sealey2012-09-01-0/+122
for new boards * Move Efika MX Smarttop and Smartbook boards into a "genesi" vendor directory * Rename efikamx -> mx51_efikamx since there is an mx53_efikamx and mx6_efikamx to come Signed-off-by: Matt Sealey <matt@genesi-usa.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>